Search NASA⌕ Search

Engineering topics

Blonski, Slawomir

Publications and source records attributed to Blonski, Slawomir.

51 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS2002

Measurement Sets and Sites Commonly used for Characterizations

Scientists with NASA's Earth Science Applications Directorate are creating a well-characterized Verification & Validation (V&V) site at the Stennis Space Center (SSC). This site enables the in-flight characterization of remote sensing systems and the data that they require. The data are predominantly acquired by commercial, high-spatial resolution satellite systems, such as IKONOS and QuickBird 2, and airborne systems. The smaller scale of these newer high-resolution remote sensing systems allows scientists to characterize the geometric, spatial, and radiometric data properties using a single V&V site. The targets and techniques used to characterize data from these newer systems can differ significantly from the earlier, coarser spatial resolution systems. Scientists are also using the SSC V&V site to characterize thermal infrared systems and active Light Detection and Ranging (LIDAR) systems. SSC employs geodetic targets, edge targets, radiometric tarps, and thermal calibration ponds to characterize remote sensing data products. This paper presents a proposed set of required measurements for visible-through-longwave infrared remote sensing systems, and a description of the Stennis characterization. Other topics discussed inslude: 1) use of ancillary atmospheric and solar measurements taken at SSC that support various characterizations, 2) other sites used for radiometric, geometric, and spatial characterization in the continental United States,a nd 3) the need for a standardized technique to be adopted by the Committee on Earth Observation Satellites (CEOS) and other organizations.

Pagnutti, Mary↗
NASA NTRS2002

Comparing IKONOS and Landsat 7 Images

This work is a continuation of the simulations presented at the previous workshop.INformation is presented on the following: 20 IKONOS images compared with 10 Landsat 7 ETM+VNIR images acquired on the same days. Comparisons are based on simulations of the Landsat 7 images from the IKONOS data. IKONOS and Landsat 7 images used in simulations are on a similar processing level with radiometric correction, georeferenced with cubic-convolution resampling, and UTM projection with WGS-84 datum.

Blonski, Slawomir↗
NASA NTRS2001

In-Flight Edge Response Measurements for High Spatial Resolution Remote Sensing Systems

In-flight measurement of spatial resolution were conducted as part of the ASA Scientific Data Purchase (SDP) Validation and Verification (V&V) process. Characterization included remote sensing systems with ground sample distance (GSD) of 1 meter or less, such as the panchromatic imager on-board the ICONOS satellite and the airborne ADAR System 5500 multispectral instrument. Final image products were used to evaluate the effect of both the image acquisition system (e.g., optics, electronics, motion, jitter, atmosphere) and image post-processing (e.g., resampling, modulation trasfer function (MTF) compensator). Spatial resolution was characterized by full width at half maximum (FWHM) of an edge response-derived line spread function. This was found to be a more robust measure of spatial resolution than the value of NTF at Nyquist frequency The edge responses were analysed using the tilted-edge technique that ovecomes the spatial sampling limitations of the digital imaging systems. As an enhancement to existing algorithms, the slope of the edge response and the orientation of the edge target were determined by a single computational process. Adjacent black and white square panels, either painted on a flat surface or deployed as traps, formed the ground-based edge targets used in the tests. Orientation of the deployable tarps was optimized beforehand, based on simulations of the imaging system. Numerous edge target images were analyzed for each of the tested sensors. The effect of such factors as acquisition geometry, temporal variability, MTF compensation, and GSD on spatial resolution were investigated.

Blonski, Slawomir↗
NASA NTRS2001

An Approach to Application of Multispectral Sensors, using AVIRIS Data

High spatial resolution multispectral/hyperspectral sensors are being developed by private industry with science/research customers as end users. With an increasingly wide range of sensor choices, it is important for the remote sensing science community and commercial community alike to understand the trade-offs between ground sample distance (GSD), spectral resolution, and signal-to-noise ratio (SNR) in selecting a sensor that will best meet their needs. High spatial resolution hyperspectral imagery and super resolution multispectral charge-coupled device imagery can be used to develop prototypes of proposed data acquisition systems without building new systems or collecting large sets of additional data. By using these datasets to emulate proposed and existing systems, imaging systems may be optimized to meet customer needs in a virtual environment. This approach also enables one to determine, a priori, whether an existing dataset will be useful for a given application.

Warner, Amanda↗
NASA NTRS2001

An Approach to Application Validation of Multispectral Sensors Using AVIRIS

High-resolution multispectral data are becoming widely available for commercial and scientific use. For specific applications, such as agriculture studies, there is a need to quantify the performance of such systems. In many cases, parameters such as GSD and SNR can be optimized. Data sets with varying GSD's for the Landsat ETM+ bands were produced to evaluate the effects of GSD on various algorithms and transformations, such as NDVI, principal component analysis, unsupervised classification, and mixture analysis. By showing that AVIRIS data can be used to simulate spaceborne and airborne multispectral platforms over a wide range of GSD, this research can be used to assist in band selection and spatial resolution specifications for new sensors and in optimization of acquisition strategies for existing multispectral systems.

Warner, Amanda↗
NASA NTRS2001

LDCM Preliminary Thermal Trades

The expected cost of adding thermal bands to the next generation Landsat Data Continuity Mission (LDCM) could be significant. This viewgraph presentation investigates both traditional cooled cross-track scanners and new architectures (cooled and uncooled) which could enable a low cost thermal capability. The presentation includes surveys of applications of Landsat thermal data and the architecture of thermal instruments. It also covers new thermal architecture sensor trades, ALI Architecture with Uncooled TIR Detectors, and simulated thermal imagery.

Ryan, Robert↗
NASA NTRS1999

Satellite Hyperspectral Imaging Simulation

Simulation of generic pushbroom satellite hyperspectral sensors have been performed to evaluate the potential performance and validation techniques for satellite systems such as COIS(NEMO), Warfighter-1(OrbView-4) and Hyperion(EO-1). The simulations start with a generation of synthetic scenes from material maps of studied terrain. Scene-reflected radiance is corrected for atmospheric effects and convolved with sensor spectral response using MODTRAN 4 radiance and transmissions calculations. Scene images are further convolved with point spread functions derived from Optical Transfer Functions (OTF's) of the sensor system. Photon noise and etectorr/electronics noise are added to the simulated images, which are also finally quantized to the sensor bit resolution. Studied scenes include bridges and straight roads used for evaluation of sensor spatial resolution, as well as fields of minerals, vegetation and manmade materials used for evaluation of sensor radiometric response and sensitivity. The scenes are simulated with various seasons and weather conditions. Signal-to-noise ratios and expected performance are estimated for typical satellite system specifications and are discussed for all the scenes.

Zanoni, Vicki↗
NASA NTRS1999

Synthetic Scene Generation of the Stennis V and V Target Range for the Calibration of Remote Sensing Systems

The verification and validation (V&V) target range developed at Stennis Space Center is a useful test site for the calibration of remote sensing systems. In this paper, we present a simple algorithm for generating synthetic radiance scenes or digital models of this target range. The radiation propagation for the target in the solar reflective and thermal infrared spectral regions is modeled using the atmospheric radiative transfer code MODTRAN 4. The at-sensor, in-band radiance and spectral radiance for a given sensor at a given altitude is predicted. Software is developed to generate scenes with different spatial and spectral resolutions using the simulated at-sensor radiance values. The radiometric accuracy of the simulation is evaluated by comparing simulated with AVIRIS acquired radiance values. The results show that in general there is a good match between AVIRIS sensor measured and MODTRAN predicted radiance values for the target despite the fact that some anomalies exist. Synthetic scenes provide a cost-effective way for in-flight validation of the spatial and radiometric accuracy of the data. Other applications include mission planning, sensor simulation, and trade-off analysis in sensor design.

Cao, Chang-Yong↗
NASA NTRS1999

NASA's Virtual Product Laboratory: An Overview

The Virtual Product Laboratory (VPL) developed by NASA's Commercial Remote Sensing Program at the John C. Stennis Space Center is a tool that enables simulation, design, and verification of remote sensing systems within a software (virtual) environment. The VPL can serve industry, government, and university communities by providing a means to conduct system trade studies, optimization, visual modeling, and data product simulations entirely in a virtual environment. The VPL can serve as a complete end-to-end simulation tool capable of producing system and subsystem performance characterizations, system optimization, and simulated data products or as a means of evaluating any one component of a remote sensing system. In this paper, we present an overview of the VPL capabilities. The VPL functional areas include Requirements, Design & Analysis, Simulation, Project Management, Knowledge Base, and Help. A description of each function along with the tools and techniques used to accomplish these functions will be provided. When possible, sample VPL displays and products will be used in the presentation.

Gasser, Jerry↗
NASA NTRS1999

Hyperspectral Thermal Fabry-Perot Modeling

Fabry-Perot interferometer are simple elegant, tunable filters that can be used to make compact hyperspectral thermal imaging system. To foster the development of these sensors, software tools for the design and simulation of tunable Fabry-Perot infrared imagers have been developed. The tools are provided at three levels: basic, design, and system. Basic tools describe a nearly ideal Fabry-Perot filter with perfectly flat and parallel mirrors in collimated space. Design tools that take into account non-ideal behavior such as mirror and collimation defects calculate free spectral range, finesse, and spectral width of the interferometer. System tools help analyze an integration of the Fabry-Perot filter into a camera system. They include spectral convolution, first-order optical layout, and an estimation of signal-to-noise ratio. The complete set of tools allows for simulations of system operation and performance with various illumination sources. Spectral images generated in such simulations were used to examine applicability of Fabry-Perot system in remote sensing of atmospheric gases including detection of environmental pollutants and hazardous gases. Different operating conditions and system configurations are presented.

Ryan, Robert↗
NASA NTRS1999

NASA's Virtual Product Laboratory Overview

The Virtual Product Laboratory (VPL) developed at Stennis Space Center is a tool that enables design and verification of remote sensing systems within a software (virtual) environment. The VPL can serve NASA's industry, government, and university partners by providing a means to conduct system trade studies, visual modeling, and data product simulations entirely in a virtual environment. The VPL can serve as a complete end-to-end simulation tool capable of producing system-level compatability assessments, performance characterizations, and simulated data products. In this paper, we present an overview of the VPL's current functions and planned capabilities. The VPL functional areas include Requirements, Design and Analysis, Simulation, Project Management, and Knowledge Base. A description of each function, along with the tools and techniques used to accomplish these functions, is provided.

Gasser, Gerald↗
NASA NTRS1999

Spatial Resolution Determination with the Stennis Edge Target and NIIRS

Methodologies for determining the modulation transfer function (MTF) and National Imagery Interpretability Rating Scale (NIIRS) of airborne panchromatic and multispectral digital imaging cameras using the NASA Stennis Space Center (SSC) edge target have been developed. The application of NIIRS for determining the relative utility of data sets against various applications is discussed. Sampling requirements and optimal flightlines for focal plane imagers have been investigated. It is shown that with sufficient flight tilt angle, an adequate number of samples can be obtained to define the edge response accurately. The relationships between the tilt angle, Ground Sample Distance (GSD), and the number of samples are discussed. Sample results using commercially available data and the NASA SSC edge target are presented and compared to theoretical results.

Ryan, Robert↗
NASA NTRS1999

Satellite Hyperspectral Imaging Simulation

Simulations of generic pushbroom satellite hyperspetral sensors have been performed to evaluate the potential performance and validation techniques for satellite systems such as COIS (NEMO), Warfighter-1 (OrbView-4), and Hyperion (EO-1). The simulaitons start with a generation of synthetic scenes form material maps of studied terrain. Scene-reflected radiance is corrected for atmospheric effects and convolved with sensor spectral response uwing MODTRAN 4 radiance and transmission calculations. Scene images are further convolved with point spread functions derived from Optical Transfer Functions (OTF's) of the sensor system. Photon noise and detector/electronics noise are added to the simulated images, which are also finally quantized to the sensor bit resolution. Studied scenes include bridges and straight roads used for evaluation of sensor spatial resolution, as well as fields of minerals, vegetation, and manmade materials used for evaluation of sensor radiometric response and sensitivity. The scenes are simulated with various seasons and weather conditions. Signal-to-noise ratos and expected performance are estimated for typica satellite system specifications and are discussed for all the scenes.

Zanoni, Vicki↗
NASA NTRS1999

Synthetic Scene Generation of Stennis Target Range for the Calibration of Remote Sensing Systems

The validation and verification (V&V) target range developed at Stennis Space Center is a useful tool for the calibration of remote sensing systems. In this paper, we present an algorithm for generating synthetic scenes or digital models of this target range. The atmospheric radiative transfer code Modtran 4 is used in simulating at-sensor radiance for a given sensor. Software is developed to generate the scene with different spatial and spectral resolutions using the at-sensor radiance values. Synthetic scenes provide a cost-effective way for in-flight validation for the spatial and radiometric accuracy of the data. Other applications include mission planning, sensor simulation, and trade-off analysis in sensor design. The radiometric and spatial accuracy of the simulation is evaluated by comparing simulated scenes with AVIRIS acquired values.

Cao, Chang-Yong↗