Search NASA⌕ Search

Engineering topics

Blaha, B. J.

Publications and source records attributed to Blaha, B. J..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

The NASA Altitude Wind Tunnel (AWT): Its role in advanced icing research and development

Currently experimental aircraft icing research is severely hampered by limitations of ground icing simulation facilities. Existing icing facilities do not have the size, speed, altitude, and icing environment simulation capabilities to allow accurate studies to be made of icing problems occurring for high speed fixed wing aircraft and rotorcraft. Use of the currently dormant NASA Lewis Altitude Wind Tunnel (AWT), as a proposed high speed propulsion and adverse weather facility, would allow many such problems to be studied. The characteristics of the AWT related to adverse weather simulation and in particular to icing simulation are discussed, and potential icing research programs using the AWT are also included.

Blaha, B. J.↗
NASA NTRS1985

The NASA altitude wind tunnel - Its role in advanced icing research and development

Currently experimental aircraft icing research is severly hampered by limitations of ground icing simulation facilities. Existing icing facilities do not have the size, speed, altitude, and icing environment simulation capabilities to allow accurate studies to be made of icing problems occurring for high speed fixed wing aircraft and rotorcraft. Use of the currently dormant NASA Lewis Altitude Wind Tunnel (AWT), as a proposed high speed propulsion and adverse weather facility, would allow many such problems to be studied. The characteristics of the AWT related to adverse weather simulation and in particular to icing simulation are discussed, and potential icing research programs using the AWT are also included.

Blaha, B. J.↗
NASA NTRS1981

Pneumatic boot for helicopter rotor deicing

Pneumatic deicer boots for helicopter rotor blades were tested. The tests were conducted in the 6 by 9 ft icing research tunnel on a stationary section of a UH-IH helicopter main rotor blade. The boots were effective in removing ice and in reducing aerodynamic drag due to ice.

Blaha, B. J.↗
NASA NTRS1979

Tone noise of three supersonic helical tip speed propellers in a wind tunnel

Three eight bladed supersonic helical tip speed propellers were tested in the NASA Lewis Wind Tunnel at through flow Mach numbers of 0.6, 0.7, 0.75, 0.8, and 0.85. Such propellers are being considered as propulsors for a future energy conservative aircraft. The three propellers of equal performance, incorporate different plan forms and different amounts of sweep in order to investigate their noise generation, which could cause a cabin environment problem. The acoustically designed propeller SR-3 had 45 deg of tip sweep and was significantly quieter at Mach 0.8 cruise than the straight bladed propeller, SR-2. An intermediate 30 deg tip sweep propeller, SR-1m exhibited a noise level between the other two. Enhanced pressure-time traces indicated that SR-2 and SR-1m exhibited shock-like pressure traces at Mach-0.8 cruise while the SR-3 did not. Noise trends with varying helical tip Mach number and blade loading were also observed.

Dittmar, J. H.↗
NASA NTRS1979

Wind tunnel performance of four energy efficient propellers designed for Mach 0.8 cruise

For the advanced turboprop to be competitive with proposed advanced turbofan-powered aircraft, it must have high propulsive efficiency at Mach 0.8 cruise above 9.144-km altitude with an acceptable cabin noise environment. Four 8-bladed propeller models are designed employing various concepts to reduce compressibility losses. Wind tunnel tests are conducted at zero model incidence to the free-stream flow. Aerodynamic and acoustic test results are presented and discussed. It is shown that the aeroacoustically designed configuration (SR-3) with 45 deg of tip sweep and an area-ruled spinner yields the highest propulsive efficiency (78.7% at Mach 0.8, 3.06 advance ratio, and 1.7 power coefficient), with an improvement of about 3% over the straight bladed configuration (SR-2, with zero-degree sweep). The phase-interference concept for noise reduction used in SR-3 yields about 5-6 dB reduction as compared to SR-2.

Jeracki, R. J.↗
NASA NTRS1979

Wind tunnel performance of four energy efficient propellers designed for Mach 0.8 cruise

Several advanced aerodynamic and acoustic concepts were investigated in recent wind tunnel tests performed in the NASA-Lewis Research Center 8x6 foot wind tunnel. These concepts included aerodynamically integrated propeller/nacelles, area-ruling, blade sweep, reduced blade thickness, and power (disk) loadings several times higher than conventional designs. Four eight-bladed propeller models were tested to determine aerodynamic performance. Relative noise measurements were made on three of the models at cruise conditions. Three of the models were designed with swept blades and one with straight blades. At the design Mach number of 0.8, power coefficient of 1.7, and advance ratio of 3.06, the straight bladed model had the lowest net efficiency of 75.8 percent. Increasing the sweep to 30 deg improved the performance to near 77 percent. Installation of an area-ruled spinner on a 30 deg sweep model further improved the efficiency to about 78 percent. The model with the highest blade sweep (45 deg) and an area-ruled spinner had the highest net efficiency of 78.7 percent, and at lower power loadings the efficiency exceeded 80 percent. At lower Mach numbers the 30 deg swept model had the highest efficiency. Values near 81 percent were obtained for the design loading at speeds to Mach 0.7. Relative noise measurements indicated that the acoustically designed 45 deg sweep model reduced the near field cruise noise by between 5 and 6 dB.

Jeracki, R. J.↗
NASA NTRS1979

Tone Noise of Three Supersonic Helical Tip Speed Propellers in a Wind Tunnel

Three supersonic helical tip speed propellers were tested in the NASA Lewis 8- by 6-foot wind tunnel. This is a perforated-wall wind tunnel but it does not have acoustic damping material on its walls. The propellers were tested at tunnel through flow Mach numbers of 0.6, 0.7, 0.75, 0.8, and 0.85 with different rotational speeds and blade setting angles. The three propellers, which had approximately the same aerodynamic performance, incorporated different plan forms and different amounts of sweep and yielded different near field noise levels. The acoustically designed propeller had 45 deg of tip sweep and was significantly quieter at M = 0.8 cruise than the straight bladed propeller. The intermediate 30 deg tip sweep propeller, which was swept for aerodynamic purposes, exhibited noise that was between the other two propellers. Noise trends with varying helical tip Mach number and blade loading were also observed.

Dittmar, J. H.↗
NASA NTRS1978

Tone noise of three supersonic helical tip speed propellers in a wind tunnel at 0.8 Mach number

Three supersonic helical tip speed propellers were tested in the NASA Lewis 8- by 6-foot wind tunnel. Noise data were obtained while these propellers were operating at a simulated cruise condition. The walls of this tunnel were not acoustically treated and therefore this was not an ideal location for taking noise data, but it was thought that the differences in noise among the three propellers would be meaningful. The straight bladed propeller which did not incorporate sweep was the noisiest with the aerodynamically swept propeller only slightly quieter. However, the acoustically swept propeller was significantly quieter than the straight propeller, thereby indicating the merit of this design technique.

Dittmar, J. H.↗
NASA NTRS1977

Design and performance of energy efficient propellers for Mach 0.8 cruise

It is believed that a fuel saving of 14 to 40 percent may be realized by the use of an advanced high-speed turboprop. This turboprop must be capable of high efficiency at Mach 0.8 cruise above 9.144 km altitude if it is to compete with turbofan powered commercial aircraft. Several advanced aerodynamic concepts were investigated in recent wind tunnel tests under NASA sponsorship on two propeller models. These concepts included aerodynamically integrated propeller/nacelles, area-ruling, blade sweep, reduced blade thickness and power (disk) loadings several times higher than conventional designs. The aerodynamic design methodology for these models is discussed in this paper. In addition, some of the preliminary test results are presented which indicate that propeller net efficiencies near 80 percent were obtained for high disk loading propellers operating at Mach 0.8.

Mikkelson, D. C.↗
NASA NTRS1977

Design and performance of energy efficient propellers for Mach 0.8 cruise

The increased emphasis on fuel conservation in the world has stimulated a series of studies of both conventional and unconventional propulsion systems for commercial aircraft. Preliminary results from these studies indicate that a fuel saving of 14 to 40 percent may be realized by the use of an advanced high-speed turboprop. This turboprop must be capable of high efficiency at Mach 0.8 cruise above 9.144 km altitude if it is to compete with turbofan powered commercial aircraft. Several advanced aerodynamic concepts were investigated in recent wind tunnel tests under NASA sponsorship on two propeller models. These concepts included aerodynamically integrated propeller/nacelles, area ruling, blade sweep, reduced blade thickness and power (disk) loadings several times higher than conventional designs. The aerodynamic design methodology for these models is discussed. In addition, some of the preliminary test results are presented which indicate that propeller net efficiencies near 80 percent were obtained for high disk loading propellers operating at Mach 0.8.

Mikkelson, D. C.↗
NASA NTRS1976

Boundary layer thickness effect on boattail drag

A combined experimental and analytical program has been conducted at the NASA Lewis Research Center, to investigate the effects of boundary layer changes on the flow over high angle boattail nozzles. The tests were run on an isolated axisymmetric sting mounted model. Various boattail geometries were investigated at high subsonic speeds over a range of boundary layer thicknesses. In general, boundary layer effects were small at speeds up to Mach 0.8. However, at higher speeds significant regions of separated flow were present on the boattail. When separation was present large reductions in boattail drag resulted with increasing boundary layer thickness. The analysis predicts both of these trends.

Blaha, B. J.↗
NASA NTRS1976

Boundary layer thickness effect on boattail drag

A combined experimental and analytical program was conducted to investigate the effects of boundary layer changes on the flow over high angle boattail nozzles. The tests were run on an isolated axisymmetric sting mounted model. Various boattail geometries were investigated at high subsonic speeds over a range of boundary layer thicknesses. In general, boundary layer effects were small at speeds up to Mach 0.8. However, at higher speeds significant regions of separated flow were present on the boattail. When separation was present large reductions in boattail drag resulted with increasing boundary layer thickness. The analysis predicts both of these trends.

Blaha, B. J.↗
NASA NTRS1975

Integration of aft-fuselage-mounted flow through engine nacelles on an advanced transport configuration at Mach numbers from 0.6 to 1.0

An approximately 1/30th-scale model of a CTOL aircraft designed for efficient cruise between Mach 0.9 and 0.98 was tested in the Lewis Research Center's 8- by 6-Foot Supersonic Wind Tunnel. Aft-fuselage axial force and pressure were measured for a series of locally area-ruled engine installations. Two flow-through nacelles with different exit diameters which simulated inlet mass flow ratios of 0.46 and 0.6 (based on maximum nacelle cross-sectional) area were investigated. Both an NACA-1 cowl and a blunter supercritical cowl were tested with these nacelles. Variations in the amount of local area ruling were investigated and an aft fuselage without nacelles was tested for reference. Results observed with flow-through nacelles indicate that efficient cruise may be obtained on this type of aircraft with aft-fuselage-mounted engine nacelles.

Blaha, B. J.↗
NASA NTRS1974

Wind tunnel blockage and support interference effects on winged-body models at Mach numbers from 0.6 to 1.0

Three sting-mounted winged-body models with tunnel blockages of 0.1, 1.0, and 2.0 percent were tested in the Lewis Research Center's 8- by 6- Foot Supersonic Wind Tunnel. Fuselage pressures were obtained over a Mach number range of 0.6 to 1.0 at angles of attack from 0 deg to 4 deg. Two other types of model support were investigated, which included simulated wing-tip and fuselage support-strut mountings. The effects of tunnel porosity and sidewall geometry were also investigated. Model blockage effects were small up to M sub 0 = 0.95. At higher speeds the major blockage effect observed was a displacement of the local transonic terminal shocks on the model. The effects of the wing-tip type of model support were small up to M sub 0 = 0.95, but disturbances were observed on the fuselage at higher speeds. Changes in local tunnel porosity were effective in reducing the disturbances up to M sub 0 = 0.975, but a change in sidewall geometry was not.

Blaha, B. J.↗
NASA NTRS1973

Flight and wind tunnel investigation of the effects of Reynolds number on installed boattail drag at subsonic speeds.

A flight and wind tunnel investigation was conducted to determine the effects of Reynolds number on the installed boattail drag of an underwing nacelle. Tests were run on a modified F-106B aircraft and 0.05 and 0.22 scale wind tunnel models. Tests were conducted at Mach numbers of 0.6 and 0.9 and over a 16 to 1 range of Reynolds numbers. Highest drag was obtained at intermediate Reynolds numbers corresponding to about the lowest flight values and that of the 0.22 scale model. Significantly lower drag was obtained at both higher and lower Reynolds numbers.

Chamberlin, R.↗
NASA NTRS1972

Flight and wind tunnel investigation of the effects of Reynolds number on installed boattail drag at subsonic speeds

A flight and wind tunnel investigation was conducted to determine the effects of Reynolds number on the installed boattail drag of an underwing nacelle. Tests were run on a modified F-106B aircraft and 0.05 and 0.22 scale wind tunnel models. Tests were conducted at Mach numbers of 0.6 and 0.9 and over a 16 to 1 range of Reynolds numbers. Highest drag was obtained at intermediate Reynolds numbers corresponding to about the lowest flight values and that of the 0.22 scale model. Significantly lower drag was obtained at both higher and lower Reynolds numbers.

Chamberlin, R.↗