Search NASA⌕ Search

Engineering topics

Borland, M

Publications and source records attributed to Borland, M.

At least 19 records

Status of the Short-Pulse X-ray Project at the Advanced Photon Source

The Advanced Photon Source Upgrade (APS-U) Project at Argonne will include generation of short-pulse x-rays based on Zholents deflecting cavity scheme. We have chosen superconducting (SC) cavities in order to have a continuous train of crabbed bunches and flexibility of operating modes. In collaboration with Jefferson Laboratory, we are prototyping and testing a number of single-cell deflecting cavities and associated auxiliary systems with promising initial results. In collaboration with Lawrence Berkeley National Laboratory, we are working to develop state-of-the-art timing, synchronization, and differential rf phase stability systems that are required for SPX. Collaboration with Advanced Computations Department at Stanford Linear Accelerator Center is looking into simulations of complex, multi-cavity geometries with lower- and higher-order modes waveguide dampers using ACE3P. This contribution provides the current R&D status of the SPX project.

43 PARTICLE ACCELERATORS↗

Dynamic Aperture and Tolerances for PEP-X Ultimate Storage Ring Design

A lattice for the PEP-X ultimate storage ring light source, having 11 pm-rad natural emittance at a beam energy of 4.5 GeV at zero current, using 90 m of damping wiggler and fitting into the existing 2.2-km PEP-II tunnel, has been recently designed. Such a low emittance lattice requires very strong sextupoles for chromaticity correction, which in turn introduce strong non-linear field effects that limit the beam dynamic aperture. In order to maximize the dynamic aperture we choose the cell phases to cancel the third and fourth order geometric resonances in each 8-cell arc. Four families of chromatic sextupoles and six families of geometric (or harmonic) sextupoles are added to correct the chromatic and amplitude-dependent tunes. To find the best settings of the ten sextupole families, we use a Multi-Objective Genetic Optimizer employing elegant to optimize the beam lifetime and dynamic aperture simultaneously. Then we evaluate dynamic aperture reduction caused by magnetic field multipole errors, magnet fabrication errors and misalignments. A sufficient dynamic aperture is obtained for injection, as well as workable beam lifetime.

43 PARTICLE ACCELERATORS↗

SciDAC Advances in Beam Dynamics Simulation: From Light Sources to Colliders

In this paper, we report on progress that has been made in beam dynamics simulation, from light sources to colliders, during the first year of the SciDAC-2 accelerator project 'Community Petascale Project for Accelerator Science and Simulation (ComPASS).' Several parallel computational tools for beam dynamics simulation are described. Also presented are number of applications in current and future accelerator facilities (e.g., LCLS, RHIC, Tevatron, LHC, and ELIC). Particle accelerators are some of most important tools of scientific discovery. They are widely used in high-energy physics, nuclear physics, and other basic and applied sciences to study the interaction of elementary particles, to probe the internal structure of matter, and to generate high-brightness radiation for research in materials science, chemistry, biology, and other fields. Modern accelerators are complex and expensive devices that may be several kilometers long and may consist of thousands of beamline elements. An accelerator may transport trillions of charged particles that interact electromagnetically among themselves, that interact with fields produced by the accelerator components, and that interact with beam-induced fields. Large-scale beam dynamics simulations on massively parallel computers can help provide understanding of these complex physical phenomena, help minimize design cost, and help optimize machine operation. In this paper, we report on beam dynamics simulations in a variety of accelerators ranging from next generation light sources to high-energy ring colliders that have been studied during the first year of the SciDAC-2 accelerator project.

43 PARTICLE ACCELERATORS↗

X-ray Sources by Energy Recovered Linacs and Their Needed R&D

In this paper we review the current state of research on energy recovered linacs as drivers for future X-ray sources. For many types of user experiments, such sources may have substantial advantages compared to the workhorse sources of the present: high energy storage rings. Energy recovered linacs need to be improved beyond present experience in both energy and average current to support this application. To build an energy recovered linac based X-ray user facility presents many interesting challenges. We present summaries on the Research and Development (R&D) topics needed for full development of such a source, including the discussion at the Future Light Sources Workshop held in Gaithersberg, Maryland on September 15-17, 2009. A first iteration of an R&D plan is presented that is founded on the notion of building a set of succeedingly larger test accelerators exploring cathode physics, high average current injector physics, and beam recirculation and beam energy recovery at high average current. Our basic conclusion is that a reviewable design of such a source can be developed after an R&D period of reasonably short duration.

43 PARTICLE ACCELERATORS↗

Status of the Short-Pulse X-ray Project (SPX) at the Advanced Photon Source (APS)

The Advanced Photon Source Upgrade project (APS-U) at Argonne includes implementation of Zholents’* deflecting cavity scheme for production of short x-ray pulses. This is a joint project between Argonne National Laboratory, Thomas Jefferson National Laboratory, and Lawrence Berkeley National Laboratory. This paper describes performance characteristics of the proposed source and technical issues related to its realization. Ensuring stable APS storage ring operation requires reducing quality factors of these modes by many orders of magnitude. These challenges reduce to those of the design of a single-cell SC cavity that can achieve the desired operating deflecting fields while providing needed damping of all these modes. The project team is currently prototyping and testing several promising designs for single-cell cavities with the goal of deciding on a winning design in the near future. Here

43 PARTICLE ACCELERATORS↗

Multi-objective direct optimization of dynamic acceptance and lifetime for potential upgrades of the Advanced Photon Source.

The Advanced Photon Source (APS) is a 7 GeV storage ring light source that has been in operation for well over a decade. In the near future, the ring may be upgraded, including changes to the lattice such as provision of several long straight sections (LSS). Because APS beamlines are nearly fully built out, we have limited freedom to place LSSs in a symmetric fashion. Arbitrarily-placed LSSs will drastically reduce the symmetry of the optics and would typically be considered unworkable. We apply a recently-developed multi-objective direct optimization technique that relies on particle tracking to compute the dynamic aperture and Touschek lifetime. We show that this technique is able to tune sextupole strengths and select the working point in such a way as to recover the dynamic and momentum acceptances. We also show the results of experimental tests of lattices developed using these techniques.

43 PARTICLE ACCELERATORS↗

Monte Carlo simulation of Touschek effect.

We present a Monte Carlo method implementation in the code elegant for simulating Touschek scattering effects in a linac beam. The local scattering rate and the distribution of scattered electrons can be obtained from the code either for a Gaussian-distributed beam or for a general beam whose distribution function is given. In addition, scattered electrons can be tracked through the beam line and the local beam-loss rate and beam halo information recorded.

43 PARTICLE ACCELERATORS↗

Changes to the Advanced Photon Source storage ring as part of the APS renewal project

The Advanced Photon Source (APS) is a third-generation, storage-ring-based x-ray source that has been operating for more than 13 years and is enjoying a long period of stable, reliable operation. While APS is presently providing state-of-the-art performance to its large user community, we must clearly plan for improvements and upgrades to stay at the forefront scientifically. Significant improvements should be possible through upgrades of beamline optics, detectors, and end-station equipment. In this paper, we discuss the evolutionary changes that are envisioned for the storage ring itself. Among the possibilities are long straight sections, additional straight sections, higher current, short-pulse x-rays, improved insertion devices, and improved beam stability.

43 PARTICLE ACCELERATORS↗

Concepts and performance for a next-generation storage ring hard x-ray source

Among the possibilities for a next-generation hard x-ray source is a so-called 'ultimate storage ring'. This refers to a large, high-energy storage ring with very low emittance and high current. Such a ring has the potential to deliver significantly higher spectral brightness and transverse coherence than present third-generation rings. At the same time, it promises the stability and reliability that users have come to expect in a light source. In this paper, we present a design for a 7-GeV, 40-sector storage ring with a circumference of 3.1 km and an emittance of 15 pm in both planes.

43 PARTICLE ACCELERATORS↗

Symmetric long straight section lattices for 2, 4, and 8 sectors.

Long straight sections (LSS) are anticipated to be one of the significant changes to the accelerator as part of the APS Renewal. Previously, we developed a lattice with eight LSS that, while workable, would have presented some operational challenges. In the present note, we show improved results for 8LSS, along with new solutions for 4LSS and 2LSS. As before, these lattices are developed by removing the Q2 quadrupoles and moving the Q1 back into its place, permitting a 7.7-m-long insertion device (as judged by the increase in face-to-face distance for the innermost powered quadrupoles). Further increases in length (perhaps 10%) might be possible by removing corrector magnets, but at present we have not considered this in detail.

43 PARTICLE ACCELERATORS↗

Possibility of splitting APS dipoles to make more ID straights.

Recently we were asked by Ercan Alp if it would be possible to use three dipoles in an APS sector to make a second ID beamline possible, much as was done for the APSx3 design. We've looked at this to see what might be possible without making too many changes to the ring. Ideally, we'd like to simply replace the one dipole with two shorter dipoles with an insertion device in the middle. Of course, we'd like to make the ID as long as possible, subject to limits on dipole strength, accelerator optics, and emittance. We used elegant [3] to match an insertion device consisting of two sectors. The second (BM) dipole of the first sector was split at the 1/8th point in terms of both angle and length. A zero length drift space was inserted that could then be stretched to create room for an ID. To simplify matters somewhat at this stage, we constrained the length of the two dipoles plus the drift to equal the original dipole length. I.e., we ignored for now the difference between arc and straight length. Our desire is to make the drift space as long as possible. If we limit the dipole field B to 2T, then the total length of the dipoles must be greater than L{sub min} = H{theta}/B, where H = 23.35Tm is the rigidity and {theta} = {pi}/40-0.001 is the total angle. L{sub min} is therefore 0.91 m, and hence the drift space can at most be 2.15 m. At least one, perhaps both, of the short dipoles will end up in a high-dispersion region, which will lead to emittance growth. Hence, we didn't want to drive the length too far and decided to limit it to 2 m, approximately the same as in the APSx3 lattice. Hence, as in that lattice we should be able to accommodate a 1-m-long insertion device. In addition to stretching the drift space, we allowed all twenty quadrupoles in the sectors to vary. Initial constraints included less than 20% deviation in lattice functions at the middle ID straight and less than 0.001% deviation in the final ID straight (to get a good match to the rest of the ring). We found the dispersion slope at the middle ID was quite hard to match, and made this a relatively loose constraint. We also had to increase the tolerance on changes in the horizontal beta function at the middle ID from 20 to 30%. A constraint was also placed on the effective emittance to make it as small as possible. Figure 1 shows the lattice functions for the two sectors. The magnet-to-magnet distance between the split dipoles is 1.97 m, slightly short of the 2 m mark. The first dipole is 0.17 m long with a field of 1.35 T, while the second dipole is 0.92 m long with a field of 1.73 T. The effective emittance assuming we formed a ring from such sectors is 4.95 nm. Hence, if we add N such modules to a ring with all other sectors being normal (3.13 nm effective emittance), the expected emittance is 9.9N + (40-2N)3.13/40 (1). If we want to limit the emittance to 10% more than the nominal 3.13 nm, we need N < 4. If we limit it to under 4 nm (ESRF's emittance), then we have N < 10. Table 1 lists parameters of the new source point, assuming that we insert three such modules in the ring (N = 3) and that we have a 1.5% ratio of the raw emittances. We attempted to improve the emittance and matching by allowing a gradient in the dipoles, thinking that perhaps it would provide additional optics flexibility. However, no improvement was obtained.

43 PARTICLE ACCELERATORS↗

A low-emittance APS lattice with alternating horizontal beta functions at insertion devices.

Previously we looked at the possibility of reducing the horizontal beta function in a straight section in order to optimize the beam properties for certain uses. This is difficult to do as an insertion because of the many constraints on the APS lattice. In particular, the emittance inevitably increases, and it can only be done for one or two sectors. We noted in that an ESRF-style lattice with alternating high- and low-{beta}{sub s} sectors might provide reasonably good emittance for the APS, while providing two types of beta function. In this note, we present such a lattice that not only provides alternating {beta}{sub s}, but also improved emittance.

43 PARTICLE ACCELERATORS↗

Characterization and mitigation of coherent optical transition radiation signal from a compressed electron beam.

The Advanced Photon Source (APS) injector complex includes an option for rf photocathode (PC) gun beam injection into the 450-MeV S-band linac. At the 150-MeV point, a four-dipole chicane was used to compress the micropulse bunch length from a few ps to sub-0.5 ps (FWHM). Noticeable enhancements of the optical transition radiation (OTR) signal sampled after the APS chicane were then observed as has been reported in the Linac Coherent Light Source (LCLS) injector commissioning. A far-infrared (FIR) coherent transition radiation detector and interferometer were used to monitor the bunch compression process and correlate the appearance of localized spikes of OTR signal (5 to 10 times brighter than adjacent areas) within the beam-image footprint. We have performed spectral-dependency measurements at 375 MeV with a series of bandpass filters centered in 50-nm increments from 400 to 700 nm and with an imaging spectrometer and observed a broadband enhancement in these spikes. Mitigation concepts of the observed coherent OTR, which exhibits an intensity enhancement in the red part of the visible spectrum as compared to incoherent OTR, are described.

43 PARTICLE ACCELERATORS↗

SciDAC advances in beam dynamics simulation: from light sources to colliders

In this paper, we report on progress that has been made in beam dynamics simulation, from light sources to colliders, during the first year of the SciDAC-2 accelerator project 'Community Petascale Project for Accelerator Science and Simulation (ComPASS).' Several parallel computational tools for beam dynamics simulation are described. Also presented are number of applications in current and future accelerator facilities (e.g., LCLS, RHIC, Tevatron, LHC, and ELIC).

Qiang, J↗

Automated correction of phase errors in the Advanced Photon Source linac.

Maintaining stable phasing in a linear accelerator is crucial for maintaining optimal performance. If phasing is incorrect, the beam will in general have an energy error and increased energy spread. While an energy error can be readily detected and corrected using position readings from beam position monitors at dispersion locations, this method is not useful for correcting energy spread in a system with many possible phase errors. While energy spread can be corrected by looking at beam size at a dispersive location, this typically involves a beam-intercepting diagnostic and is not compatible with top-up operation. Uncorrected energy spread results in poor capture efficiency in downstream accelerators, such as the Advanced Photon Source (APS) particle accumulator ring or booster synchrotron. To address this issue, APS has implemented beam-to-rf phase detectors in the linac, along with software for automatic correction of phase errors. We discuss the design, implementation, and performance of these detectors, as well as their use in feedback to automatically correct linac phase errors during top-up operation.

43 PARTICLE ACCELERATORS↗