Search NASA⌕ Search

Engineering topics

Brett R. Hiller

Publications and source records attributed to Brett R. Hiller.

9 records
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Design Exploration of a Slotted-Wing Common Research Model

A knowledge-based aerodynamic design method, Constrained Direct Iterative Surface Cur-vature (CDISC), has been leveraged for the computational design exploration of a Common Research Model with Reduced-Sweep and Slotted Wings (CRMRS-SW). Cruise-slotted-wing airfoils include a slot near the trailing edge of a main airfoil component to introduce stream air to the low-momentum, upper-surface boundary layer on a flap airfoil component with the goal of allowing for a more aft loading, relative to supercritical airfoils, without shock-induced separation. Ultimately, the cruise slotted wing is a passive technology that allows for an in-crease in the drag divergence Mach number and/or an increase in aerodynamic efficiency at agiven cruise condition. These aerodynamic benefits may be realized at the vehicle level through a trade space that includes the following design options: increasing cruise Mach number, in-creasing wing thickness, decreasing wing sweep, increasing lift coefficient and/or decreasing drag coefficient. The present study aimed to evaluate the slotted-wing concept’s potential as adrag-saving technology in application to a single-aisle transonic transport aircraft at a given cruise condition. The CDISC design method was used to develop a better understanding of the slotted-wing design variables that have a significant impact on the variability in aircraft drag and leverage this newly-developed knowledge to quantify the aerodynamic performance benefits enabled by the cruise slotted wing.

Brett R. Hiller↗
NASA NTRSDate not supplied

Design of a Crossflow Attenuated Natural Laminar Flow Flight Test Article

This abstract includes preliminary information on the computational design and analysis of a flight test article. The flight test aims to experimentally validate the new Crossflow Attenuated Natural Laminar Flow (CATNLF) design method in a flight environment. The CATNLF design method uses geometry shaping to produce specific pressure distributions that enable laminar flow on vehicle components with high sweep and high Reynolds numbers by attenuating the crossflow growth that typically leads to premature transition on such components. The flight test article design is scheduled to be completed at the end of 2019, with model fabrication beginning in early 2020.Design results presented in this abstract are representative of the final test article. The final paper will be updated to include the finalized test article geometry and analysis.

Michelle N. Lynde↗
NASA NTRSDate not supplied

Design of a Crossflow Attenuated Natural Laminar Flow Flight Test Article

A natural laminar flow test article has been designed and analyzed for a flight test at the NASA Armstrong Flight Research Center using the F-15 aircraft with Centerline Instrument Pylon (CLIP) testbed. The flight test aims to experimentally validate the new Crossflow Attenuated Natural Laminar Flow (CATNLF) design method in a flight environment. The CATNLF design method uses geometry shaping to produce specific pressure distributions that enable laminar flow on vehicle components with high sweep and high Reynolds numbers by attenuating the crossflow growth that typically leads to premature transition on such components. The CATNLF test article, which will be mounted vertically below the F-15 for flight testing, is designed to be representative of a transonic transport wing and accounts for transition mechanisms due to crossflow, Tollmien-Schlichting, and attachment line transition instabilities. The test article is predicted to support 53% surface area of laminar flow on the suction-side at the design point and maintains significant laminar flow extents at near-cruise, off-design conditions. The design was performed, flight matrix selected, and instrumentation chosen with two primary test goals in mind: to confirm the effectiveness of the CATNLF method in attenuating crossflow growth on a representative transonic transport wing, and to investigate surface requirements needed for laminar flow applications.

Michelle N. Lynde↗
NASA NTRSDate not supplied

CDISC Remote Design Method to Simulate Aircraft Interference Effects for the CATNLF Flight Test

The Crossflow Attenuated Natural Laminar Flow (CATNLF) flight test is an experimental evaluation of a laminar flow design approach that will be conducted on a small transonic wing-like model suspended from the Centerline Instrumented Pylon (CLIP) underneath an F-15 vehicle. The upcoming flight test is anticipated to provide experimental data that may be useful for transition prediction code calibrations or laminar flow computational studies. For the computational results to be reliable, relevant aerodynamics must be included in the simulations. It has been shown that the F-15 vehicle produces a notable aerodynamic influence on the CATNLF test article, and that removing the F-15 vehicle from the simulation significantly alters the laminar flow behavior. Because the F-15 vehicle is not a publicly-releasable geometry, if the CATNLF flight test dataset is to be widely used by the community, an alternative method to ensure that the CATNLF test article flight configuration aerodynamics is properly modeled is required. The objective of this research is to use the CDISC aerodynamic design tool to perform a remote design of a surface that would replicate the aerodynamic influence on the CATNLF test article. This new design approach, referred to as the Equivalent Loading via Interference Surface Effects (ELISE), is presented in this paper, including the details on the design setup and results. The ELISE design successfully reproduced the F-15 influence on the CATNLF test article, with predicted transition location within an average of 4% chord of the full flight configuration. An off-design assessment is included for small perturbations in Mach and sideslip angle that suggest the ELISE design can cover a reasonable range of expected flight conditions with the same geometry. This paper is intended to explain the design approach, as well as show results that can be expected when utilizing the ELISE design method.

CDISC↗
NASA NTRSDate not supplied

Transonic Cruise Slotted Wing Design for Commercial Transport Aircraft using CDISC

A knowledge-based aerodynamic design method, CDISC, has been extended to enable the computational design of transonic cruise slotted wings for commercial transport aircraft. The cruise slotted wing is a multielement wing concept with a forward main element and an aft flap element, separated to form an intermediate slot. This slot favorably redirects airflow from the main element lower surface toward the low-momentum, upper-surface boundary layer of the flap. Relative to the supercritical wing, the cruise slotted wing enables greater aft loading that helps to reduce shock strength and transonic pressure drag. The cruise slotted wing may be considered a passive drag reduction technology with potential fuel-burn savings and increased vehicle range for next-generation aircraft. The current paper seeks to quantify the drag-saving benefits of cruise slotted wing technology in application to single-aisle commercial transport aircraft. A series of multielement design constraints were developed within CDISC for the design of a partial-span, cruise slotted wing for a Mach-0.8 variant of the Common Research Model. To mitigate the skin-friction drag penalty associated with cruise slotted wings, the design features a flap with natural laminar flow over approximately 75% of the flap surface area. Cruise drag estimates from the NASA USM3D-ME flow solver between a supercritical wing and the partial-span, cruise slotted wing design were within one drag count. Near-cruise, off-design analyses showed limited laminar-flow sensitivity to angle of attack and a more gradual drag rise compared to a supercritical wing. Based on this observed benefit, future work is motivated to design a cruise slotted wing with laminar flow on both wing elements to achieve a significant reduction in cruise drag while delaying drag divergence.

CDISC↗
NASA NTRSDate not supplied

History and Status of the CDISC Aerodynamic Design Method

This paper will review the development and application of the CDISC aerodynamic design method that began in the early 1980s and continues in active use today. The method uses an iterative, knowledge-based approach that has been coupled with numerous flow solvers utilizing a variety of grid types and levels of flow physics. It has been applied to configurations varying in complexity from 2-D airfoils to full 3-D aircraft at flow conditions ranging from low-speed, high-lift to supersonic cruise. The knowledge-based approach provides a very rapid design process, with designs typically completed in approximately 1-2x the time required for an initial converged analysis of the baseline. The evolution of the method as it tracked the expansive growth of grid and flow solver technology, along with some major applications over 5 decades, are given, followed by a description of the philosophy and process used in design. Finally, an example of its use in a preliminary design environment is given.

CDISC↗
NASA NTRSDate not supplied

Application of the CATNLF Design Method to a Transonic Transport Empennage Using CDISC

A novel Crossflow Attenuated Natural Laminar Flow (CATNLF) design method has been developed to achieve laminar flow on aircraft empennage at transonic flight conditions. This approach has been applied to the design of a nonlifting vertical tail using CDISC, a knowledgebased aerodynamic design tool developed at the NASA Langley Research Center. A horizontal tail was also designed using an enhanced CATNLF design approach for low-lift components. CDISC was coupled with USM3D-ME, a Navier-Stokes computational fluid dynamics solver. Stability and transition software was used to determine the laminar extent on the surfaces. Results indicate laminar flow can be sustained at midcruise conditions to about x/c=0.40 on the vertical tail and as much as x/c=0.65 on the horizontal tail lower surface. Transonic longitudinal off-design analysis indicates minimal change in the laminar extent. However, nonzero sideslip angles at transonic conditions can cause premature transition relative to the midcruise condition.

Brent W. Pomeroy↗
NASA NTRSDate not supplied

History and Status of the CDISC Aerodynamic Design Method

This paper will review the development and application of the CDISC aerodynamic design method that began in the early 1980s and continues in active use today. The method uses an iterative, knowledge-based approach that has been coupled with numerous flow solvers utilizing a variety of grid types and levels of flow physics. It has been applied to configurations varying in complexity from 2-D airfoils to full 3-D aircraft at flow conditions ranging from low-speed, high-lift to supersonic cruise. The knowledge-based approach provides a very rapid design process, with designs typically completed in approximately 1-2x the time required for an initial converged analysis of the baseline. The evolution of the method as it tracked the expansive growth of grid and flow solver technology, along with some major applications over 5 decades, are given, followed by a description of the philosophy and process used in design. Finally, an example of its use in a preliminary design environment is given.

CDISC↗