Search NASA⌕ Search

Engineering topics

Brewer, W. D.

Publications and source records attributed to Brewer, W. D..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

X-ray diffraction measurements of residual stresses in SiC/Ti composites

Residual stresses are developed in metal matrix composites during consolidation because of the difference in the coefficient of thermal expansion of the fiber and matrix constituents. X-ray diffraction techniques were used to measure tensile residual stresses in the matrix component of two different titanium alloy composites reinforced with continuous silicon carbide fibers. The titanium alloy matrices were a beta-stabilized alloy Ti-15V-3Al-3Cr-3Sn, and an ordered multiphase (alpha + beta) alloy, Ti-14Al-21Nb. Residual tensile stresses as high as 62 percent of the yield of Ti-15V-3Al-3Cr-3Sn and 70 percent of the yield of Ti-14Al-21Nb were measured in the longitudinal direction on unidirectionally reinforced composites. By measuring residual stresses in four different composite lay-ups, the composite lay-up was determined to have a significant effect on the residual stress state near the surface.

Brown, K. M.↗
NASA NTRS1983

Solutal diffusion coefficient for liquid PbTe-SnTe

The solutal diffusion coefficient has been determined for liquid lead telluride-tin telluride using a modified shear cell technique. Postdiffusion concentration profiles are presented for several diffusion couples. The best analytical curve fit to the data gives a composition-dependent diffusion coefficient of (/3/7/ to the C power) x 0.00014 sq cm/sec, where C is the PbTe concentration. In addition, data are presented to show the importance of solutal convection in the lead-tin-telluride system.

Clark, I. O.↗
NASA NTRS1983

Metallurgical and tensile property analysis of several silicon carbide/titanium composite systems

Several silicon-carbide fiber reinforced titanium matrix composite systems were investigated to determine composite degradation mechanisms and to develop techniques to minimize loss of mechanical properties during fabrication and in service. Emphasis was on interface control by fiber or matrix coatings. Fibers and matrix materials were sputter coated with various metals to determine the effects of the coatings on basic fiber properties, fiber-matrix interactions, and on composite properties. The effects of limited variations in fabrication temperature on composite properties were determined for composites consolidated by standard press-diffusion-bonding techniques.

Brewer, W. D.↗
NASA NTRS1982

Interface control and mechanical property improvements in silicon carbide/titanium composites

Several composite systems made of titanium matrix reinforced with silicon carbide fiber were investigated to obtain a better understanding of composite-degradation mechanisms and to develop techniques to minimize loss of mechanical properties during fabrication and in service. Emphasis was on interface control by fiber or matrix coatings. X-ray diffraction studies on planar samples showed that the formation of titanium silicides was greatly inhibited by the presence of aluminum or Ti3A1 layers at the fiber-matrix interface, with the Ti3A1 being more effective in reducing the reactions. Fiber studies showed that coating the fiber with a 1-micron-thick layer of aluminum improved the as-fabricated strength of a stoichiometric SiC fiber and reduced the fiber degradation during exposure to composite-fabrication conditions. Applying an interfacial barrier by coating the matrix foils instead of the fibers was found to be an effective method for improving composite strength. Reducing the fabrication temperature also resulted in significant improvements in composite strengths. Good-quality, well-consolidated composites were fabricated at temperatures well below those currently used for SiC-Ti composite fabrication.

Brewer, W. D.↗
NASA NTRS1981

Modification of silicon carbide fibers for use in SiC/Ti composites

The degradation of silicon carbide fibers during exposure to conditions typical of composite fabrication was investigated. The tensile strength of pristine fibers and fibers sputtered with thin metal coatings were determined before and after treatment at 870 C for one hour in vacuum. Each fiber strength distribution was related by an analytical procedure to a projected composite ultimate tensile strength (PC UTS). The results indicate that a thin aluminum diffusion barrier can yield a 150 percent increase in PC UTS over the baseline SiC/Ti system.

Landis, H. S.↗
NASA NTRS1980

Preliminary Arc-Jet tests of ablator/RSI joints in simulated space shuttle ascent and entry heating

Five ablator/RSI panels were tested in simulated Shuttle heating conditions to determine heat pulse effects on the ablator and the ablator/RSI joints. Two of the panels were subjected to both ascent and entry heating. The other three panels were subjected to entry heating only. The double-pulse heating (ascent plus entry) had no significant effect on char-layer integrity. Evaluation of the effects of entry heating on the ablator/RSI joints was difficult because, with the panel configuration used, severe pressure gradients developed within some of the joints during testing causing hot-gas flow through the joints. In joints where pressure leaks apparently did not develop, temperatures within the joints were reasonable compared to ablator and RSI back surface temperatures.

Brewer, W. D.↗
NASA NTRS1980

An assessment of the readiness of ablative materials for preflight application to the shuttle orbiter

The shuttle orbiter relies primarily on a reusable surface insulation (RSI) thermal protection system (TPS). The RSI is very efficient in its thermal performance; however, the RSI tile system has shown poor mechanical integrity. The state-of-the-art of the ablative TPS is reviewed, and an assessment made of the ablator's readiness for use on the shuttle orbiter. Unresolved technical issues with regard to the ablative TPS are identified. Short time, highly focused analytical and experimental programs were initiated to: (1) identify candidate ablation materials; (2) assess the data base for these materials; (3) evaluate the need and kind of waterproof coating; (4) calculate thermal and other stresses in an ablator tile; (5) identify an acceptable ablator/RSI tile joint filler; and (6) assess the sensitivity of the ablator to sequential heat pulses. Results from some of these programs are discussed.

Tompkins, S. S.↗
NASA NTRS1979

Effects of boron and glass hybrid epoxy-composites on graphite-fiber release in an aircraft fire

Recent studies have shown that the benefits gained by using graphite-epoxy composite structures may not be realized without some risk. The graphite fibers are very good electrical conductors and fibers released into the environment during a fire create a possible hazard to electrical equipment. Several graphite-epoxy hybrids were exposed to a fire and simulated explosion and their graphite fiber retention characteristics were examined. Several low melting-temperature glasses which wet and clump graphite-fibers and a glass/graphite fabric which reduced impact damage were identified as promising hybridizing components to minimize graphite fiber release.

Tompkins, S. S.↗
NASA NTRS1979

Mechanical property degradation and chemical interactions in Borsic/titanium composite

A study was undertaken to identify the mechanisms of mechanical property degradation in a Borsic (silicon-carbide coated boron) fiber reinforced Ti-3Al-2.5V composite exposed to elevated temperature. Samples containing 0.45 volume fraction of fibers were exposed, in vacuum, to temperatures from 700 K to 1255 K for times up to 240 hours. Room temperature tensile properties of unidirectional material were determined in both the longitudinal and transverse directions, before and after high-temperature exposure. Electron micro-probe analysis, scanning electron microscopy, and X-ray diffraction were used to determine the compounds formed and the extent of interaction between the boron, SiC coating, and matrix materials.

Brewer, W. D.↗
NASA NTRS1979

Interfacial reactions in borsic/Ti-3Al-2-1/2V composite

The paper provides a detailed X-ray characterization of a borsic/Ti-3Al-2-1/2V composite, and to correlate the relative intensities of the reaction products with the mechanical properties. Based on X-ray integrated intensity data two stages of interface reactions were identified: during the first stage there is a simultaneous interdiffusion of Si, C, and Ti atoms at the filament/matrix interface resulting in the formation of Ti5Si3, TiSi and small amounts of TiSi2 and TiC. The second stage is associated with considerable TiSi2 and boride formation. It appears that the alpha-phase of Ti is more reactive in forming silicides and borides than the beta-phase. The silicide intensities and the reaction zone thicknesses are shown to be directly related to the reduction of the ultimate tensile strength by thermal degradation, and the results indicate that silicide reaction products are as detrimental to strength as the borides.

Rao, V. B.↗
NASA NTRS1978

Preliminary burn and impact tests of hybrid polymeric composites

Free graphite fibers released into the environment from resin matrix composite components, as a result of fire and/or explosion, pose a potential hazard to electrical equipment. An approach to prevent the fibers from becoming airborne is to use hybrid composite materials which retain the fibers at the burn site. Test results are presented for three hybrid composites that were exposed to a simulation of an aircraft fire and explosion. The hybrid systems consisted of 16 plies of graphite-epoxy with two plies of Kevlar-, S-glass-, or boron-epoxy on each face. Two different test environments were used. In one environment, specimens were heated by convection only, and then impacted by a falling mass. In the other environment, specimens were heated by convection and by radiation, but were not impacted. The convective heat flux was about 100-120 kW/m in both environments and the radiative flux was about 110 kW/sq m.

Tompkins, S. S.↗
NASA NTRS1977

Correction factors for on-line microprobe analysis of multielement alloy systems

An on-line correction technique was developed for the conversion of electron probe X-ray intensities into concentrations of emitting elements. This technique consisted of off-line calculation and representation of binary interaction data which were read into an on-line minicomputer to calculate variable correction coefficients. These coefficients were used to correct the X-ray data without significantly increasing computer core requirements. The binary interaction data were obtained by running Colby's MAGIC 4 program in the reverse mode. The data for each binary interaction were represented by polynomial coefficients obtained by least-squares fitting a third-order polynomial. Polynomial coefficients were generated for most of the common binary interactions at different accelerating potentials and are included. Results are presented for the analyses of several alloy standards to demonstrate the applicability of this correction procedure.

Unnam, J.↗
NASA NTRS1976

Graphite and ablative material response to CO2 laser, carbon-arc, and xenon-arc radiation

The behavior was investigated of graphite and several charring ablators in a variety of high-radiative heat-flux environments. A commercial-grade graphite and nine state-of-the-art charring ablators were subjected to various radiative environments produced by a CO2 laser and a carbon arc. Graphite was also tested in xenon-arc radiation. Heat-flux levels ranged from 10 to 47 MW/sq m. Tests were conducted in air, nitrogen, helium, and a CO2-N2 mixture which simulated the Venus atmosphere. The experimental results were compared with theoretical results obtained with a one-dimensional charring-ablator analysis and a two-dimensional subliming-ablator analysis. Neither the graphite nor the charring ablators showed significant differences in appearance or microstructure after testing in the different radiative environments. The performance of phenolic nylon and graphite was predicted satisfactorily with existing analyses and published material property data. Good agreement between experimental and analytical results was obtained by using sublimation parameters from a chemical nonequilibrium analysis of graphite sublimation. Some charring ablators performed reasonably well and could withstand radiative fluxes of the level encountered in certain planetary entries. Other materials showed excessive surface recession and/or large amounts of cracking and spalling, and appear to be unsuitable for severe radiative environments.

Brewer, W. D.↗
NASA NTRS1975

Interaction of graphite and ablative materials with CO2-laser, carbon-arc, and xenon-arc radiation

The behavior of graphite and several charring ablators in a variety of high radiative heat flux environments was studied in various radiative environments produced by a CO2 laser and a carbon arc facility. Graphite was also tested in xenon arc radiation. Tests were conducted in air nitrogen, helium, and a mixture of CO2 and nitrogen, simulating the Venus atmosphere. The experimental results are compared with theoretical results obtained with a one dimensional charring ablator analysis and a two dimensional subliming ablator analysis. Photomicroscopy showed no significant differences in appearance or microstructure of the charring ablators or graphite after testing in the three different facilities, indicating that the materials respond fundamentally the same to the radiation of different frequencies. The performance of phenolic nylon and graphite was satisfactorily predicted with existing analyses and published material property data.

Brewer, W. D.↗
NASA NTRS1972

Ablator manufacturing

Studies are being conducted to determine how manufacturing-induced defects affect the performance of ablative heat shields. If commonly occurring defects do not affect material performance, simpler manufacturing techniques can be used, quality control requirements can be relaxed, repair and rework operations can be held to a minimum, and thus the total manufacturing cost can be reduced.

Pittman, C. M.↗