Search NASA⌕ Search

Engineering topics

Bohn, Kevin Ray

Publications and source records attributed to Bohn, Kevin Ray.

U-rich U-Mo Solidus, Liquidus, Enthalpy, and Thermal Diffusivity

Several material properties have been studied as a function of composition as part of the USHPRR effort to use U-10Mo for LEU monolithic fuel foils, with special attention to areas where simulation outcomes can be improved. The liquidus and solidus phase boundaries are important for engineering design of processing parameters and for predicting the degree of microsegregation within initial castings. The numerous phase diagram constructions available in the literature differ significantly in their solid/liquid boundary definitions, therefore, an experimental strategy was employed in order to resolve some of the discord. That strategy focuses not on proving any singular point, but instead to provide data with highly characterized uncertainty. The data presented here is the most consistent with the U-rich liquidus and solidus boundaries provided by H. Okamoto (2012), Berche et al. (2011), and Mardon et al. (1959). The recently suggested change in the peritectic reaction temperature (to 1302 K) suggested by Berchè and adopted by Okamoto is also supported, but with lower confidence. The enthalpy of fusion is a basic characteristic of the solidification reaction property for which is required for both research-oriented predictions of behavior and development of applied design strategies for casting engineering. It has been determined that an admixture model for the heat of fusion between U BCC and Mo BCC is a reasonable assumption within the composition region of interest, though limitations of the measurement accuracy impacts the ability to support any trends more detailed than this baseline behavior. A limited number of thermal diffusivity measurements were also performed into the gamma region to provide additional information for solidification modeling and simulations as well as a check on the component properties of thermal conductivity, density, and heat capacity.

36 MATERIALS SCIENCE↗

EDEN Tube Interface Characterization Report

In 2022 Eden Radioisotopes and Los Alamos National Laboratory entered into a Creative Research and Development Agreement (CRADA) leveraging the metallography capabilities of the Characterization and Special Projects Team of Sigma-2 at LANL. EDEN identified a need to characterize the condition of metallic interfaces within their product created at different pressure conditions to see which processing parameters achieved interfaces within specifications for intended use. A total of 4 samples were sent to the Characterization Projects team and 3 were later sent to another facility (MST-7) where Micro CT was performed.

36 MATERIALS SCIENCE↗

FY18 Report: HFIR Fuel Casting Support and Microstructural Feature Examination

An effort to commence conversion of the High Flux Isotope Reactor (HFIR) to a low enriched uranium (LEU) based fuel has been proposed. While recent experience from LEU-10wt%Mo (U-10Mo) monolithic metal fuel production may be leveraged considerably, the significant differences between research fuels requires some degree of strategy reassessment. In that spirit, initial casting trials have been performed at LANL over the last two years in order develop a high quality starting metal ingot.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Metallurgical Failure Analysis of A2 Tool Steel Die Set from High Explosive Pellet Pressing Event

On 2 April 2018, a high explosive violent reaction (HEVR) occurred during routine pressing of a 1-in -diameter cylindrical pellet of PBX 9501 high explosive. Fragments of the die set (die body and stemples) involved in the event were sent to Sigma Division for metallurgical analysis. A handheld x-ray fluorescence alloy tester confirmed the die set material to be A2 tool steel. Light optical microscopy revealed what appear to be pre-existing flaws on the inner diameter of the die body. Scanning Electron Microscopy could neither confirm nor exclude the presence of fatigue cracking in the vicinity of these potential flaws. Energy Dispersive Spectroscopy indicated the presence of a carbon-bearing residue on fracture surfaces; nitrogen-bearing residue was also found. Optical microscopy revealed that the microstructure of the stemple and inner diameter of the die body contained large stringers and non-uniform grain size; this was distinct from the relatively clean and uniform microstructure seen at the outer diameter of the die body, and also other A2 tool steel stock (pedigree unknown and with no known connection to any HE pressing hardware) that was examined for additional comparison. Rockwell hardness testing indicated the material was heat treated properly. Metallographic analysis alone could not positively identify the root cause of the event, but, coupled with accounts provided by the operator and the successful history with the particular lot of HE involved in the event, points to ward mechanical failure of the die set due to pre -existing flaw as the most likely precipitating event. Suggestions for additional analyses and future qualification techniques are discussed.

36 MATERIALS SCIENCE↗