Search NASA⌕ Search

Engineering topics

Blankenship, C. P.

Publications and source records attributed to Blankenship, C. P..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Tough composite materials: Recent developments

The present volume broadly considers topics in composite fracture toughness and impact behavior characterization, composite system constituent properties and their interrelationships, and matrix systems' synthesis and characterization. Attention is given to the characterization of interlaminar crack growth in composites by means of the double cantilever beam specimen, the characterization of delamination resistance in toughened resin composites, the effect of impact damage and open holes on the compressive strength of tough resin/high strain fiber laminates, the effect of matrix and fiber properties on compression failure mechanisms and impact resistance, the relation of toughened neat resin properties to advanced composite mechanical properties, and constituent and composite properties' relationships in thermosetting matrices. Also treated are the effect of cross-link density on the toughening mechanism of elastomer-modified epoxies, the chemistry of fiber/resin interfaces, novel carbon fibers and their properties, the development of a heterogeneous laminating resin, solvent-resistant thermoplastics, NASA Lewis research in advanced composites, and opportunities for the application of composites in commercial aircraft transport structures.

Vosteen, L. F.↗
NASA NTRS1982

Materials technology for large space structures

Several of the key material technology needs that were identified for large space structures are outlined. They include lightweight structural materials, materials durability in the space environment, and some special aspects of materials fabrication technology. Examples of current materials research directed toward large space structures are described. Additional research needs and opportunities are noted. A short bibliography is included of selected references that describe large space structural concepts and related technology needs in detail.

Blankenship, C. P.↗
NASA NTRS1978

Advanced materials research for long-haul aircraft turbine engines

The status of research efforts to apply low to intermediate temperature composite materials and advanced high temperature materials to engine components is reviewed. Emerging materials technologies and their potential benefits to aircraft gas turbines were emphasized. The problems were identified, and the general state of the technology for near term use was assessed.

Signorelli, R. A.↗
NASA NTRS1977

Tantalum modified ferritic iron base alloys

Strong ferritic alloys of the Fe-CR-Al type containing 0.4% to 2% tantalum were developed. These alloys have improved fabricability without sacrificing high temperature strength and oxidation resistance in the 800 C (1475 F) to 1040 C (1900 F) range.

Oldrieve, R. E.↗
NASA NTRS1977

Opportunities for ceramics in the ERDA/NASA continuous combustion propulsion systems program

An overview on engine development projects for potential use of ceramics is reported. A major ceramics materials technology effort is described to meet anticipated engine system requirements in terms of the automotive application, some of the more pressing technology needs, and some indications of how to conduct this technology program with industry-engine development projects focus on both gas turbine and Stirling engines.

Blankenship, C. P.↗
NASA NTRS1977

Opportunities for ceramics in the ERDA/NASA Continuous Combustion Propulsion Systems Program

The ERDA/NASA Continuous Combustion Highway Vehicles Program is concerned with the development of improved automotive powerplants. Specific program goals are related to an achievement of an improved fuel economy, low emissions, multifuel capability, and marketability. An employment of high temperature ceramic materials is considered in connection with the development of improved gas turbine and Stirling engines. The ceramic materials technology project is discussed, taking into account the characterization of ceramic materials, improved ceramic materials, and questions of component design, fabrication, and testing.

Blankenship, C. P.↗
NASA NTRS1975

Trends in high temperature materials technology for advanced aircraft turbine engines

The utilization of high temperature materials for turbine blades, disks, vanes, and combustors is reviewed. The use of directionally solidified eutectic alloys and of metal fiber reinforced superalloys as turbine blade materials is discussed. The application of powder metallurgy to the production of turbine disks is considered. It is shown that oxide-dispersion strengthened alloys (including NiCr and NiCr-Al) and ceramics are the best refractory turbine vane materials. The use of heat resistant sheet alloys as combustor materials is examined. The cost benefits to be derived from the application of high temperature technology to advanced CTOL and STOL engines are described.

Blankenship, C. P.↗
NASA NTRS1974

Design and evaluation of experimental ceramic automobile thermal reactors

The results obtained in an exploratory evaluation of ceramics for automobile thermal reactors are summarized. Candidate ceramic materials were evaluated in several reactor designs by using both engine-dynamometer and vehicle road tests. Silicon carbide contained in a corrugated-metal support structure exhibited the best performance, lasting 1100 hr in engine-dynamometer tests and more than 38,600 km (24000 miles) in vehicle road tests. Although reactors containing glass-ceramic components did not perform as well as those containing silicon carbide, the glass-ceramics still offer good potential for reactor use with improved reactor designs.

Stone, P. L.↗
NASA NTRS1974

Evaluation of alloys and coatings for use in automobile thermal reactors

Several candidate alloys and coatings were evaluated for use in automobile thermal reactors. Full-size reactors of the candidate materials were evaluated in cyclic engine dynamometer tests with a peak temperature of 1040 C (1900 F). Two developmental ferritic-iron alloys, GE-1541 and NASA-18T, exhibited the best overall performance by lasting at least 60 percent of the life of test engine. Four of the alloys evaluated warrant consideration for reactor use. They are GE-1541, Armco 18 SR, NASA-18T, and Inconel 601. None of the commercial coating substrate combinations evaluated warrant consideration for reactor use.

Blankenship, C. P.↗
NASA NTRS1974

An evaluation of alloys and coatings for use in automobile thermal reactors

Several candidate alloys and coatings were evaluated for use in automobile thermal reactors. Full-size reactors of the candidate materials were analyzed in cyclic engine dynamometer tests with peak temperature of 1900 F (1040 C). Two developmental ferritic iron alloys GE1541 and NASA-18T - exhibited the best overall performance lasting at least 60% of the life of the test engine. Four of the alloys evaluated warrant consideration for reactor use. They include GE1541, Armco 18 SR, NASA-18T, and Inconel 601. None of the commercial coating substrate combinations evaluated warrant consideration for reactor use.-

Blankenship, C. P.↗
NASA NTRS1974

Design and evaluation of experimental ceramic automobile thermal reactors

The paper summarizes the results obtained in an exploratory evaluation of ceramics for automobile thermal reactors. Candidate ceramic materials were evaluated in several reactor designs using both engine dynamometer and vehicle road tests. Silicon carbide contained in a corrugated metal support structure exhibited the best performance, lasting 1100 hours in engine dynamometer tests and for more than 38,600 kilimeters (24,000 miles) in vehicle road tests. Although reactors containing glass-ceramic components did not perform as well as silicon carbide, the glass-ceramics still offer good potential for reactor use with improved reactor designs.

Stone, P. L.↗
NASA NTRS1972

Development of dispersion-strengthened Ni-Cr-ThO2 alloys for the space shuttle thermal protection system.

An improved manufacturing process has been developed for TD-NiCr that provides sheet of improved quality, better gage control, and reproducible properties. A standard manufacturing process has been developed for the alternate alloy, DS-NiCr, produced by pack-chromizing Ni-2ThO2 sheet. Extension of forming and joining technology for TD-NiCr is in process. Formability criteria are being established for basic sheet forming processes related to the manufacture of Shuttle TPS panels. They include brake forming, corrugation forming, joggling, dimpling, and beading. Joining processes applicable to TPS panels are being optimized with emphasis on establishment of joint efficiencies. Resistance spot welding (fusion and solid state), resistance seam welding, solid-state diffusion welding, and brazing are included in the joining programs. Development of improved manufacturing technology for TD-NiCr fasteners is also being accomplished. Mechanical and physical properties of TD-NiCr are being characterized to provide design-allowable data.

Blankenship, C. P.↗
NASA NTRS1972

NASA-EPA automotive thermal reactor technology program

The status of the NASA-EPA automotive thermal reactor technology program is summarized. This program is concerned primarily with materials evaluation, reactor design, and combustion kinetics. From engine dynamometer tests of candidate metals and coatings, two ferritic iron alloys (GE 1541 and Armco 18-SR) and a nickel-base alloy (Inconel 601) offer promise for reactor use. None of the coatings evaluated warrant further consideration. Development studies on a ceramic thermal reactor appear promising based on initial vehicle road tests. A chemical kinetic study has shown that gas temperatures of at least 900 K to 1000 K are required for the effective cleanup of carbon monoxide and hydrocarbons, but that higher temperatures require shorter combustion times and thus may permit smaller reactors.

Blankenship, C. P.↗
NASA NTRS1972

Development of dispersion-strengthened Ni-Cr-ThOz alloys for the space shuttle thermal protection system

Manufacturing processes were developed for TD-NiCr providing small sheet (45 x 90 cm), and larger sheet (60 x 150 cm) and foil. The alternate alloy, DS-NiCr, was produced by pack-chromizing Ni-ThO2 sheet. Formability criteria are being established for basic sheet forming processes, which are brake forming, corrugation forming, joggling, dimpling, and beading. Resistance spot welding (fusion and solid state), resistance seam welding, solid state diffusion welding, and brazing are included in the joining programs. Major emphasis is centered on an Al-modified Ni-Cr-ThO2 alloy development. These alloys, containing 3 to 5% Al, form the protective Al2O3 scale. This enhances oxidation resistance under reentry conditions. Both TD-NiCrAl and DS-NiCrAl alloys are included. A tentative composition of Ni-16Cr-3.5Al-2ThO2 was selected based on oxidation resistance and fabricability.

Blankenship, C. P.↗
NASA NTRS1972

Exploratory evaluation of ceramics for automobile thermal reactors

An exploratory evaluation of ceramics for automobile thermal reactors was conducted. Potential ceramic materials were evaluated in several reactor designs using both engine dynamometer and vehicle road tests. Silicon carbide contained in a corrugated metal support structure exhibited the best performance lasting over 800 hours in engine dynamometer tests and over 15,000 miles (24,200 km) of vehicle road tests. Reactors containing glass-ceramic components did not perform as well as silicon carbide. But the glass-ceramics still offer good potential for reactor use. The results of this study are considered to be a reasonable demonstration of the potential use of ceramics in thermal reactors.

Stone, P. L.↗