Search NASA⌕ Search

Engineering topics

Braun, Paul V.

Publications and source records attributed to Braun, Paul V..

At least 19 records

Composition-Nanoarchitecture-Performance Analysis of High Energy Density Electrodeposited Silicon for Lithium-Ion Battery Anodes

Electrodeposition of silicon (Si) was previously demonstrated as a promising method for fabricating 3D-structured lithium-ion battery anodes. However, the relationship between the electrochemical performance and chemical composition of the relatively impure electrodeposited silicon is not well understood. Here, we report the electrodeposition of a Si-dominant active material (EDEP-Si) onto 3D-structured nickel (Ni) scaffolds and systematically compare the electrochemical properties, elemental composition, atomistic Si coordination, and molecular structure of EDEP-Si with high-purity amorphous Si grown via static chemical vapor deposition. Despite the considerable amount of carbon (9–11 at %) and oxygen (42–44 at %) present in EDEP-Si, the cycling stability and high reversible specific capacity are remarkably similar to those of CVD-Si on a silicon basis (~2400 mA h/g-Si after 100 cycles). The primary difference is that EDEP-Si exhibits reduced cycling efficiency over the first 10–20 cycles. Reactions between carbon and, more importantly, oxygen in EDEP-Si with lithium are likely responsible for the reduced early cycle performance and lower capacity of the total deposit. Finally, our observations suggest ultrapure Si is not necessary for high electrochemical access to reversible charge storage, although limiting the presence of incorporated impurity species would improve energy density and first cycle efficiency.

25 ENERGY STORAGE↗

Ionic Peltier effect in Li-ion electrolytes

The coupled transport of charge and heat provide fundamental insights into the microscopic thermodynamics and kinetics of materials. We describe a sensitive ac differential resistance bridge that enables measurements of the temperature difference on two sides of a coin cell with a resolution of better than 10 μK. We use this temperature difference metrology to determine the ionic Peltier coefficients of symmetric Li-ion electrochemical cells as a function of Li salt concentration, solvent composition, electrode material, and temperature. The Peltier coefficients Π are negative, i.e., heat flows in the direction opposite to the drift of Li ions in the applied electric field, large, –Π > 30 kJ mol –1 , and increase with increasing temperature at T > 300 K. The Peltier coefficient is approximately constant on time scales that span the characteristic time for mass diffusion across the thickness of the electrolyte, suggesting that heat of transport plays a minor role in comparison to the changes in partial molar entropy of Li at the interface between the electrode and electrolyte. Here, our work demonstrates a new platform for studying the non-equilibrium thermodynamics of electrochemical cells and provides a window into the transport properties of electrochemical materials through measurements of temperature differences and heat currents that complement traditional measurements of voltages and charge currents.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Highly Ordered Eutectic Mesostructures via Template‐Directed Solidification within Thermally Engineered Templates

Template-directed self-assembly of solidifying eutectics results in emergence of unique microstructures due to diffusion constraints and thermal gradients imposed by the template. Here, the importance of selecting the template material based on its conductivity to control heat transfer between the template and the solidifying eutectic, and thus the thermal gradients near the solidification front, is demonstrated. Simulations elucidate the relationship between the thermal properties of the eutectic and template and the resultant microstructure. The overarching finding is that templates with low thermal conductivities are generally advantageous for forming highly organized microstructures. When electrochemically porosified silicon pillars (thermal conductivity < 0.3 Wm −1 K −1 ) are used as the template into which an AgCl-KCl eutectic is solidified, 99% of the unit cells in the solidified structure exhibit the same pattern. In contrast, when higher thermal conductivity crystalline silicon pillars (≈100 Wm −1 K −1 ) are utilized, the expected pattern is only present in 50% of the unit cells. The thermally engineered template results in mesostructures with tunable optical properties and reflectances nearly identical to the simulated reflectances of perfect structures, indicating highly ordered patterns are formed over large areas. This work highlights the importance of controlling heat flows in template-directed self-assembly of eutectics.

36 MATERIALS SCIENCE↗

A Self‐Healing System for Polydicyclopentadiene Thermosets

Self-healing offers promise for addressing structural failures, increasing lifespan, and improving durability in polymeric materials. Implementing self-healing in thermoset polymers faces significant manufacturing challenges, especially due to the elevated temperature requirements of thermoset processing. To introduce self-healing into structural thermosets, the self-healing system must be thermally stable and compatible with the thermoset chemistry. This article demonstrates a self-healing microcapsule-based system stable to frontal polymerization (FP), a rapid and energy-efficient manufacturing process with a self-propagating exothermic reaction (≈200 °C). A thermally latent Grubbs-type complex bearing two N-heterocyclic carbene ligands addresses limitations in conventional G2-based self-healing approaches. Under FP's elevated temperatures, the catalyst remains dormant until activated by a Cu(I) co-reagent, ensuring efficient polymerization of the dicyclopentadiene (DCPD) upon damage to the polyDCPD matrix. The two-part microcapsule system consists of one capsule containing the thermally latent Grubbs-type catalyst dissolved in the solvent, and another capsule containing a Cu(I) coagent blended with liquid DCPD monomer. Using the same chemistry for both matrix fabrication and healing results in strong interfaces as demonstrated by lap-shear tests. In an optimized system, the self-healing system restores the mechanical properties of the tough polyDCPD thermoset. Self-healing efficiencies greater than 90% via tapered double cantilever beam tests are observed.

36 MATERIALS SCIENCE↗

Reversible Reactions, Mesh Size, and Segmental Dynamics Control Penetrant Diffusion in Ethylene Vitrimers

The diffusion of two aromatic dyes with nearly identical sizes was measured in ethylene vitrimers with precise linker lengths and borate ester cross-links using fluorescence recovery after photobleaching (FRAP). One dye possessed a reactive hydroxyl group, while the second was inert. The reaction of the hydroxyl group with the network is slow relative to the hopping times of the dye, resulting in a large slowdown by a factor of 50 for a reactive probe molecule. A kinetic model was fit to the fluorescence intensity data to determine rate constants for the reversible reaction of the dye from the network, which confirms the role of slow reaction kinetics. A second network cross-linker was also investigated with a substituted boronic ester showing ∼10,000 times faster exchange kinetics. In this system, the two dyes show the same diffusion coefficient, as the reaction is no longer the rate-limiting step. The role of dense meshes on small and large dyes is also discussed in the context of the existing theories. Finally, these results highlight the potential of dynamic networks to control penetrant transport through synergistic effects of the mesh size, dynamic bond kinetics, and penetrant–network interactions.

confinement↗

Thermally Responsive Hydrogels for Passive Temperature Regulation under Direct Sunlight

By spontaneously emitting midinfrared radiation to outer space through the atmospheric window and reflecting sunlight, daytime radiative coolers achieve notable passive cooling performance. However, existing daytime radiative cooling systems generally lack the ability to adaptively switch between heating and cooling states based on ambient conditions. Herein a passive thermal regulation system that features a temperature‐dependent switchable solar reflectance from 0.05 (low temperature) to 0.8 (high temperature) is presented. This, along with a ≈0.95 midinfrared emittance, it enables automatic switching between radiative cooling and solar heating. Switchablity is enabled using a poly( N ‐isopropylacrylamide) (PNIPAM) hydrogel which exhibits high solar scattering above its tunable lower critical solution temperature (LCST) and transparency below its LCST. The lower part of the hydrogel is loaded with graphite to absorb solar energy in the heating state. In testing under sunny and partly cloudy outside conditions, this system maintains a temperature close to the set LCST.

Xie, Dajie↗

Electrically switchable metallic polymer metasurface device with gel polymer electrolyte

Abstract We present an electrically switchable, compact metasurface device based on the metallic polymer PEDOT:PSS in combination with a gel polymer electrolyte. Applying square-wave voltages, we can reversibly switch the PEDOT:PSS from dielectric to metallic. Using this concept, we demonstrate a compact, standalone, and CMOS compatible metadevice. It allows for electrically controlled ON and OFF switching of plasmonic resonances in the 2–3 µm wavelength range, as well as electrically controlled beam switching at angles up to 10°. Furthermore, switching frequencies of up to 10 Hz, with oxidation times as fast as 42 ms and reduction times of 57 ms, are demonstrated. Our work provides the basis towards solid state switchable metasurfaces, ultimately leading to submicrometer-pixel spatial light modulators and hence switchable holographic devices.

36 MATERIALS SCIENCE↗

Static and Dynamic Gradient Based Directional Transportation of Neutral Molecules in Swollen Polymer Films

Abstract Materials which selectively transport molecules offer powerful opportunities for concentrating and separating chemical agents. Here, utilizing static and dynamic chemical gradients, transport of molecules within swollen crosslinked polymers is demonstrated. Using an ≈200 μm static hydroxyl to hexyl gradient, the neutral ambipolar nerve agent surrogate diethyl (cyanomethyl)phosphonate (DECP) is directionally transported and concentrated 60‐fold within 4 hours. To accelerate transport kinetics, a dynamic gradient (a “travelling wave”) is utilized. Here, the non‐polar dye pyrene was transported. The dynamic gradient is generated by an ion exchange process triggered by the localized introduction of an aqueous NaCl solution, which converts the gel from hydrophobic to hydrophilic. As the hydrophilic region expands, associated water enters the gel, and pyrene is pushed ahead of the expansion front. The dynamic gradient provides about 10‐fold faster transport kinetics than the static gradient.

Ali, Mohammad A.↗

Static and Dynamic Gradient Based Directional Transportation of Neutral Molecules in Swollen Polymer Films

Abstract Materials which selectively transport molecules offer powerful opportunities for concentrating and separating chemical agents. Here, utilizing static and dynamic chemical gradients, transport of molecules within swollen crosslinked polymers is demonstrated. Using an ≈200 μm static hydroxyl to hexyl gradient, the neutral ambipolar nerve agent surrogate diethyl (cyanomethyl)phosphonate (DECP) is directionally transported and concentrated 60‐fold within 4 hours. To accelerate transport kinetics, a dynamic gradient (a “travelling wave”) is utilized. Here, the non‐polar dye pyrene was transported. The dynamic gradient is generated by an ion exchange process triggered by the localized introduction of an aqueous NaCl solution, which converts the gel from hydrophobic to hydrophilic. As the hydrophilic region expands, associated water enters the gel, and pyrene is pushed ahead of the expansion front. The dynamic gradient provides about 10‐fold faster transport kinetics than the static gradient.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Chemical Amplification of Subthreshold Base Triggers To Drive Sol–Gel Transitions in Polymers

Chemical amplification has been widely applied in applications ranging from stimuli sensing to advanced photoresists, but it is rarely utilized to drive productive mechanical property changes. Here, we demonstrate the use of a base amplifier to drive the gelation of a functional polymer solution, in response to a subthreshold base trigger through a mechanism whereby the trigger drives a dramatic increase in the base concentration driven by base amplification, resulting in complexation of Fe(III) and polymer-bound catechol groups and subsequent gelation of the polymer solution. Furthermore, the concomitant crystallization of dibenzofulvene, which is a byproduct of base amplification, led to significant stiffening of the resultant gel and an unexpected temperature-sensitive change of gel stiffness.

Aromatic compounds↗

Linear and nonlinear viscoelasticity of concentrated thermoresponsive microgel suspensions

We present an integrated experimental and theoretical study of the dynamics and rheology of self-crosslinked, slightly charged, temperature responsive soft poly(N-isopropylacrylamide) (pNIPAM) microgels over a wide range of concentration and temperature spanning the sharp change in particle size and intermolecular interactions across the lower critical solution temperature (LCST). Dramatic, non-monotonic changes in viscoelasticity are observed as a function of temperature, with distinct concentration dependence in the dense fluid, glassy, and soft-jammed regimes. Motivated by our experimental observations, we formulate a minimalistic model for the size dependence of a single microgel particle and the change of the interparticle interaction from purely repulsive to attractive upon heating. Using microscopic equilibrium and time-dependent statistical mechanical theories, theoretical predictions are quantitatively compared with experimental measurements of the shear modulus. Good agreement is found for the nonmonotonic temperature behavior that originates as a consequence of the competition between reduced microgel packing fraction and increasing interparticle attractions. Furthermore, testable predictions are made for nonlinear rheological properties such as the yield stress and strain. To our knowledge, this is the first attempt to quantitatively understand in a unified manner the viscoelasticity of dense, temperature-responsive microgel suspensions spanning a wide range of temperatures and concentrations.

42 ENGINEERING↗

High Energy Density and Stable Three-Dimensionally Structured Se-Loaded Bicontinuous Porous Carbon Battery Electrodes

Here, 3D structured Se-loaded bicontinuous porous carbon (BPC) electrodes were fabricated through colloidal templating of BPC followed by pulsed-voltage Se electrodeposition. The resultant electrodes were found to deliver a specific capacity of 665 mA h g -1 at a rate of 0.1 C, near the theoretical value for Se. When a vinylene carbonate containing electrolyte was utilized, the capacity fade over 500 cycles at 1 C rate was as small as a few percent. Impedance measurements and physical characterization of cycled electrodes indicated the exceptionally stable cycling performance was possibly due to vinylene carbonate resulting in formation of a stable SEI during cycling. Along with cycling stability, the rate performance of the 3D Se/BPC electrodes was also good. Due to the bicontinuous structure of carbonaceous current collector at rates as high as 5 C, the deliverable capacity was about 300 mA h g -1 .

25 ENERGY STORAGE↗

Ultralow Thermal Conductivity in Nanoporous Crystalline Fe 3 O 4

While there is no known fundamental lower limit to the thermal conductivity of a material, the lowest thermal conductivities are typically found in amorphous and strongly disordered materials, not highly crystalline materials. Here, we demonstrate a surprising nanostructuring route to ultralow thermal conductivity in a large-unit-cell oxide crystal (Fe 3 O 4 ) containing close-packed nanoscale pores. The electrical conductivity of this material reduces by a factor of 5 relative to dense v, independent of pore size. In contrast, thermal conductivity has a strong dependence on pore size with a factor of 40 of suppression relative to dense Fe 3 O 4 for 40 nm pores vs a factor of 5 for 500 nm pores. The matrix thermal conductivity of Fe 3 O 4 containing 40 nm pores falls below the predicted minimum thermal conductivity by a factor of 3. Finally, we attribute this to strong acoustic phonon scattering and intrinsically limited contributions to thermal conductivity from optical phonons with small dispersion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗