Strain-rate dependence of the mechanical response of PBX 9502 at rates beyond 1000 /s
Explore the source record for details and available documents.
Engineering topics
Publications and source records attributed to Bolme, Cynthia Anne.
Explore the source record for details and available documents.
Conventional Split Hopkinson Pressure Bars (SHPB) or “Kolsky” bars are often used for determining the high-rate compressive yield and failure strength of materials. However, for experiments generating very high strain-rates (>10 3 /s) miniaturization of the setup is often required for minimizing the effects of elastic wave dispersion in order to enable the inference of decreasingly short loading events from the data. Miniature aluminum and steel bars are often sufficient for meeting these requirements. However, for high enough strain-rates, miniaturization of steel or aluminum Kolsky bars may require prohibitively small diameter bars and test specimens that could become inappropriate for inferring representative properties of materials with large grain size relative to the test specimen size. The use of a beryllium Kolsky bar setup is expected to enable high rates to be accessible with larger diameter bars/specimen combinations due to the inherent physical properties of beryllium, which are expected to minimize the effects of elastic wave dispersion. For this reason, a series of beryllium Kolsky bars have been developed, and, in this paper, the dispersion characteristics of these bars are measured and compare the data with those of similarly sized 7075-T6 aluminum and C350 maraging steel. The results, which agree well with the theory, show no appreciable frequency dependence of the elastic wavespeed in the data from the beryllium bars, demonstrating its advantage over aluminum and steel in application to Kolsky bars.
Mesoscale imperfections, such as pores and voids, can strongly modify the properties and the mechanical response of materials under extreme conditions. Tracking the material response and microstructure evolution during void collapse is crucial for understanding its performance. In particular, imperfections in the ablator materials, such as voids, can limit the efficiency of the fusion reaction and ultimately hinder ignition. To characterize how voids influence the response of materials during dynamic loading and seed hydrodynamic instabilities, we, in this paper, have developed a tailored fabrication procedure for designer targets with voids at specific locations. Our procedure uses SU-8 as a proxy for the ablator materials and hollow silica microspheres as a proxy for voids and pores. By using photolithography to design the targets’ geometry, we demonstrate precise and highly reproducible placement of a single void within the sample, which is key for a detailed understanding of its behavior under shock compression. This fabrication technique will benefit high-repetition rate experiments at x-ray and laser facilities. Insight from shock compression experiments will provide benchmarks for the next generation of microphysics modeling.
Here, this paper describes the calibration of the Arrhenius Wescott–Stewart–Davis (AWSD) reactive flow model for the recently developed high explosive PBX 9701, which consists of 97% 3,3'-diamino-4,4'-azoxyfurazan (DAAF) and 3% FK-800 binder by weight. DAAF-based explosive formulations have several desirable qualities as they are relatively insensitive to non-shock insults but have higher performance than triaminotrinitrobenzene based formulations. Equations of state for the explosive reactants and products are calibrated using a combination of existing and new experimental data and theoretical calculations. The AWSD rate law calibration utilizes both one-dimensional shock-to-detonation and multidimensional rate stick experiments to capture the shock initiation and propagating detonation regimes. Validation of the calibrated model is demonstrated through comparison with recent gas-gun experiments.
Explore the source record for details and available documents.
The dynamic thermo-mechanical behavior of pure aluminum has attracted renewed interest lately due to experimental observations of an anomalous increase in Hugoniot Elastic Limit (HEL) at incipient plasticity and elevated temperatures in polycrystalline pure metals. In context of current dislocation-mediated plasticity models for metals, this increase in dynamic strength is indicative of a transition in the rate controlling mechanism for dislocation glide from being thermally assisted to phonon-drag restricted due to increase in phonon viscosity at elevated temperatures. Though these studies have helped to shed light on these important mechanisms operative in FCC metals at incipient plasticity, the extent to which they contribute to flow stress, particularly at larger strains, remains unclear. Here, we address these questions through a combined experimental and modeling effort focused on investigating the evolution of dynamic flow stress in polycrystalline aluminum using experimental data gathered from a series of combined pressure-and-shear plate impact (PSPI) experiments designed to reveal the flow stress of pure aluminum at strain rates ~ 10 5 /s, plastic strains of up to 40% and temperatures ranging from room to 866 K. In all cases, the flow stress of aluminum, as inferred from the measured transverse particle velocity histories at the free surface of an elastic tungsten carbide target plate, reveals saturation with increasing plastic strains at stress levels that decrease with increasing test temperatures. Numerical simulations are performed to correlate the experimentally observed temperature and strain rate dependence of flow stress at small and large plastic strains using the Austin-McDowell dislocation-mediated plasticity model parametrized to normal plate impact experiments conducted in an earlier study by Zaretsky and Kanel (2012). Extensions to the model are made to better represent dynamic behavior of pure aluminum at larger plastic strains as observed in elevated temperature split Hopkinson Pressure bar (SPHB) experiments of Samanta (1971) and Lindholm and Yeakly (1965), and the combined pressure-and-shear plate-impact experiments conducted in the present study. The main theoretical extension to the Austin-McDowell model made in this paper is the introduction of a new rate- and temperature- dependent dynamic recovery function, which can potentially allow for an effective reduction in the rate of accumulation of dislocations at large plastic strains. The numerical predictions of the revised and re-calibrated plasticity model are brought into agreement with the experimental observations, correlating sufficiently well with dynamic yield stress at incipient plasticity and the flow stress levels at larger plastic strains, plastic strain rates in the range 10 3 – 10 6 /s, and elevated temperatures up to near melt. The model, in concert with the experimental measurements, suggests that at incipient plasticity the rate governing mechanism for plastic flow is phonon-drag restricted dislocation glide, whereas, at higher magnitudes of plastic strain, it transitions to stress-assisted thermally activated glide. The transition between these two rate governing mechanisms is controlled by the evolution of dislocations throughout the deformation process.
A novel set of experiments and reactive flow modeling of pentaerythritol tetranitrate (PETN) is presented. In this work, the specific phenomenon of shock to detonation transition is examined, where an initial, relatively weak shock is propagated into pressed PETN powder at 1.65 g/cm 3 and the subsequent buildup to detonation is observed experimentally. These experiments, in conjunction with reactant and products’ equations of state, are utilized for building reactive flow models.
The application of high pressure to materials has enabled discoveries in scientific fields such as planetary science, materials science, and materials synthesis. Recent advances in X-ray user light sources and other facilities, co-location and integration of user facilities with high-pressure drivers, availability of high-performance computing (HPC) platforms, and the development of new data science techniques have created opportunities for, and challenges in, advancing data analytics for rapid and dynamic compression experiments. To address these challenges, harness the emerging technology now available, and expedite scientific discovery, Los Alamos National Laboratory (LANL) hosted a virtual workshop entitled “Data Science and Computation for Rapid and Dynamic Compression Workflows at Experimental Facilities” from September 8 to 11, 2020. The workshop included 95 registered scientists and analytics experts from 15 universities, 9 United States (US) national laboratories, 5 US and European X-ray light sources, neutron sources such as the Los Alamos Neutron Science Center (LANSCE), other big science facilities such as the National Ignition Facility (NIF), and an industry representative. The workshop included 31 invited talks and 4 lightning talks by students and postdocs.
Novel PBX 9501 dynamic mock candidates were produced via the wet slurry process. The material selection criteria and development processes are detailed.
A method for purification of bench-to-pilot-scale quantities of conventional high explosives (CHE) was required. A commercial off the shelf Soxhlet extraction apparatus was redesigned and procured for high-quality, high throughput batches of materials.
In this study, thin films of pentaerythritol tetranitrate (PETN) were shock compressed using the laser driven shock apparatus at Los Alamos National Laboratory (LANL). Two spectroscopic probes were available to this apparatus: visible white light transient absorption spectroscopy (VIS) from 400 to 700 nm and mid-infrared transient absorption spectroscopy (MIR) from 1150 to 3800 cm –1 . Important PETN vibrational modes are the symmetric and antisymmetric NO 2 stretches at 1280 and 1650 cm –1 , respectively, as well as CH stretches at ~2900 cm –1 . Shock strength was varied from approximately 3 to 55 GPa to span from the chemically unreactive regime to the regime in which fast chemical reaction took place on the 250 ps time scale of the measurements. VIS and MIR results suggest irreversible chemistry was induced in PETN at pressures above 30 GPa. At lower shock pressures, the spectroscopy showed minimal changes attributable to pressure induced effects. Under the higher-pressure reactive conditions, the frequency region at the antisymmetric NO 2 stretch mode had a significantly increased absorption while the region around the symmetric NO 2 stretch did not. No observable increased absorption occurred in the higher frequency regions where CH-, NH-, and OH- bond absorptions would be observed. A broad absorption appeared on the shoulder at the red-edge of the CO 2 vibrational band around 2200 cm –1 . In addition to the experiments, reactive molecular dynamics were carried out under equivalent shock conditions to correlate the evolution of the infrared spectrum to molecular processes. The simulations show results consistent to experiments up to 30 GPa but suggest that NO and NO 2 related features provided the strongest contributions to the shocked infrared changes. Proposed mechanisms for shocked PETN chemistry are analyzed as consistent or inconsistent with the data presented here. Our experimental data suggests C≡O or N 2 O bond formation, nitrite formation, and absence of significant hydroxyl or amine concentrations in the initial chemistry steps in PETN shocked above 30 GPa.
Many important aspects of the dynamic thermo-mechanical response of materials occur at the mesoscale, i.e. a physical scale of interactions smaller than what can be adequately described by homogenous behaviors, yet larger than the scale of the atomic lattice. Concurrent advancements in computational power, continuum theory, and experimental diagnostics are enabling unprecedented understanding of such interactions. However, we cannot develop a sufficient level of confidence in such mesoscale capability until the constitutive description of the underlying constituents is reliably representative of their actual physical behavior. Therefore, there is a strong need to combine experimental, modeling, and data-science techniques to validate models of the thermomechanical response of individual single crystals. One experimental diagnostic with high potential impact to shock physics and materials science is in-situ x-ray diffraction. This paper is primarily focused on simulation of x-ray diffraction in shock physics, but with an aim toward quantifying parametric uncertainty of simulation models. Here, we develop and demonstrate a data-science and model-driven approach to constrain the parameterization of continuum models of crystal lattice deformation associated with the shock response of crystalline materials. The framework is built around the connection between continuum hydrodynamic simulations of lattice deformation and a new Bragg diffraction simulation code, BarberShop. The dynamic deformation of a crystal lattice is modeled using the DiscoFlux model within an arbitrary Lagrangian-Eulerian hydrodynamic code, FLAG. These detailed continuum simulations of lattice deformation can be computationally slow, thus a statistical model is used to emulate the evolution of lattice deformation fields in time and across the considered model parameter space. Emulated lattice deformation fields can then be generated rapidly for any combination of physics model parameters. In turn, these fields can be fed into BarberShop to realize a rapid prediction of Bragg diffraction patterns associated with particular values of physics model parameters. The framework enables parameterization of the single crystal model to obtain Bragg diffraction patterns that most closely resemble a corresponding measurement. Furthermore, the framework naturally provides sensitivities of the lattice deformation to the physics parameters. We highlight the utility of this framework through the application to a synthetic closed-loop inverse problem leading to the parameterization of a single crystal material model. As a model problem, we consider the dynamic response of the energetic molecular crystal, cyclotrimethylenetrinitramine (or RDX), under dynamic compression induced by simulated flyer plate impact experiments.
Explore the source record for details and available documents.
Here we interpret previous experimental measurements of impacts on single crystal PETN in the context of a simple continuum model. Hugoniot calculations using the simple model framework under various limiting assumptions envelope measured Hugoniot states reasonably well and suggest that non-negligible deviatoric elastic strains may exist in the shock compressed state for weak impacts. An accompanying simple kinematic model for lattice deformation was used to estimate the expected shifts in X-ray diffraction peaks for the (211) plane under impacts normal to (110) planes. The results suggest that negligible relaxation of the deviatoric lattice deformation occurs on the short (10–20 ns) time and wave propagation (40–80 m) scales of laser-driven shock experiments, and that the corresponding elastic strains may be large. Because of the potentially large deviatoric elastic strains, the specific finite deformation strain measure used within thermomechanical single crystal models is of significant consequence, which is explored numerically by the comparison of isothermal purely elastic responses under uniaxial and simple shear deformations.
Common Ti:sapphire chirped pulse amplified laser systems can be readily adapted to be both a generator of adjustable pressure shock waves and a source for multiple probes of the ensuing ultrafast shock dynamics. Here, we detail experimental considerations for optimizing the shock generation, interferometric characterization, and spectroscopic probing of shock dynamics with visible and mid-infrared transient absorption. While we have reported results using these techniques elsewhere, in this work we detail how the spectroscopies are integrated with the shock and interferometry experiment. The interferometric characterization uses information from beams at multiple polarizations and angles of incidence combined with thin film equations and shock dynamics to determine the shock velocity, particle velocity, and shocked refractive index. Visible transient absorption spectroscopy uses a white light supercontinuum in a reflection geometry, synchronized to the shock wave, to time resolve shock-induced changes in visible absorption such as changes to electronic structure or strongly absorbing products and intermediates due to reaction. Mid-infrared transient absorption spectroscopy uses two color filamentation supercontinuum generation combined with a simple thermal imaging microbolometer spectrometer to enable broadband single shot detection of changes in the vibrational spectra. These methods are reflected here in the study of shock dynamics at stresses from 5 to 30 GPa in organic materials and from a few GPa to >70 GPa in metals with spatial resolution of a few micrometers and temporal resolution of a few picoseconds. This experiment would be possible to replicate in any ultrafast laser laboratory containing a single bench top commercial chirped pulse amplification laser system.
We report that predictive modeling of materials requires accurately parameterized constitutive models. Parameterizing models that describe dynamic strength and plasticity require experimentally probing materials in a variety of strain rate regimes. Some experimental protocols (e.g., plate impact) probe the constitutive response of a material using indirect measures such as free surface velocimetry. Manual efforts to parameterize constitutive models using indirect experimental measures often lead to non-unique optimizations without quantification of parameter uncertainty. This study uses a Bayesian statistical approach to find model parameters and to quantify the uncertainty of the resulting parameters. The technique is demonstrated by parameterizing the Johnson-Cook strength model for aluminum alloy 5083 by coupling hydrocode simulations and velocimetry measurements of a series of plate impact experiments. Simulation inputs and outputs are used to calibrate an emulator that mimics the outputs of the computationally intensive simulations. Varying the amount of experimental data available for emulator calibration showed clear differences in the degree of uncertainty and uniqueness of the resulting optimized Johnson-Cook parameters for Al-5083. The results of the optimization provided a numerical evaluation of the degree of confidence in model parameters and model performance. Lastly, given an understanding of the physical effects of certain model parameters, individual parameter uncertainty can be leveraged to quickly identify gaps in the physical domains covered by completed experiments.
Modeling and simulation of the dynamic response of materials is important to many applications including the development of armor systems, understanding the safety of explosives, and assessing the crashworthiness of vehicles. Within such applications it is often critical to accurately compute the evolution of the temperature because it is a state variable that affects the kinetics of competing active processes within the material (e.g., dislocation motion, phase transformation, decomposition). Depending on the selection of an independent state variable, e.g. temperature or entropy, the approach for computing temperature is well understood based on the thermodynamic framework attributed to Coleman and Noll. However, different computational codes used for modeling the dynamic response of materials adopt different independent state variables. In this work, two thermodynamically consistent strategies for computing the temperature of a coupled thermodynamic state are compared and implemented into two different Lagrangian computational codes. The equivalence of these two approaches is established through the numerical solutions of several test problems. Finally, the implication of various approximations made to each of these approaches within the literature are assessed in the context of uniaxial stress conditions (split Hopkinson pressure bar experiments) and uniaxial strain conditions (plate impact experiments). Here, it is shown that the temperature rate or energy partition approaches are equivalent when implemented in their complete forms, but that several common simplifying assumptions, that are warranted in the case of uniaxial stress, lead to significant errors in the resulting Hugoniot state for plate impact.
Here, this article presents results from laser-driven shock compression experiments performed on pre-heated pure aluminum films at temperatures ranging from 23 to 400 °C. The samples were vapor deposited on the surface of a 500 μm thick sapphire substrate and mounted onto a custom holder with an integrated ring-heater to enable variable initial temperature conditions. A chirped pulse amplified laser was used to generate a pulse for both shocking the films and for probing the free surface velocity using Ultrafast Dynamic Ellipsometry. The particle velocity traces measured at the free surface clearly show elastic and plastic wave separation, which was used to estimate the decay of the elastic precursor amplitude over propagation distances ranging from 0.278 to 4.595 μm. Elastic precursors (which also correspond to dynamic material strength under uniaxial strain) of increasing amplitudes were observed with increasing initial sample temperatures for all propagation distances, which is consistent with expectations for aluminum in a deformation regime where phonon drag limits the mobility of dislocations. The experimental results show peak elastic amplitudes corresponding to axial stresses of over 7.5 GPa; estimates for plastic strain-rates in the samples are of the order 10 9 /s. The measured elastic amplitudes at the micron length scales are compared with those at the millimeter length-scales using a two-parameter model and used to correlate the rate sensitivity of the dynamic strength at strain-rates ranging from 10 3 to 10 9 /s and elevated temperature conditions. The overall trend, as inferred from the experimental data, indicates that the temperature-strengthening effect decreases with increasing plastic strain-rates.