Search NASA⌕ Search

Engineering topics

Brewer, Luke N.

Publications and source records attributed to Brewer, Luke N..

7 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Residual Stress in Cold Spray SS304L Measured Via Neutron Diffraction and Comparison of Analytical Models to Predict the Residual Stress

Here, this study employs neutron diffraction to investigate the relationship between residual stress and coating thickness in cold sprayed 304L austenitic stainless steel. Results show that shot peening predominantly impacts the residual stress profile, leading to substantial in-plane compressive force. The impact of laser heating, a widely used method to alter cold spray's microstructural properties, on the coating's residual stress is also analyzed. The findings indicate that the maximum compressive residual stress in the in-plane component is mainly independent of coating thickness, which suggests that the material properties determine the maximum residual stress. The cold sprayed deposits possessed compressive, nearly biaxial strain and stresses. After laser heating, these stresses were replaced by tensile residual stresses. Two analytical models, the Tsui and Clyne and the Boruah models, for predicting residual stresses are also evaluated, and both models provide reasonable fits to the experimental data. At this point, the deviations between the experimental results and the models are principally caused by the inability of the current models to address plastic deformation and relaxation, and the residual stresses generated by thermal gradients.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Influence of Molybdenum on Rapid Solidification Microstructure and Microsegregation in Primary Ferrite Solidified Stainless Steel

Due to the widespread use and familiarity of austenitic stainless steels in many industries these alloys are often the first materials used when adapting new processing techniques. The rapid cooling and solidification rates that occur during fusion based additive manufacturing processes like powder bed fusion cause a fundamental shift in the solidification behavior of the material. While the effects that Cr and Ni have on the microstructure have been fairly well documented across a range of solidification conditions, the impact of alloying elements like Mo are not as well understood at rapid solidification rates. For this study, four custom stainless steel alloy feedstocks were made with targeted modification of the Cr and Mo concentrations to maintain a constant Cr/Ni eq ratio of ~1.7. Two-piston splat quenching was used to produce rapidly solidified samples and the solidification mode, phase, and cell size were investigated. Solidification rates were estimated to be between 0.4 and 1.5m/s. A comparison of the microsegregation and partitioning behavior of Cr, Ni and Mo in ferrite solidified material was also performed for the different alloy compositions. Variations of the Mo concentration between each feedstock showed no measurable influence on the solidification/cooling rates, solidification morphology, or the partitioning of Mo. Furthermore, higher concentrations of Mo were found to significantly increase the amount of ferrite phase in the microstructure by suppressing the ferrite to austenite massive transformation.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Investigation of the Effect of Chrome and Nickel Concentrations During Two-Piston Splat Quenching of Austenitic Stainless Steels

For solidification rates at or near equilibrium solidification conditions the effects of chrome (Cr) and nickel (Ni) on stainless steel solidification modes and microstructures are well detailed. However, fusion-based additive manufacturing (FBAM) processes that rely on faster, more rapid solidification rates call for a more in-depth understanding of the effects of rapid solidification on the solidification behavior and how these change with variations in alloy composition. Eleven custom stainless steel (SS) alloys with unique compositions based on 316L were made using targeted alloying element additions to generate feedstock with Cr/Ni eq ratios ranging from 0.9 to 2.1. Two-piston splat quenching (SQ) was used to produce rapid solidification conditions similar to those achieved in powder bed fusion processes in a fraction of the time and cost of traditional methods. Employing heat transfer simulations, SEM, TEM, and STEM characterization techniques, the SQ process was found to consistently produce solidification rates estimated to be between ~ 0.4 and 1.6 m/s. Five unique solidification microstructures were identified within the rapidly solidified SQ samples (primary austenite, massively transformed ferrite to austenite, primary austenite and massively transformed ferrite to austenite, primary ferrite, and primary ferrite and massively transformed ferrite to austenite). Both the primary ferrite solidification mode and primary ferrite phase were found to form at lower Cr/Ni eq values than previously predicted. SQ samples with compositions that were within the compositional specifications for 316L SS, an alloy which is commonly used in FBAM processes, demonstrated a wider range of potential solidification modes and microstructures that could form at rapid solidification rates than expected. Finally, by using SQ as a means to simulate rapid solidification conditions similar to those observed in FBAM processes, potential new alloy compositions can be screened faster and more cost effectively than purchasing and running test batches of the metallic powder.

36 MATERIALS SCIENCE↗
DOE OSTI2023

A Comparison of Solidification Structures and Submicroscale Cellular Segregation in Rapidly Solidified Stainless Steels Produced via Two-Piston Splat Quenching and Laser Powder Bed Fusion

Fusion-based additive manufacturing techniques leverage rapid solidification (RS) conditions to create parts with complex geometries, unique microscale/nanoscale morphological features, and elemental segregation. Three custom composition stainless steel alloys with varying chromium equivalence to nickel equivalence ratio (Cr eq /Ni eq ) between 1.53 and 1.95 were processed using laser powder bed fusion (LPBF) and/or two-piston splat quenching (SQ) to produce solidification rates estimated between 0.4 and 0.8 m/s. Both scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were utilized to collect high-resolution images, electron backscatter diffraction (EBSD) phase identification, and measure cellular segregation. Similar features were observed in both LPBF and SQ samples including phase and microstructure, nanoscale oxide particles, cell size, and segregation behavior. However, dislocation pileup was observed along the cell boundaries only in the LPBF austenite solidified microstructure. Targeted adjustment of the SQ feedstock Cr and Ni concentrations, within the ASTM A240 specification for 316L resulted in no observable impact on the cell size, oxide particle size, or magnitude of segregation. Also, the amount of Ni segregation in the ferrite solidified microstructures did not significantly differ, regardless of Cr/Ni eq or processing technique. Here, SQ is demonstrated as capable of simulating RS rates and microstructures similar to LPBF for use as an alternative screening tool for new RS alloy compositions.

42 ENGINEERING↗
DOE OSTI2020

Neutron Diffraction Analysis of Residual Strain in High-Pressure Die Cast A383 Engine Blocks

The residual strains in three high-pressure die cast A383 engine blocks were measured using neutron diffraction. Residual strains and stresses can be generated during high-pressure die casting process due to high thermal gradients and may cause fatigue failure or dimensional distortion. Neutron diffraction can measure the residual strain distributions deep inside castings with complex geometries, because neutrons can penetrate substantially more material than x-rays. In this paper, the residual strains (in the axial and hoop directions) along the whole cylinder bridge of high-pressure die cast A383 engine blocks in as-cast and heat-treated conditions were measured by neutron diffraction methods. The effect of heat treatment on the distribution and magnitude of residual strains was also investigated. The results indicate that the residual strain in the cylinder bridge is tensile in both the axial and hoop components for both the as-cast and the heat-treated engine blocks. The residual strain in the hoop direction is bigger in magnitude than the residual strain in the axial direction. Heat treatment significantly relaxes the residual strain in the axial direction but only slightly relaxes the residual strain in the hoop direction.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Quantifying dislocation density in Al-Cu coatings produced by cold spray deposition

This work quantifies the plastic deformation in terms of dislocation density for a series of cold sprayed Al-Cu coatings with copper contents from 2 mass% to 5 mass%. The success of the deposition and consolidation of the feedstock powders during the cold spray process rely on the occurrence of significant plastic deformation. Inert gas atomized Al-Cu alloy powders were sprayed onto substrates made of an Al-Cu-Mg-Mn alloy (AA2024) to produce dense coatings using a low pressure cold spray system with helium as the carrier gas. X-ray diffraction patterns were obtained from the Al-Cu feedstock powder material and the cold sprayed coatings using a monochromatic X-ray source, and the dislocation density was determined via an X-ray whole profile analysis. Increasing the Cu alloy content (from 2 mass% to 5 mass%) systematically increased the dislocation density in the Al-Cu coatings from (4.3 ± 0.5) × 10 14 m -2 to (7.5 ± 0.8) × 10 14 m -2 . The dislocation densities in the feedstock powders ranging from (0.4 ± 0.1) × 10 14 m -2 to (1.8 ± 0.2) × 10 14 m -2 were all lower than the dislocation densities in the corresponding coatings. The increasing deformation level in the Al-Cu coatings with Cu additions were confirmed by the classic and modified Williamson-Hall analyses of X-ray diffraction data, and peak breadth measurements from neutron diffraction data. Finally, a high density of dislocations was also observed in these coatings via electron backscatter diffraction and transmission electron microscopy.

36 MATERIALS SCIENCE↗