Engineering topics

Bobek, Michael

Publications and source records attributed to Bobek, Michael.

11 records

DOE OSTI2024

Design, Fabrication, and testing of Direct Air Capture Sorbent modules to increase understanding of trade-offs in pressure drop and capture efficiency

Conference presentation for the work entitled “Design, Fabrication, and testing of Direct Air Capture Sorbent modules to increase understanding of trade-offs in pressure drop and capture efficiency”. In recent years, there has been a growing interest in Direct Air Capture (DAC) of CO2. This technology is gaining attention as a method to enhance the reduction of atmospheric greenhouse gases (GHGs), particularly when used alongside other decarbonization strategies. The route for efficient and net carbon negative DAC is challenging because CO2 in the atmosphere is highly diluted (~400ppm). This work, utilizing 3D printing capabilities for rapid prototyping, presents application-based findings on the design, fabrication, and testing of DAC module form factors that house solid sorbents. The work leverages an experimental rig that can achieve air throughput and velocities approaching that which are anticipated for commercial scales. The tradeoffs of pressure drop, footprint and capture efficiency are discussed for different orientations of a NETL patented sorbent material.

Riley, Jarrett↗

DOE OSTI2023

Investigation of methane and ethane pyrolysis with highly active and durable iron-alumina catalyst to produce hydrogen and valuable nano carbons: Continuous fluidized bed tests and reaction rate analysis

The goal of this research work was to evaluate a novel iron-alumina catalyst for methane and ethane pyrolysis with high conversion rates to H 2 with a long life time to address two major issues reported with previous catalysts. Fluidized bed tests demonstrated continuous hydrogen production while collecting carbon containing fines. During the 230 h fluid bed test the methane conversion rate to hydrogen at 700 °C remained above 80% for 160 h while creating valuable nano carbons. Similarly high catalyst lifetimes with high methane conversions have not been reported before. Ethane was more active than methane for pyrolysis with 100% conversion to H 2 . Transmission electron microscopy and Raman analysis of the carbon showed single and multiwall nanotubes and conglomerate nano-fibers. Ethane did not impact the allotrope of carbon formed. TGA was used to create a data array that was used for kinetic analysis and reaction model parametric regressions. Ethane had a higher rate of pyrolysis that was 2.3–2.8 times that of methane. Ethane pyrolysis was found to be more sensitive to temperature with a higher activation energy of 62 kJ/mol as compared to methane at 43 kJ/mol. The frequency factor, A i , was significantly higher for ethane at 0.73 [[kmol/m 3 -sec]/[N/m2] n ] compared to 0.03 for methane on the same basis. Both gases had a functional partial pressure order dependence of ~0.6 based on the regression analysis.

08 HYDROGEN↗

DOE OSTI2021

Development of CuFeMnAlO 4+δ oxygen carrier with high attrition resistance and 50-kWth methane/air chemical looping combustion tests

A Copper-Ferri-Manganese-Aluminate spinel (CuFeMnAlO 4+δ ) oxygen carrier, developed at the US Department of Energy’s (DOE) National Energy Technology Laboratory (NETL), shows promising results for chemical looping combustion with methane. Attrition resistance of the spinel oxygen carrier (160–600 µm) produced by a wet agglomeration method was significantly higher than that observed previously with a Copper-Ferri-Aluminate (CuFeAlO 4 ) oxygen carrier. Improved attrition resistance of the novel carrier can be attributed to minimal alumina phase segregation and minimal carbon formation. Heats of reaction measured by differential scanning calorimetry indicated exothermicity during reduction with methane. The total oxygen transfer capacity of the material was about 10.5 wt% at 850 °C. The attrition resistance and the oxygen transfer capacity of the carrier prepared at a commercial manufacturing facility (180 kg) were very similar to observed values during the development phase with the lab scale preparations. The material displays satisfactory methane conversion and significantly high particle durability during a 54 h test campaign conducted in NETL’s 50-kWth chemical looping dual fluid bed reactor unit at temperatures ranging from 700 to 900 °C. Low oxygen carrier make-up cost, due to the use of natural ore and pigment grade raw materials during synthesis and very low attrition rates, exceeded the performance goals determined by systems studies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Final Report – Cooperative Research and Development Agreement between National Energy Technology Laboratory and Praxair, Inc.

Praxair and DOE-NETL entered into a collaborative research and development agreement (CRADA) in March 2019 to evaluate economic viability of chemical looping processes for hydrogen, CO, and syngas production in comparison to state-of-the-art conventional processes. Praxair had developed process configurations for producing hydrogen and CO using chemical looping processes. NETL had modeling and system design experience for the chemical looping reactor system. The goal for NETL is to provide performance and design information regarding the chemical looping portion of a potential commercial plant. Praxair’s goal is to evaluate chemical looping processes and try to identify a process that can be commercially relevant within a few years. A key to success for the program will be to develop a chemical looping reactor system that enables significant capital cost reduction and performance improvement for the overall process. This report describes chemical looping-based CO production process, chemical looping reactor system and oxygen carrier material as well as summary of technoeconomic analysis results. Also included in the report are a list of assumptions that were used for designing the chemical looping plant and a list of areas for further study required to validate some of these assumptions in future efforts. The initial goal was to design two chemical looping plants. Case 1 would produce 1 MM scfd Hydrogen from NG, and Case 2 would co-produce hydrogen and 5 MM scfd CO from NG. However, later in the collaboration, it was decided to drop Case 1 as Case 2 process already included hydrogen production.

Bayham, Samuel↗

DOE OSTI2018