Search NASA⌕ Search

Engineering topics

Bolotin, Gary S.

Publications and source records attributed to Bolotin, Gary S..

14 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2020

An embedded planar-foil capacitor material, FPGA based interposer, aimed at improving system performance and reduced board size for space based electronics

This paper presents work to date in developing, and testing an embedded planar-foil capacitor based interposer intended to be integrated together with high-density components such as Field Programmable Gate Arrays (FPGAs), and Application Specific Integrated Circuits (ASIC). FPGA devices typically have a large number of I/O and power pins. The high speed enabled by these devices requires a large number of discrete bypass capacitors as close as possible to the power pins. These capacitors take up a considerable amount of the board area on the application circuit board. The developed interposer replaces these components freeing up space of traditional bypass capacitors for other circuitry.

Cheng, Ben↗
NASA NTRS2015

Radioisotope Power System Pool Concept

Advanced Radioisotope Power Systems (RPS) for NASA deep space science missions have historically used static thermoelectric-based designs because they are highly reliable, and their radioisotope heat sources can be passively cooled throughout the mission life cycle. Recently, a significant effort to develop a dynamic RPS, the Advanced Stirling Radioisotope Generator (ASRG), was conducted by NASA and the Department of Energy, because Stirling based designs offer energy conversion efficiencies four times higher than heritage thermoelectric designs; and the efficiency would proportionately reduce the amount of radioisotope fuel needed for the same power output. However, the long term reliability of a Stirling based design is a concern compared to thermoelectric designs, because for certain Stirling system architectures the radioisotope heat sources must be actively cooled via the dynamic operation of Stirling converters throughout the mission life cycle. To address this reliability concern, a new dynamic Stirling cycle RPS architecture is proposed called the RPS Pool Concept.

Power↗
NASA NTRS2015

Test Program for Stirling Radioisotope Generator Hardware at NASA Glenn Research Center

Stirling-based energy conversion technology has demonstrated the potential of high efficiency and low mass power systems for future space missions. This capability is beneficial, if not essential, to making certain deep space missions possible. Significant progress was made developing the Advanced Stirling Radioisotope Generator (ASRG), a 140-W radioisotope power system. A variety of flight-like hardware, including Stirling convertors, controllers, and housings, was designed and built under the ASRG flight development project. To support future Stirling-based power system development NASA has proposals that, if funded, will allow this hardware to go on test at the NASA Glenn Research Center. While future flight hardware may not be identical to the hardware developed under the ASRG flight development project, many components will likely be similar, and system architectures may have heritage to ASRG. Thus, the importance of testing the ASRG hardware to the development of future Stirling-based power systems cannot be understated. This proposed testing will include performance testing, extended operation to establish an extensive reliability database, and characterization testing to quantify subsystem and system performance and better understand system interfaces. This paper details this proposed test program for Stirling radioisotope generator hardware at NASA Glenn. It explains the rationale behind the proposed tests and how these tests will meet the stated objectives.

Energy Conversion↗
NASA NTRS2014

Test Program for Stirling Radioisotope Generator Hardware at NASA Glenn Research Center

Stirling-based energy conversion technology has demonstrated the potential of high efficiency and low mass power systems for future space missions. This capability is beneficial, if not essential, to making certain deep space missions possible. Significant progress was made developing the Advanced Stirling Radioisotope Generator (ASRG), a 140-watt radioisotope power system. A variety of flight-like hardware, including Stirling convertors, controllers, and housings, was designed and built under the ASRG flight development project. To support future Stirling-based power system development NASA has proposals that, if funded, will allow this hardware to go on test at the NASA Glenn Research Center (GRC). While future flight hardware may not be identical to the hardware developed under the ASRG flight development project, many components will likely be similar, and system architectures may have heritage to ASRG. Thus the importance of testing the ASRG hardware to the development of future Stirling-based power systems cannot be understated. This proposed testing will include performance testing, extended operation to establish an extensive reliability database, and characterization testing to quantify subsystem and system performance and better understand system interfaces. This paper details this proposed test program for Stirling radioisotope generator hardware at NASA GRC. It explains the rationale behind the proposed tests and how these tests will meet the stated objectives.

Energy Conversion↗
NASA NTRS2011

NEXUS Scalable and Distributed Next-Generation Avionics Bus for Space Missions

A paper discusses NEXUS, a common, next-generation avionics interconnect that is transparently compatible with wired, fiber-optic, and RF physical layers; provides a flexible, scalable, packet switched topology; is fault-tolerant with sub-microsecond detection/recovery latency; has scalable bandwidth from 1 Kbps to 10 Gbps; has guaranteed real-time determinism with sub-microsecond latency/jitter; has built-in testability; features low power consumption (< 100 mW per Gbps); is lightweight with about a 5,000-logic-gate footprint; and is implemented in a small Bus Interface Unit (BIU) with reconfigurable back-end providing interface to legacy subsystems. NEXUS enhances a commercial interconnect standard, Serial RapidIO, to meet avionics interconnect requirements without breaking the standard. This unified interconnect technology can be used to meet performance, power, size, and reliability requirements of all ranges of equipment, sensors, and actuators at chip-to-chip, board-to-board, or box-to-box boundary. Early results from in-house modeling activity of Serial RapidIO using VisualSim indicate that the use of a switched, high-performance avionics network will provide a quantum leap in spacecraft onboard science and autonomy capability for science and exploration missions.

He, Yutao↗
NASA NTRS2006

Micro-Inspector Avionics Module (MAM): A Self-Contained Low Power, Reconfigurable Avionics Platform for Small Spacecrafts and Instruments

This paper describes development of a radiation tolerant, low power, reconfigurable avionics module aimed at meeting the avionics needs of the JPL Micro-Inspector spacecraft. This module represents a complete avionics system, consisting of two PowerPC 405 CPUs embedded within a reconfigurable FPGA fabric of over 8 Million logic gates, 64MB of EDAC protected Flash storage and 128MB of EDAC protected DDR SDRAM or SDRAM memories, along with FPGA SEU mitigation logic, and all necessary power conversion. Processor SEU mitigation is achieved by running the two processors in a lock-step and compare configuration. All of these building blocks are integrated into a double sided circuit board that takes as little as 6 square inches of board space. This module can be embedded into a user system as part of a bigger circuit assembly or as a self contained module. This module is being developed as part of a JPL led Micro-Inspector Program, funded by NASA ESMD aimed at producing a 10Kg micro spacecraft.

configurable↗
NASA NTRS2004

IBM powerPC 405 SEU mitigation using processor voting techniques in Xilinx Virtex-I1 pro FPGA

Not until recently, Xilinx has developed a new field programmable gate array (FPGA) device family, Virtex-I1 Pro. In this single device, not only dies it have density logic cells (3K to125K), gigabit connectivity, on chip memory, digital clock management, but also it can have up to four IBM PowerPC 405 Processor hard cores, running up to 400MHz and 633 Mbps. To utilize this cutting edge device in space applications, a few Single Event Upset (SEU) mitigation techniques need to be implemented to a design for the device. At Jet Propulsion Laboratory (JPL), we have successfully demonstrated the feasibility of running multiple processors running in a lock step fashion to accomplish SEU mitigation and fault tolerance.

single event upset (SEU)↗
NASA NTRS2001

Three-dimensional modular electronic interconnection system

A three-dimensional connection system uses a plurality of printed wiring boards with connectors completely around the printed wiring boards, and connected by an elastomeric interface connector. The device includes internal space to allow room for circuitry. The device is formed by stacking an electronics module, an elastomeric interface board on the electronics module such that the interface board's exterior makes electrical connection with the connectors around the perimeter of the interface board, but the internal portion is open to allow room for the electrical devices on the printed wiring board. A plurality of these devices are stacked between a top stiffener and a bottom device, and held into place by alignment elements.

Bolotin, Gary S.↗
NASA NTRS1998

Parallel processing spacecraft communication system

An uplink controlling assembly speeds data processing using a special parallel codeblock technique. A correct start sequence initiates processing of a frame. Two possible start sequences can be used; and the one which is used determines whether data polarity is inverted or non-inverted. Processing continues until uncorrectable errors are found. The frame ends by intentionally sending a block with an uncorrectable error. Each of the codeblocks in the frame has a channel ID. Each channel ID can be separately processed in parallel. This obviates the problem of waiting for error correction processing. If that channel number is zero, however, it indicates that the frame of data represents a critical command only. That data is handled in a special way, independent of the software. Otherwise, the processed data further handled using special double buffering techniques to avoid problems from overrun. When overrun does occur, the system takes action to lose only the oldest data.

Bolotin, Gary S.↗
NASA NTRS1996

Stackable Electronic Computer Modules And Interconnections

Design concept for multiprocessor computer system calls for digital electronic processing circuits of various functionalities contained within identically shaped and sized regular polygonal modules interconnected and stacked by use of rings around edges. Rings contain wide-band bus circuits configured to provide connections to adjacent modules in same layer of stack and/or to modules in different layers. Provides flexibility of configuration to implement any of large variety of designs.

Bolotin, Gary S.↗
NASA NTRS1990

Distributed computing system with dual independent communications paths between computers and employing split tokens

This is a distributed computing system providing flexible fault tolerance; ease of software design and concurrency specification; and dynamic balance of the loads. The system comprises a plurality of computers each having a first input/output interface and a second input/output interface for interfacing to communications networks each second input/output interface including a bypass for bypassing the associated computer. A global communications network interconnects the first input/output interfaces for providing each computer the ability to broadcast messages simultaneously to the remainder of the computers. A meshwork communications network interconnects the second input/output interfaces providing each computer with the ability to establish a communications link with another of the computers bypassing the remainder of computers. Each computer is controlled by a resident copy of a common operating system. Communications between respective ones of computers is by means of split tokens each having a moving first portion which is sent from computer to computer and a resident second portion which is disposed in the memory of at least one of computer and wherein the location of the second portion is part of the first portion. The split tokens represent both functions to be executed by the computers and data to be employed in the execution of the functions. The first input/output interfaces each include logic for detecting a collision between messages and for terminating the broadcasting of a message whereby collisions between messages are detected and avoided.

Rasmussen, Robert D.↗
NASA NTRS1989

Balanced-Load Real-Time Multiprocessor System

Modularity and parallelism provide tolerance to faults and high throughput capacity. System, called MAX, is network of interconnected computers. MAX cluster consists of group of modules - each semiautonomous computer. Modules connected to each other and to other clusters by global bus and circuit-switched communication mesh.

Rasmussen, Robert D.↗