Search NASA⌕ Search

Engineering topics

Boedo, J. A.

Publications and source records attributed to Boedo, J. A..

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Modeling turbulent impurity transport in the SOL of DIII-D with a reduced model

A novel impurity transport model that approximates SOL turbulence as a fluctuating poloidal electric field is shown to be an acceptable replacement for the traditional approach of assigning an arbitrary radial diffusion coefficient to the impurity ions. The model is implemented in the DIVIMP impurity transport code and applied to an L-Mode tungsten divertor experiment on DIII-D. The poloidal electric field is represented as fluctuating between ±1000 V m –1 based on previous measurements. The resulting intermittent v r = E θ × B T transport causes ions to transport both into the core as well as into the far-SOL. Simultaneous agreement with estimates of the W density just inside the separatrix as well as in the far-SOL is obtained (n W ~ 10 14 m –3 and n W ~ 10 12 m –3 , respectively). Prompt re-deposition of the W ions was necessary to obtain agreement (f redep ~ 99%). Here, we conclude that simulating impurity transport using a physics-based approximation for turbulence in the SOL, versus arbitrarily assigning diffusion coefficients, may enable better reactor scale predictions of core impurity contamination.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Measurements and modeling of type-I and type-II ELMs heat flux to the DIII-D divertor

Type-I and type-II edge-localized-modes (ELMs) heat flux profiles measured at the DIII-D divertor feature a peak in the vicinity of the strike-point and a plateau in the scrape-off-layer (SOL), which extends to the first wall. The plateau is present in attached and detached divertors and it is found to originate with plasma bursts upstream in the SOL. The integrated ELM heat flux is distributed at ~65% in the peak and ~35% in this plateau. The parallel loss model, currently used at ITER to predict power loads to the walls, is benchmarked using these results in the primary and secondary divertors with unprecedented constraints using experimental input data for ELM size, radial velocity, energy, electron temperature and density, heat flux footprints and number of filaments. The model can reproduce the experimental near-SOL peak within ~20%, but cannot match the SOL plateau. Employing a two-component approach for the ELM radial velocity, as guided by intermittent data, the full radial heat flux profile can be well matched. The ELM-averaged radial velocity at the separatrix, which explains profile widening, increases from ~0.2 km s –1 in attached to ~0.8 km s –1 in detached scenarios, as the ELM filaments' path becomes electrically disconnected from the sheath at the target. The results presented here indicate filaments fragmentation as a possible mechanism for ELM transport to the far-SOL and provide evidence on the beneficial role of detachment to mitigate ELM flux in the divertor far-SOL. However, these findings imply that wall regions far from the strike points in future machines should be designed to withstand significant heat flux, even for small-ELM regimes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

The fast camera (Fastcam) imaging diagnostic systems on the DIII-D tokamak

Two camera systems are installed on the DIII-D tokamak at the toroidal positions of 90° (90° system) and 225° (225° system), respectively. The cameras have two types of relay optics, namely, a coherent optical fiber bundle and a periscope system. The periscope system provides absolute intensity calibration stability while sacrificing resolution (10 lp/mm), while the fiber system provides high resolution (16 lp/mm) while sacrificing calibration stability. The periscope is available only for the 90° system. The optics of the 225° system were designed for view stability, repeatability, and easy maintenance. The cameras are located inside optimized neutron, x ray and magnetic shielding in order to reduce electronics damage, reboots, and magnetic and neutron interference, increasing the overall system reliability. An automated filter wheel, providing remote filter change, allows for remote wavelength selection. A software suite automates camera acquisition and data storage, allowing for remote operation and reduced operator involvement. System metadata is used to streamline the data analysis workflow, particularly for intensity calibration. Here, the spatial calibration uses multiple observable wall features, resulting in a reconstruction accuracy ≤2 cm.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Dependence of scrape-off layer profiles and turbulence on gas fuelling in high density H-mode regimes in TCV

A set of high density, highly shaped H-mode discharges has been performed in the TCV tokamak with the aim of assessing the effects of increasing divertor neutral recycling on the properties of upstream inter-ELM scrape-off layer (SOL) profiles and transport. An increase of divertor neutral pressure has been correlated with the evolution of separatrix properties and turbulence level. The latter has been quantified by means of the α t parameter introduced in (Eich 2020 Nucl. Fusion 60 056016), describing the contribution of resistive-interchange turbulence in the SOL relative to drift wave transport. The analysis reveals a general broadening of the upstream SOL profiles as α t increases, with the SOL power width measured by the vertical IR thermography system increasing significantly. In a similar way, the upstream density profile widens in the near SOL, whereas in the far SOL a density shoulder is observed to progressively form and increase in amplitude. This behaviour is associated with an enhancement of far SOL turbulent transport in the form of blob-filaments travelling radially faster across the far SOL and becoming bigger at higher α t . Finally, the detected filaments, evaluated from the fast reciprocating probe at the outer midplane, are determined to mostly belong to the resistive ballooning and resistive X-point regimes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Validation of edge turbulence codes against the TCV-X21 diverted L-mode reference case

Self-consistent full-size turbulent-transport simulations of the divertor and scrape-off-layer (SOL) of existing tokamaks have recently become feasible. This enables the direct comparison of turbulence simulations against experimental measurements. In this work, we perform a series of diverted ohmic L-mode discharges on the tokamak à configuration variable (TCV) tokamak, building a first-of-a-kind dataset for the validation of edge turbulence models. This dataset, referred to as TCV-X21, contains measurements from five diagnostic systems from the outboard midplane (OMP) to the divertor targets—giving a total of 45 one- and two-dimensional comparison observables in two toroidal magnetic field directions. The experimental dataset is used to validate three flux-driven 3D fluid-turbulence models—GBS, GRILLIX and TOKAM3X. With each model, we perform simulations of the TCV-X21 scenario, individually tuning the particle and power source rates to achieve a reasonable match of the upstream separatrix value of density and electron temperature. We find that the simulations match the experimental profiles for most observables at the OMP—both in terms of profile shape and absolute magnitude—while a comparatively poorer agreement is found towards the divertor targets. The match between simulation and experiment is seen to be sensitive to the value of the resistivity, the heat conductivities, the power injection rate and the choice of sheath boundary conditions. Additionally, despite targeting a sheath-limited regime, the discrepancy between simulations and experiment also suggests that the neutral dynamics should be included. The results of this validation show that turbulence models are able to perform simulations of existing devices and achieve reasonable agreement with experimental measurements. Where disagreement is found, the validation helps to identify how the models can be improved. By publicly releasing the experimental dataset and validation analysis, this work should help to guide and accelerate the development of predictive turbulence simulations of the edge and SOL.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Evidence on the effects of main-chamber neutrals on density shoulder broadening

Evidence that density shoulder broadening is dependent on high main-chamber neutral density is presented. Shoulder broadening does not occur when the sources for main-chamber neutrals are minimized using divertor baffles and wide gaps to the first wall (~3× the density decay length). Removing the baffles or reducing the gap to the inner wall both act to increase the density shoulder amplitude in otherwise identical TCV discharges. Radial turbulent transport is correlated with shoulder amplitude.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

Quantifying heat and particle flux to primary and secondary divertors for various types of edge-localized-modes

Between 15% and 30% of edge-localized-mode (ELM) heat flux can be deposited to regions outside the main divertor including the far scrape-off-layer (SOL), private flux region (PFR), and secondary divertor inner target. Analysis shown here demonstrates that type-I and small ELM plasmas are transported to the PFR and to the secondary inner divertor, which is magnetically isolated from the outer divertor, leading to well-defined heat flux profiles and with peak values that can surpass those at the secondary outer target. Such features are consistently observed for pedestal collisionalities from $ν$$^{*}_{e}$ ~1.5 to $ν$$^{*}_{e}$ ~3.9. Heat flux profiles of the examined ELM types feature rippled structures due to bursts in the outer far-SOL region but not on the secondary inner target, causing long decay lengths in the time-averaged ELM profiles. The contribution of each ELM type to the total time-averaged power deposited to the secondary divertor has been evaluated, showing that grassy ELMs contribute ~8%, small ELMs ~67%, and type-I ELMs ~85%. These findings imply that small ELMs may yet pose a concern for future machines if some regions of the main wall are not designed to withstand significant heat and particle fluxes. Due to the low intra-ELM heat flux contribution, however, the grassy ELM regime is an attractive option for an ELMing scenario in future machines.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Relevance of E × B drifts for particle and heat transport in divertors

Radial electric fields up to ~4 kV m –1 are observed in the boundary between the private flux region (PFR) and the scrape-off layer (SOL) driving E × B drifts between the inner and outer targets at speeds up to 2.8 km s –1 in the Tokamak à configuration variable divertor. The resulting E × B fluxes, located in a narrow region ($\Delta {\rho _\Psi } < 0.012$ in normalized radius or $\Delta $ R – R sep <4 mm mapped to the outer midplane) are equivalent to around 20% of the total heat and particle flux to the divertor targets (inner + outer). At the peak E r , the E × B poloidal transport is equivalent to parallel flows with M ∥ ~ 3. In the snowflake divertor with a second X-point in the outer SOL, the drifts in the PFR-SOL boundary were equivalent to around 30% of the total heat and particle flux to the divertor targets and cover a region ~50% wider than in the single null ($\Delta {\rho _\Psi }$ ~ 0.018, $\Delta $R – R sep ~ 6 mm). Furthermore, the location of the PFR-SOL boundary drift shifts radially in the E ∥ × B direction when reversing the toroidal field direction. Peaks in density and electron pressure have been identified near the primary X-point along with large gradients in density, temperature, and potential, the latter resulting in a local electric field ~2.7 kV m –1 which drives a drift (1.9 km s –1 ) upwards towards the closed flux surfaces. Floating potential (V f ) magnitudes up to 75 V (~2 kT e ) were measured, indicating that V f and parallel currents should not be neglected when estimating plasma potential.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Suppression of first-wall interaction in negative triangularity plasmas on TCV

Magnetically confined fusion plasmas with negative triangularity (d) exhibit greater L-mode confinement than with positive d. Recent experiments in the TCV and DIII-D tokamaks have correlated the confinement improvement to a reduction of fluctuations within the plasma core. We report on fluctuation measurements in the scrape-off layer (SOL) for −0.61 < d < +0.64 in limited and diverted ohmic L-mode plasmas; these reveal a strong reduction in SOL fluctuation amplitudes at d < −0.25, and, surprisingly, an almost full suppression of plasma interaction with the main-chamber first-wall, which could have important implications for the prospects of using negative d plasmas as a reactor solution. An exploration of several physical mechanisms suggests that a reduced connection length—intrinsic to negative d plasmas—plays a critical role in the origin of this phenomenon.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Theory-based scaling laws of near and far scrape-off layer widths in single-null L-mode discharges

Abstract Theory-based scaling laws of the near and far scrape-off layer (SOL) widths are analytically derived for L-mode diverted tokamak discharges by using a two-fluid model. The near SOL pressure and density decay lengths are obtained by leveraging a balance among the power source, perpendicular turbulent transport across the separatrix, and parallel losses at the vessel wall, while the far SOL pressure and density decay lengths are derived by using a model of intermittent transport mediated by filaments. The analytical estimates of the pressure decay length in the near SOL is then compared to the results of three-dimensional, flux-driven, global, two-fluid turbulence simulations of L-mode diverted tokamak plasmas, and validated against experimental measurements taken from an experimental multi-machine database of divertor heat flux profiles, showing in both cases a very good agreement. Analogously, the theoretical scaling law for the pressure decay length in the far SOL is compared to simulation results and to experimental measurements in TCV L-mode discharges, pointing out the need of a large multi-machine database for the far SOL decay lengths.

Physics↗
DOE OSTI2021

Overview of the TCV tokamak program: Scientific progress and facility upgrades

The TCV tokamak is augmenting its unique historical capabilities (strong shaping, strong electron heating) with ion heating, additional electron heating compatible with high densities, and variable divertor geometry, in a multifaceted upgrade program designed to broaden its operational range without sacrificing its fundamental flexibility. The TCV program is rooted in a three-pronged approach aimed at ITER support, explorations towards DEMO, and fundamental research. A 1 MW, tangential neutral beam injector (NBI) was recently installed and promptly extended the TCV parameter range, with record ion temperatures and toroidal rotation velocities and measurable neutral-beam current drive. ITER-relevant scenario development has received particular attention, with strategies aimed at maximizing performance through optimized discharge trajectories to avoid MHD instabilities, such as peeling-ballooning and neoclassical tearing modes. Experiments on exhaust physics have focused particularly on detachment, a necessary step to a DEMO reactor, in a comprehensive set of conventional and advanced divertor concepts. The specific theoretical prediction of an enhanced radiation region between the two X-points in the low-field-side snowflake-minus configuration was experimentally confirmed. Fundamental investigations of the power decay length in the scrape-off layer (SOL) are progressing rapidly, again in widely varying configurations and in both D and He plasmas; in particular, the double decay length in L-mode limited plasmas was found to be replaced by a single length at high SOL resistivity. Experiments on disruption mitigation by massive gas injection and electron-cyclotron resonance heating (ECRH) have begun in earnest, in parallel with studies of runaway electron generation and control, in both stable and disruptive conditions; a quiescent runaway beam carrying the entire electrical current appears to develop in some cases. Developments in plasma control have benefited from progress in individual controller design and have evolved steadily towards controller integration, mostly within an environment supervised by a tokamak profile control simulator. TCV has demonstrated effective wall conditioning with ECRH in He in support of the preparations for JT-60SA operation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Parallel convection and E × B drifts in the TCV snowflake divertor and their effects on target heat-fluxes

Parallel convection and E × B drifts act together to redistribute heat between the strike-points in the low field side snowflake minus (LFS SF–). The cumulative heat convection from both mechanisms is enhanced near the secondary X-point and is shown to dominate over heat conduction, partly explaining why the LFS SF– distributes power more evenly than the single null (SN) or other snowflake (SF) configurations. Pressure profiles at the entrance of the divertor are strongly affected by the position of the secondary X-point and magnetic field direction indicating the importance of E × B drifts. Pressure drops of up to 50% appear between the outer-midplane (OMP) and the divertor entrance enhancing the role of parallel heat convection. The electron temperature and density profiles and the radial turbulent fluxes measured at the OMP are largely unaffected by the changes in divertor geometry, even on flux surfaces where the connection length is infinite.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Observations of wall conditioning by means of boron powder injection in DIII-D H-mode plasmas

In this paper, we report observations from the DIII-D tokamak indicating that boron (B) powder injection in tokamak plasmas improves wall conditions similarly to glow discharge boronization (GDB). Isotopically enriched B powder (B 11 > 95%) was introduced gravitationally in a sequence of H-mode plasma discharges at rates up to ~160 mg s -1 for durations up to 3 s. Boron injection to cumulative amounts ≤0.1 g appeared to improve wall conditions similarly to boronization, with indications of reduced wall fueling, reduced recycling at the outer strike point and reduced impurity content at breakdown. Post-mortem analysis of graphite samples exposed to far scrape-off layer plasma fluxes during boron injection confirm the formation of a B-C layer, with average surface composition B:C ~ 1. The results suggest that injecting boron-rich powders in tokamak plasmas can effectively replenish boron films on carbon plasma facing components to improve wall conditions and extend the duration of the beneficial effects of GDB.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Neutral leakage, power dissipation and pedestal fueling in open vs closed divertors

The effect of divertor closure on neutral leakage, power dissipation and pedestal fueling is explored using the SOLPS code for different densities including attached and detached divertor conditions for DIII-D open and closed divertors. Here, a metric for divertor closure in terms of the percentage of neutrals escaping the divertor is presented. At the detachment onset the population of neutrals escaping the divertor is 12% for the closed divertor and 35% for the open divertor. This results in a lower contribution of the convective term to the total heat flux and increased power losses in the closed divertor. The comparison between the two geometries reveals that for the same upstream density, the upstream temperature is 23% higher in the closed divertor. The physical mechanisms for detachment at lower upstream density in the closed divertor are also identified with the reduction of the convective term directly resulting in 40% decrease and the increased power losses contributing with a factor of 2. The baffling also lowers the neutral flux refueling the pedestal resulting in further reduction of the core density for achieving detachment. The results introduced here show that the divertor recycling is the primary fueling mechanism in DIII-D. It is shown that fueling occurring in the region between the X-point and the outer midplane is at least four times lower in the closed divertor due the baffling structure which enhances target neutral trapping and consequently reduced upstream leakage. Due to the openness of the inner leg to the common flux and HFS regions both open and closed divertor experience almost identical fueling at the HFS highlighting the need to also consider the inboard divertor for shape optimization.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Impact of divertor material on neutral recycling and discharge fueling in DIII-D

We report that experiments with the lower divertor of DIII-D during the Metal Rings Campaign (MRC) show that the fraction F of atomic D in the total recycling flux is material-dependent and varies through the ELM cycle, which may affect divertor fueling. Between ELMs, F C ~ 10% and FW ~ 40%, consistent with expectations if all atomic recycling is due to reflections. During ELMs, F C increases to 50% and F W to 60%. In contrast, the total D recycling coefficient including atoms and molecules R stays close to unity near the strike point where the surface is saturated with D. During ELMs, R can deviate from unity, increasing during high energy ELM-ion deposition (net D release) and decreasing at the end of the ELM which leads to ability of the target to trap the ELM-deposited D. The increase of R > 1 in response to an increase in ion impact energy Ei has been studied with small divertor target samples using Divertor Materials Evaluation System (DiMES). An electrostatic bias was applied to DiMES to change E i by 90 eV. On all studied materials including C, Mo, uncoated and W-coated TZM (>99% Mo, Ti, and Zr alloy), W, and W fuzz, an increase of E i transiently increased the D yield (and R) by ~10%. On C there was also an increase in the molecular D 2 yield, probably due to ion-induced D 2 desorption. Despite the measured increase in F on W compared to C, attached H-mode shots with OSP on W during MRC did not demonstrate a higher pedestal density. About 8% increase in the edge density could be seen only in attached L-mode scenarios. The difference can be explained by higher D trapping in the divertor and lower divertor fueling efficiency in H- versus L-mode.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Nitrogen-seeded divertor detachment in TCV L-mode plasmas

Most of the detachment experiments done to date on the tokamak à configuration variable (TCV), both in standard and alternative divertor geometries, focused on L-mode integrated core density ramps. In view of extending these studies to high-power, high-confinement regimes, where impurity seeding will be necessary for detachment, the properties of nitrogen seeded L-mode detachment in TCV are assessed here with the extensive set of edge and divertor diagnostics and similarities and differences with integrated core density ($\langle n_e \rangle$) ramp detachment experiments are elucidated. It is found that in high current, reversed field plasmas, detachment at the outer target is achieved with N 2 -seeding and density ramps, with target heat flux reductions of up to 90%, while the inner target only detaches with seeding. The Scrape-Off Layer radiation fraction reaches values of 60%–80% and in all situations, a stable radiator can form around the X-point. In this work, the most striking difference between seeding and density ramp is the behavior of the upstream quantities. During the $\langle n_e \rangle$-ramp, a broadening of the upstream density profile (density ‘shoulder’) occurs, concurrent with the outer target ion flux roll-over, while no such behavior occurs during nitrogen seeded detachment. Separatrix density, electron temperature and pressure also evolve strongly with increasing density, and are largely unaffected by the injection of nitrogen. Comparison of upstream and target pressures reveals that, in all cases, the outer target ion flux reduction coincides with the development of a parallel gradient of the total pressure. Common to all cases is also a reduction of energy confinement time with detachment, although this effect is weak for seeding at relatively high density. Studying the impact of the ∇B-drift direction in both nitrogen seeding and core density ramps reveals that drifts mainly affect the behavior at the inner strike point, highlighting the need to include them in edge transport simulations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗