Engineering topics

Braithwaite, W. M.

Publications and source records attributed to Braithwaite, W. M..

16 records

NASA NTRS1986

Uniform engine testing program phase 7: NASA Lewis Research Center second entry

The propulsion and Energetics Panel, Working Group 15, of the Advisory Group for Aerospace Research and Development (AGARD) is sponsoring a Uniform Engine Testing Program (UETP). In this program, two jet engines were tested under identical conditions in certain NATO altitude and ground-level facilities as a means of correlating these facilities. With this second entry, NASA documented engine deterioration that may have occurred since inception of the UETP. Additionally, NASA investigated anomalies discovered during review of data from the five facilities which had participated in the program between the two NASA entries.

Biesiadny, T. J.↗

NASA NTRS1986

Summary of investigations of engine response to distorted inlet conditions

A survey is presented of experimental and analytical experience of the NASA Lewis Research Center in engine response to inlet temperature and pressure distortions. This includes a description of the hardware and techniques employed, and a summary of the highlights of experimental investigations and analytical modeling. Distortion devices successfully simulated inlet distortion, and knowledge was gained about compression system response to different types of distortion. A list of NASA research references is included.

Biesiadny, T. J.↗

NASA NTRS1979

Combined pressure and temperature distortion effects on internal flow of a turbofan engine

The flow characteristics obtained experimentally for the compression of a 2-spool TF30-P-3 turbofan engine operating with 180 grad combined pressure and temperature distortion in the inlet flow are presented. The analytical model (Mazzawy and Banks, 1976), 'tuned' during Lewis testing, was used for pretest predictions of the effects that these distortions would have on the engine flow characteristics and the limiting distortion values. The effect of inlet flow distortion on the performance of the engine is discussed, including: (1) the flow between a screen mounted in the inlet duct and the inlet guide vanes; (2) the flow through the compression system; and (3) the effects of the combined distortion and its orientation on the compressor stability limits. It is concluded that the model used in this program was capable of predicting the effects of total pressure, total temperature and combined total pressure-total temperature distortions in terms of flow profiles, inlet flow angles and attenuation of the distortions through the compressor system. It was also capable of predicting the trends of the limiting values experienced with various orientations of the combined distortions.

Braithwaite, W. M.↗

NASA NTRS1979

Combined pressure and temperature distortion effects on internal flow of a turbofan engine

An additional data base for improving and verifying a computer simulation developed by an engine manufacturer was obtained. The multisegment parallel compressor simulation was designed to predict the effects of steady-state circumferential inlet total-pressure and total-temperature distortions on the flows into and through a turbofan compression system. It also predicts the degree of distortion that will result in surge of the compressor. The effect of combined 180 deg square-wave distortion patterns of total pressure and total temperature in various relative positions is reported. The observed effects of the combined distortion on a unitary bypass ratio turbofan engine are presented in terms of total and static pressure profiles and total temperature profiles at stations ahead of the inlet guide vanes as well as through the fan-compressor system. These observed profiles are compared with those predicted by the complex multisegment model. The effects of relative position of the two components comprising the combined distortion on the degree resulting in surge are discussed. Certain relative positions required less combined distortion than either a temperature or pressure distortion by itself.

Braithwaite, W. M.↗

NASA NTRS1977

Effect of slotted casing treatment with change in Reynolds number index on performance of a jet engine

A tip-treated J85-13 engine was tested at Reynolds number indices (RNI) of 0.3 and 0.7 with a clean inlet for 80- and 100-percent corrected engine speeds. This engine was equipped with a compressor case which allowed changes to the case wall over the rotor tips of six of its eight stages. For all tests, the principal effects were (1) with tip treatment, a stall pressure ratio loss of 6 percent at 100 percent corrected engine speeds for both the 0.3 and 0.7 RNI, and (2) with and without tip treatment, decreasing the RNI from 0.7 to 0.3 decreased the stall pressure ratio 3.8 percent for 100 percent corrected engine speed and 2.8 percent for 80-percent corrected engine speed.

Moss, J. E., Jr.↗

NASA NTRS1977

Internal flow characteristics of a multistage compressor with inlet pressure distortion

The measured distribution of compressor interstage pressures and temperatures resulting from a 180 deg inlet-total-pressure distortion for a J85-13 turbojet engine is reported. Extensive inner stage instrumentation combined with stepwise rotation of the inlet distortion gave data of high circumferential resolution. The steady-state pressures and temperatures along with the amplitude, extent, and location of the distorted areas are given. Data for 80, 90, and 100 percent of rotor design speed are compared with clean (undistorted) inlet flow conditions to show pressure and temperature behavior within the compressor. Both overall and stagewise compressor performances vary only slightly when clean and distorted inlet conditions are compared. Total and static pressure distortions increase in amplitude in the first few stages of the compressor and then attenuate fairly uniformly to zero at the discharge. Total-temperature distortion induced by the pressure distortion reached a maximum amplitude by the first two stages and decayed only a little through the rest of the compressor. Distortion amplitude tended to peak in line with the screen edges, and, except for total and static pressure in the tip zone, there was little swirl in the axial direction.

Debogdan, C. E.↗

NASA NTRS1974

Summary of recent investigations of inlet flow distortion effect on engine stability

A review is presented of recent experimental results, analytical procedures and test techniques employed to evaluate the effects of inlet flow distortion on the stability characteristics of representative afterburning turbofan and turbojet compression systems. Circumferential distortions of pressure and temperature, separately and in combination are considered. Resulting engine sensitivity measurements are compared with predictions based on simplified parallel compressor models and with several distortion descriptor parameters.

Graber, E. J., Jr.↗

NASA NTRS1974

Summary of recent investigations of inlet flow distortion effects on engine stability

A review is presented of recent experimental results, analytical procedures and test techniques employed to evaluate the effects of inlet flow distortion on the stability characteristics of representative afterburning turbofan and turbojet compression systems. Circumferential distortions of pressure and temperature, separately and in combination, are considered. Resulting engine sensitivity measurements are compared with predictions based on simplified parallel compressor models and with several distortion descriptor parameters.

Graber, E. J., Jr.↗

NASA NTRS1973

Experimental evaluation of a TF30-P-3 turbofan engine in an altitude facility: Effect of steady-state temperature distortion

The effects of circumferential distortion of the total temperature entering 25, 50, and 75 percent of the inlet circumferential annulus of a turbofan engine were determined. Complete compressor stall resulted from distortions of from 14 to 20 percent of the face averaged temperature. Increasing the temperature level in one sector resulted in that sector moving toward stall by decreasing the equivalent rotor speeds while the pressure ratio remained approximately constant. Stall originated as a rotating zone in the low-pressure compressor which resulted as a terminal stall in the high-pressure compressor. Decreasing the Reynolds number index to 0.25 from 0.5 reduced the required distortion for stall by 50 percent for the conditions investigated.

Braithwaite, W. M.↗

NASA NTRS1973

The effect of inlet temperature and pressure distortion on turbojet performance

The effects on stability of steady-state, 180 degree extent circumferential distortions of inlet total temperature and pressure were experimentally determined for a turbojet engine. Results for both individual and combined temperature and pressure distortions are presented showing the losses incurred in stall pressure ratio and are compared with results predicted using a simplified parallel compressor model. The loss due to combined distortions was dependent upon the relative orientation between the low pressure and high temperature regions. Reasonable agreement was achieved between the predicted and observed loss in stall pressure ratio when based on a constant corrected speed relationship.

Braithwaite, W. M.↗

NASA NTRS1973