Search NASA⌕ Search

Engineering topics

Boebinger, Matthew G.

Publications and source records attributed to Boebinger, Matthew G..

18 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Iron Impurity Impairs the CO 2 Capture Performance of MgO: Insights from Microscopy and Machine Learning Molecular Dynamics

Magnesium oxide (MgO) is a promising sorbent for direct air capture (DAC) of carbon dioxide. Iron (Fe) is a common impurity in naturally occurring MgO and minerals used to produce MgO, yet a molecular-scale understanding of Fe-doping effects on carbonation is lacking. Here, in this study, we observed reduced carbonation performance in Fe-doped MgO experimentally. The energetics of adsorbing a (bi)carbonate ion on pristine and Fe-doped MgO(001) surfaces were further investigated using ab initio and machine learning potential molecular dynamics coupled with metadynamics simulations. Both pristine and Fe-doped surfaces exhibited a basic (OH – ) hydration layer, where the (bi)carbonate ion adsorption is thermodynamically favorable. However, the dissolution of surface Fe had smaller energy barriers and was more favorable than Mg. Leached Fe likely neutralized the near-surface basicity, yielding reduced reactivity on Fe-doped MgO. Our observations offer critical insights for material selection and emphasize the importance of evaluating the geologic origin of earth materials used for DAC.

36 MATERIALS SCIENCE↗
DOE OSTI2024

One-Pot Self-Assembly of Sequence-Controlled Mesoporous Heterostructures via Structure-Directing Agents

Multimaterial heterostructures have led to characteristics surpassing the individual components. Nature controls the architecture and placement of multiple materials through biomineralization of nanoparticles (NPs); however, synthetic heterostructure formation remains limited and generally departs from the elegance of self-assembly. Here, in this study, a class of block polymer structure-directing agents (SDAs) are developed containing repeat units capable of persistent (covalent) NP interactions that enable the direct fabrication of nanoscale porous heterostructures, where a single material is localized at the pore surface as a continuous layer. This SDA binding motif (design rule 1) enables sequence-controlled heterostructures, where the composition profile and interfaces correspond to the synthetic addition order. This approach is generalized with 5 material sequences using an SDA with only persistent SDA-NP interactions (“P-NP 1 –NP 2 ”; NP i = TiO 2 , Nb 2 O 5 , ZrO 2 ). Expanding these polymer SDA design guidelines, it is shown that the combination of both persistent and dynamic (noncovalent) SDA-NP interactions (“PD-NP 1 –NP 2 ”) improves the production of uniform interconnected porosity (design rule 2). The resulting competitive binding between two segments of the SDA (P- vs D-) requires additional time for the first NP type (NP 1 ) to reach and covalently attach to the SDA (design rule 3). The combination of these three design rules enables the direct self-assembly of heterostructures that localize a single material at the pore surface while preserving continuous porosity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Alkali cation stabilization of defects in 2D MXenes at ambient and elevated temperatures

Transition metal carbides have been adopted in energy storage, conversion, and extreme environment applications. Advancements in their 2D counterparts, known as MXenes, enable the design of unique structures at the ~1 nm thickness scale. Alkali cations have been essential in MXenes manufacturing processing, storage, and applications, however, exact interactions of these cations with MXenes are not fully understood. In this study, using Ti 3 C 2 T x , Mo 2 TiC 2 T x , and Mo 2 Ti 2 C 3 T x MXenes, we present how transition metal vacancy sites are occupied by alkali cations, and their effect on MXene structure stabilization to control MXene’s phase transition. We examine this behavior using in situ high-temperature x-ray diffraction and scanning transmission electron microscopy, ex situ techniques such as atomic-layer resolution secondary ion mass spectrometry, and density functional theory simulations. In MXenes, this represents an advance in fundamentals of cation interactions on their 2D basal planes for MXenes stabilization and applications. Broadly, this study demonstrates a potential new tool for ideal phase-property relationships of ceramics at the atomic scale.

42 ENGINEERING↗
DOE OSTI2024

Lithiation Induced Phases in 1T'-MoTe 2 Nanoflakes

Multiple polytypes of MoTe 2 with distinct structures and intriguing electronic properties can be accessed by various physical and chemical approaches. Here, in this study, we report electrochemical lithium (Li) intercalation into 1T'-MoTe 2 nanoflakes, leading to the discovery of two previously unreported lithiated phases. Distinguished by their structural differences from the pristine 1T' phase, these distinct phases were characterized using in situ polarization Raman spectroscopy and in situ single-crystal X-ray diffraction. The lithiated phases exhibit increasing resistivity with decreasing temperature, and their carrier densities are two to 4 orders of magnitude smaller than the metallic 1T' phase, as probed through in situ Hall measurements. The discovery of these gapped phases in initially metallic 1T'-MoTe 2 underscores electrochemical intercalation as a potent tool for tuning the phase stability and electron density in two-dimensional (2D) materials.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Direct Fabrication of Atomically Defined Pores in MXenes Using Feedback-Driven STEM

Controlled fabrication of nanopores in 2D materials offer the means to create robust membranes needed for ion transport and nanofiltration. Techniques for creating nanopores have relied upon either plasma etching or direct irradiation; however, aberration-corrected scanning transmission electron microscopy (STEM) offers the advantage of combining a sub-Å sized electron beam for atomic manipulation along with atomic resolution imaging. Here, for this work, a method for automated nanopore fabrication is utilized with real-time atomic visualization to enhance the mechanistic understanding of beam-induced transformations. Additionally, an electron beam simulation technique, Electron-Beam Simulator (E-BeamSim) is developed to observe the atomic movements and interactions resulting from electron beam irradiation. Using the MXene Ti 3 C 2 T x , the influence of temperature on nanopore fabrication is explored by tracking atomic transformations and find that at room temperature the electron beam irradiation induces random displacement and results in titanium pileups at the nanopore edge, which is confirmed by E-BeamSim. At elevated temperatures, after removal of the surface functional groups and with the increased mobility of atoms results in atomic transformations that lead to the selective removal of atoms layer by layer. This work can lead to the development of defect engineering techniques within functionalized MXene layers and other 2D materials.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Epitaxial Metal Electrodeposition Controlled by Graphene Layer Thickness

Control over material structure and morphology during electrodeposition is necessary for material synthesis and energy applications. One approach to guide crystallite formation is to take advantage of epitaxy on a current collector to facilitate crystallographic control. Single-layer graphene on metal foils can promote “remote epitaxy” during Cu and Zn electrodeposition, resulting in growth of metal that is crystallographically aligned to the substrate beneath graphene. However, the substrate–graphene–deposit interactions that allow for epitaxial electrodeposition are not well understood. Here, we investigate how different graphene layer thicknesses (monolayer, bilayer, trilayer, and graphite) influence the electrodeposition of Zn and Cu. Scanning transmission electron microscopy and electron backscatter diffraction are leveraged to understand metal morphology and structure, demonstrating that remote epitaxy occurs on mono- and bilayer graphene but not trilayer or thicker. Density functional theory (DFT) simulations reveal the spatial electronic interactions through thin graphene that promote remote epitaxy. This work advances our understanding of electrochemical remote epitaxy and provides strategies for improving control over electrodeposition.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Dry Printing Pure Copper with High Conductivity and Adhesion for Flexible Electronics

Additive manufacturing of functional devices on various rigid and flexible substrates is rising rapidly due to their design flexibility, rapid manufacturing, and lower cost. Current printing technologies are ink-based and focused on printing silver (Ag) as conductive lines due to its matured ink formulation process, low sintering temperature, ease of printing, and low oxidation rate. However, Ag is the 68th most abundant element on Earth, while copper (Cu) is the 25th, making it much cheaper (>100×) while having a comparable conductivity to Ag. Therefore, printing Cu has become technologically and economically more attractive than Ag. Nevertheless, Cu printing is still a significant challenge in ink-based printing methods due to the higher sintering temperature relative to the glass-transition temperature of most flexible substrates, the higher oxidation rate, the challenging ink formulation process, and ink stability concerns. Here, we demonstrate printing highly conductive Cu on flexible polyimide substrates using a dry printing technique. Cu nanoparticles (~3–30 nm) are generated by on-demand laser ablation of a solid Cu target inside the printer head and under argon background gas. These Cu nanoparticles are then transported through a nozzle and onto the substrate, where they are laser-sintered in real time. The argon gas plays three critical roles in laser plume condensation for nanoparticle generation, transport, and sheath gas to avoid oxidation during sintering. The sintered nanoparticles thus show high electrical conductivity and mechanical stability under static and cyclic tests. Our dry printing technique can potentially revolutionize how electronic devices and sensors are additively manufactured for earth and space applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Reaction Layer Formation on MgO in the Presence of Humidity

Mineralization by MgO is an attractive potential strategy for direct air capture (DAC) of CO 2 due to its tendency to form carbonate phases upon exposure to water and CO 2 . Hydration of MgO during this process is typically assumed to not be rate limiting, even at ambient temperatures. However, surface passivation by hydrated phases likely reduces the CO 2 capture capacity. Here, we examine the initial hydration reactions that occur on MgO(100) surfaces to determine whether they could potentially impact CO 2 uptake. We first used atomic force microscopy (AFM) to explore changes in reaction layers in water (pH = 6 and 12) and MgO-saturated solution (pH = 11) and found the reaction layers on MgO are heterogeneous and nonuniform. To determine how relative humidity (R.H.) affects reactivity, we reacted samples at room temperature in nominally dry N 2 (~11–12% R.H.) for up to 12 h, in humid (>95% R.H.) N 2 for 5, 10, and 15 min, and in air at 33 and 75% R.H. for 8 days. X-ray reflectivity and electron microscopy analysis of the samples reveal that hydrated phases form rapidly upon exposure to humid air, but the growth of the hydrated reaction layer slows after its initial formation. Reaction layer thickness is strongly correlated with R.H., with denser reaction layers forming in 75% R.H. compared with 33% R.H. or nominally dry N 2 . The reaction layers are likely amorphous or poorly crystalline based on grazing incidence X-ray diffraction measurements. After exposure to 75% R.H. in air for 8 days, the reaction layer increases in density as compared to the sample reacted in humid N 2 for 5–15 min. Further, this may represent an initial step toward the crystallization of the reaction layer. Overall, high R.H. favors the formation of a hydrated, disordered layer on MgO. Based on our results, DAC in a location with a higher R.H. will be favorable, but growth may slow significantly from initial rates even on short timescales, presumably due to surface passivation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Wafer-Scale Synthesis of 2D Materials by an Amorphous Phase-Mediated Crystallization Approach

The interest in the wafer-scale growth of two-dimensional (2D) materials, including transition metal dichalcogenides (TMDCs), has been rising for transitioning from lab-scale devices to commercial-scale systems. Among various synthesis techniques, physical vapor deposition, such as pulsed laser deposition (PLD), has shown promise for the wafer-scale growth of 2D materials. However, due to the high volatility of chalcogen atoms (e.g., S and Se), films deposited by PLD usually suffer from a lack of stoichiometry and chalcogen deficiency. To mitigate this issue, excess chalcogen is necessary during the deposition, which results in problems like uniformity or not being repeatable. This study demonstrates a condensed-phase or amorphous phase-mediated crystallization (APMC) approach for the wafer-scale synthesis of 2D materials. This method uses a room-temperature PLD process for the deposition and formation of amorphous precursors with controlled thicknesses, followed by a post-deposition crystallization process to convert the amorphous materials to crystalline structures. This approach maintains the stoichiometry of the deposited materials throughout the deposition and crystallization process and enables the large-scale synthesis of crystalline 2D materials (e.g., MoS 2 and WSe 2 ) on Si/SiO 2 substrates, which is critical for future wafer-scale electronics. We show that the thickness of the layers can be digitally controlled by the number of laser pulses during the PLD phase. Optical spectroscopy is used to monitor the crystallization dynamics of amorphous layers as a function of annealing temperature. The crystalline quality, domain sizes, and the number of layers were explored using nanoscale and atomistic characterization (e.g., AFM, STEM, and EDS) along with electrical characterization to explore process–structure–performance relationships. Finally, this growth technique is a promising method that could potentially be adopted in conventional semiconductor industries for wafer-scale manufacturing of next-generation electronic and optoelectronic devices.

2D electronics↗
DOE OSTI2023

Understanding Interfacial Electrochemical Reactions through in situ ec-STEM and IL-Cryo-STEM

A major criterion in the design of next generation materials for electrical energy storage applications is a comprehensive understanding of interfacial electrochemical reactions as well as correlating the structure and chemistry across site-specific electrode/electrolyte interfaces with electron, charge, and mass transport processes as they govern performance characteristics. Scanning transmission electron microscopy (STEM) based techniques have emerged as an indispensable materials characterization tool that provides high spatial resolution imaging and chemical analysis and has been effectively utilized to obtain an atomic to nanoscale view of the interfacial structure before and after electrochemical cycling. More recently, there have been several advances that now allows us to obtain more detailed mechanistic insight into evolving reactions through in situ ec-STEM and electrical biasing platforms such as in the understanding of the mechanisms of solid electrolyte interphase formation, lithium dendrite nucleation and growth mechanisms and ionic transport mechanisms within intercalation, conversion, and alloying electrode materials. Several major advantages of the in situ ec-STEM approach is the quantitative electrochemical measurement of charge passed during cycling with simultaneous analysis of the electrochemical processes with STEM imaging and diffraction. Here, while spectroscopic analysis of the electrochemical reactions products has been performed, there is the issue of beam sensitivity and therefore, Cryo-STEM imaging combined with electron energy loss spectroscopy (EELS) techniques have been employed to analyze the chemistry of the SEI and Li dendrites. In this talk, we discuss the potential for combining identical location (IL) STEM techniques with Cryo-EM. The advantage of using this approach is that the sample is placed on a conventional TEM grid and the exact same location of the specimen can be analyzed before and after quantitative electrochemical measurements. Moreover, since the sample is on the TEM grid, the grid itself can be prepared for further Cryo-TEM experiments by plunge freezing in liquid nitrogen then transferred to the Cryo-TEM under liquid nitrogen. Results obtain from these experiments can be used to enhance our scientific understanding of interfacial chemistry at electrode/electrolyte interfaces and may be useful in the design of new materials.

36 MATERIALS SCIENCE↗
DOE OSTI2023

The Atomic Drill Bit: Precision Controlled Atomic Fabrication of 2D Materials

The ability to deterministically fabricate nanoscale architectures with atomic precision is the central goal of nanotechnology, whereby highly localized changes in the atomic structure can be exploited to control device properties at their fundamental physical limit. Here, an automated, feedback-controlled atomic fabrication method is reported and the formation of 1D–2D heterostructures in MoS 2 is demonstrated through selective transformations along specific crystallographic orientations. The atomic-scale probe of an aberration-corrected scanning transmission electron microscope (STEM) is used, and the shape and symmetry of the scan pathway relative to the sample orientation are controlled. The focused and shaped electron beam is used to reliably create Mo 6 S 6 nanowire (MoS-NW) terminated metallic-semiconductor 1D–2D edge structures within a pristine MoS 2 monolayer with atomic precision. From these results, it is found that a triangular beam path aligned along the zig-zag sulfur terminated (ZZS) direction forms stable MoS-NW edge structures with the highest degree of fidelity without resulting in disordering of the surrounding MoS 2 monolayer. Density functional theory (DFT) calculations and ab initio molecular dynamic simulations (AIMD) are used to calculate the energetic barriers for the most stable atomic edge structures and atomic transformation pathways. These discoveries provide an automated method to improve understanding of atomic-scale transformations while opening a pathway toward more precise atomic-scale engineering of materials.

2D materials↗
DOE OSTI2022

Probing Electron Beam Induced Transformations on a Single-Defect Level via Automated Scanning Transmission Electron Microscopy

A robust approach for real-time analysis of the scanning transmission electron microscopy (STEM) data streams, based on ensemble learning and iterative training (ELIT) of deep convolutional neural networks, is implemented on an operational microscope, enabling the exploration of the dynamics of specific atomic configurations under electron beam irradiation via an automated experiment in STEM. Combined with beam control, this approach allows studying beam effects on selected atomic groups and chemical bonds in a fully automated mode. Here, in this study, we demonstrate atomically precise engineering of single vacancy lines in transition metal dichalcogenides and the creation and identification of topological defects in graphene. The ELIT-based approach facilitates direct on-the-fly analysis of the STEM data and engenders real-time feedback schemes for probing electron beam chemistry, atomic manipulation, and atom by atom assembly.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Building Atomic and Plasmonic Devices via Electron Beams: from Desired Structures to Desired Properties

The evolution of the aberration correction in Scanning Transmission Electron Microscopy (STEM) has enabled multiple advances including high-resolution structural imaging, pm-level position detection of atomic columns, and ~3-5 mV resolution electron energy loss spectroscopy of the chemical and physical functionalities. These developments have further enabled the precise manipulation of the atomic structure of materials, including removal and formation of atomic planes in 3D materials, controlled atomic motion, and even direct atomic assembly of homo- and heteroatomic artificial molecules. Here, we will discuss several recent advances in STEM-EELS automated experiments as applied to quantum and nanoplasmonic systems.

42 ENGINEERING↗
DOE OSTI2022

Laser-Assisted Synthesis of Monolayer 2D MoSe 2 Crystals with Tunable Vacancy Concentrations: Implications for Gas and Biosensing

We report tuning the structural and electronic properties of atomically thin two-dimensional (2D) materials via defect and vacancy engineering is the key to enabling their potential use in various applications, including electronics, energy, and sensing devices. Vacancies are, for instance, becoming highly promising for the enhanced interaction of gases and biomolecules with 2D materials in energy and sensing applications. However, the deterministic generation of desirable vacancies with tunable concentrations remains a challenge in 2D materials due to the limitations in the current growth methods, such as the complex reaction chemistries and gas flow dynamics. Therefore, engineering defects and vacancies in 2D materials have been mainly limited to destructive top-down processes such as heating, ion bombardments, and laser postprocessing. Here, we introduce a single-step bottom-up synthesis approach for the growth of monolayer MoSe 2 crystals with tunable vacancy concentrations. This method utilizes the spatiotemporal properties and adjustable power densities of the lasers to control the vaporization dynamics of the stoichiometric MoSe 2 powders. Such a mechanism in the vaporization allows us to grow tunable stoichiometry monolayer MoSe 2–x crystals on the substrates. The localized and time-controlled (250 ms to 2 s) vaporization of the MoSe 2 powder by a CO 2 laser enables the formation of monolayer crystals with controlled vacancy concentrations ranging from ~1 to 20%. The effects of laser power, laser irradiation time, and background pressure on the tuning range and subsequent properties of the crystals are investigated and quantified using Raman and photoluminescence spectroscopy, scanning transmission electron microscopy (STEM), and time-correlated single-photon counting (TCSPC). This bottom-up synthesis is a promising approach that allows the deterministic vacancy tuning for future electronics and, in particular, gas and biosensing applications without the need for further postprocessing and potential structural disruption of the crystals.

2D materials↗
DOE OSTI2020

Spontaneous and reversible hollowing of alloy anode nanocrystals for stable battery cycling

High-capacity alloy anode materials for Li-ion batteries have long been held back by limited cyclability caused by the large volume changes during lithium insertion and removal. Hollow and yolk-shell nanostructures have been used to increase the cycling stability by providing an inner void space to accommodate volume changes and a mechanically and dimensionally stable outer surface. These materials, however, require complex synthesis procedures. Here, using in situ transmission electron microscopy, we show that sufficiently small antimony nanocrystals spontaneously form uniform voids on the removal of lithium, which are then reversibly filled and vacated during cycling. This behaviour is found to arise from a resilient native oxide layer that allows for an initial expansion during lithiation but mechanically prevents shrinkage as antimony forms voids during delithiation. In this work, we developed a chemomechanical model that explains these observations, and we demonstrate that this behaviour is size dependent. Thus, antimony naturally evolves to form optimal nanostructures for alloy anodes, as we show through electrochemical experiments in a half-cell configuration in which 15-nm antimony nanocrystals have a consistently higher Coulombic efficiency than larger nanoparticles.

25 ENERGY STORAGE↗