Search NASA⌕ Search

Engineering topics

Bradley C Buckles

Publications and source records attributed to Bradley C Buckles.

9 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2024

Development of a Surface Water Transportation System for ISRU Operations on Mars

NASA is working to define the architecture needed for a Mars exploration campaign. Initial analysis assumptions allow for pre-deployment of essential cargo and equipment to support a crew landing, including the pre-positioning of a Mars Ascent Vehicle (MAV). This MAV is likely to represent the largest single payload that must be landed on the Mars surface. Its size would be influenced by the amount of mass that state-of-the-art Entry, Descent, and Landing (EDL) systems would be capable of placing on Mars. One possible method of increasing the usable size of the MAV without exceeding available EDL capabilities is to land the MAV without ascent propellant on board. Following such a method may necessitate a strategy to acquire sufficient ascent propellant to allow a crew to safely depart the Martian surface. This paper describes a conceptual return propellant strategy that uses a liquid transportation skid, or pallet, to be used in conjunction with a rover mobility system to transfer water across the Martian surface from a source point to an in-situ resource utilization (ISRU) plant that would use this water as a feedstock to generate oxygen and methane to enable launch of the MAV. Design considerations, concept of operations, and rover energetics will be discussed in this paper.

Fluid Structure Interface↗
NASA NTRSDate not supplied

ICE-RASSOR: Intelligent Capabilities Enhanced Regolith Advanced Surface Systems Operations Robot

NASA’s Regolith Advanced Surface Systems Operations Robot (RASSOR) is principally designed to mine and deliver regolith for In-Situ Resource Utilization (ISRU)processing. RASSOR’s design enables it to efficiently collect and deposit regolith, return collected material for processing, and myriad related ISRU activities. To reliably perform these operations on the lunar surface, RASSOR software and sensory systems need to be robust and maximize the information extracted from a reduced sensor payload. Herein, we present preliminary findings from the Intelligent Capabilities Enhanced RASSOR project. We apply supervised learning using real data to estimate the soil mass collected without the need for mass flow rate monitors or other explicate sensing techniques. We also create a reduced-order simulation environment to develop autonomous trenching controllers via reinforcement learning and prototype state estimation architectures. Our initial results suggest that excavated regolith mass can be inferred within 2.9% RMS error of full scale, and reinforcement learning for autonomous operations has learned viable trenching strategies and helped identify desirable sensing capabilities, arrangements, and considerations. Future work includes regolith mass estimation during dynamic operation, expanding our simulation to more complex environments, and transfer learning from simulation to hardware.

machine learning↗
NASA NTRSDate not supplied

Lunar Landing and Launch Pad Construction – Concepts and Criteria

When a lander vehicle launches or lands on the Moon, the rocket engine exhaust plume impinges on the surface and interacts with the regolith to create blast ejecta and associated cratering of the surface. Lunar regolith blast ejecta travels at high velocities (>2,000 m/s) for long distances (kilometers) in a vacuum environment [1] creating hazards for surrounding assets and it can also impact the bottom of the lander vehicle, risking damage to the engines, thermal insulation and sensors. Ballistic particles can possibly enter cislunar space and achieve orbit as debris, if the ejecta is sufficiently energetic. The cratering and regolith erosion can endanger the vehicle itself by affecting the soil stability under the landing gear. Landing on unpredictable terrain with varying topography, natural craters and rock hazards is also hazardous risks tipping a lander at dangerous angles in extreme conditions that may also violate maximum slope angles for subsequent launch operations. During launch (Figure 1), an overpressure pulse created by the ignition of the rocket engines can pose significant ejecta risks to the vehicle. Dust clouds raised during landing limit the efficacy of sensors and reduce visibility for the astronaut pilots, creating significant real-time risk during landing site selection by the pilot or computer navigation system. Future lunar spaceports will require mitigations to these launch and landing risks [2]. There are four main objectives of this effort:1) To establish the state of the art in LLP construction methodologies. 2) To propose criteria for trade studies of LLP concepts. 3) To publicly share the authors’ ideas for potential LLP solutions. 4) To serve as the starting point for future development of LLP technologies. Establishing the state of the art in the area of off-Earth Launch & Landing Pad concepts will base-line the work that has been completed thus far and highlight the wide span between current Technology Readiness Levels (TRLs)and operational readiness. The authors aim to communicate the need for funding in this area in the near term by illustrating that there is much work to be completed before a truly viable option exists. Setting forth criteria for trade studies of LLP concepts is important for several reasons. The first and most straightforward is to establish a framework for performing trade studies on LLP concepts. This will enable NASA to select the most promising concepts for continued development, and it will also help technology developers understand how their concepts compare with others and the priorities of development effort.

landing pad↗
NASA NTRSDate not supplied

In-situ Lunar Launch and Landing Pad Construction with Regolith-Thermoset Polymer Composite Materials

Lunar launch and landing pads are necessary to mitigate risks to lander/ascent vehicles and surrounding surface assets from rocket plume ejected regolith. The current state of the art of landing and launching from the lunar surface is to land/launch on unprepared regolith surfaces. Though this has been a relatively successful approach, significant risks exist for the Artemis Program due to higher thrust levels leading to increased ejecta and cratering, presence of co-located assets in the ejecta path, and potential strict surface levelness requirements. Regolith-thermoset polymer composite materials were developed and evaluated for off Earth launch and landing pad applications. Performance under hot fire conditions was assessed for two simulated Starship lunar launch/landing environments, one targeting thermal conditions and the second targeting pressure conditions. Paver test articles were prepared at 20% and 11% polymer mass fractions. Sintered paver test articles were prepared with 20% polymer grouting filling the seams between pavers. Though significant erosion was experienced during the more extreme thermal testing conditions, all test articles successfully mitigated regolith ejecta from plume effects. A concept for preparing and emplacing the materials was developed and tested in laboratory conditions. The testing evaluated the feasibility of using twin and single screw extruder technology to mix, convey and deposit materials. Both the twin and single screw extruders were capable of processing and extruding the composite with a maximum of 90% mass fraction of regolith achieved by the twin screw extruder.A primary risk for application of regolith-thermoset polymer composites as lunar launch/landingpad is the mass of polymer required to be landed on the moon. Calculations were performed that show that a 100 m diameter, 0.025 m thick pad with polymer mass fraction of 15% will require a payload mass of 72 mt to the Lunar surface. This is below the planned Starship payload capacity to the lunar surface of 100 mt. The regolith-thermoset polymer composite based construction approach proved feasibility in three critical areas: performance under launch/landing conditions, demonstration of a mixing and depositing strategy, and fitting within the planned lunar payload capacity. It is recommended that materials and systems be developed to TRL 6 for a small-scale lunar demonstration of emplacement of a launch/landing pad via a CLPS mission to support Artemis Program roadmap gap closure activities.

ISRU↗
NASA NTRSDate not supplied

Mass Inferencing Model Creation and Deployment to the RASSOR Lunar Excavation Robot

The Regolith Advanced Surface Systems Operations Robot (RASSOR) Excavator is a mobile robotic bucket-drum excavator platform with a unique space regolith excavation capability. The Intelligent Capabilities Enhanced RASSOR research project developed functionality for estimating the quantity of regolith mass ingested during RASSOR operation, enhancing RASSOR’s ability to successfully complete In-Situ Resource Utilization (ISRU) missions. To teleoperate or run autonomously, it is crucial for the amount of regolith mass ingested to be available as a system state for efficient operation. For example, during autonomous operation, RASSOR should navigate and move to a processing plant to offload the collected regolith when the drums are full; without knowledge of the total mass in the drums, this type of high-level planning is not possible. Three distinct modeling approaches were employed in developing a mass inferencing approach that could work on RASSOR, none of which require modification to the hardware. All take in system states, such as arm/drum motor positions, velocities, currents, voltages, and robot pose, and output a mass prediction for each set of the robot’s bucket drums. The developed models run in real-time, outputting predictions for the front drum mass, rear drum mass, timestamp of the last prediction, and total drum mass (sum of front and rear) in RASSOR’s drums. Models deployed to the hardware have low error (<7.5% mean error over the mass range, and <2.6% mean error when drums are more than half full) when making predictions in real-time. Our modeling approach can be adapted to use lunar excavation data to create models that are reflective of RASSOR’s dynamics when operating on the lunar surface. The results of this work are promising and show that models can be developed to accurately estimate excavated regolith mass.

Bucket Drum Excavators↗
NASA NTRSDate not supplied

Mass Inferencing Model Creation and Deployment to the RASSOR Lunar Excavation Robot

The Regolith Advanced Surface Systems Operations Robot (RASSOR) Excavator is a mobile robotic bucket-drum excavator platform with a unique space regolith excavation capability. The Intelligent Capabilities Enhanced RASSOR research project developed functionality for estimating the quantity of regolith mass ingested during RASSOR operation, enhancing RASSOR’s ability to successfully complete In-Situ Resource Utilization (ISRU) missions. To teleoperate or run autonomously, it is crucial for the amount of regolith mass ingested to be available as a system state for efficient operation. For example, during autonomous operation, RASSOR should navigate and move to a processing plant to offload the collected regolith when the drums are full; without knowledge of the total mass in the drums, this type of high-level planning is not possible. Three distinct modeling approaches were employed in developing a mass inferencing approach that could work on RASSOR, none of which require modification to the hardware. All take in system states, such as arm/drum motor positions, velocities, currents, voltages, and robot pose, and output a mass prediction for each set of the robot’s bucket drums. The developed models run in real-time, outputting predictions for the front drum mass, rear drum mass, timestamp of the last prediction, and total drum mass (sum of front and rear) in RASSOR’s drums. Models deployed to the hardware have low error (<7.5% mean error over the mass range, and <2.6% mean error when drums are more than half full) when making predictions in real-time. Our modeling approach can be adapted to use lunar excavation data to create models that are reflective of RASSOR’s dynamics when operating on the lunar surface. The results of this work are promising and show that models can be developed to accurately estimate excavated regolith mass.

bucket drum excavators↗