Engineering topics

Brian H Mason

Publications and source records attributed to Brian H Mason.

11 records

NASA NTRS2023

A Tool for Defining Tow-Steered Laminates for Finite Element Grids

Tailoring of composite laminates is traditionally performed by changing the orientation of straight fibers in one or more plies. Modern automated fiber placement machines facilitate placement of bundles of curved fibers (tows) in a process called tow-steering, but additional variables must be used to define the shapes of tow-steered fiber paths. In this paper, a Python-based tool, called Automated Tool for Steered COmposite Optimizable Laminates (ATSCOOL), is presented for modeling steered tows as chains of circular arcs. The geometry for defining tow path shapes using four input variables is described. The formulae for determining gaps and overlaps between clusters of consecutive tows, called courses, and for determining the number of steered courses needed to cover a rectangular panel are presented. Graphical representation of courses and thickness distribution in an example panel using the ATSCOOL software are presented. Finally, an example of a finite element analysis performed using the property information output from ATSCOOL is shown.

finite element analysis↗

NASA NTRS2023

Finite Element Simulation of Three Full-Scale Crash Tests for Cessna 172 Aircraft

The NASA Emergency Locator Transmitter Survivability and Reliability project was initiated in 2013 to assess the crash performance standards for the next generation of emergency locator transmitter (ELT) systems. Three Cessna 172 aircraft were acquired to perform crash testing at the NASA Langley Research Center Landing and Impact Research Facility. Full-scale crash tests were conducted in the summer of 2015 and each test article was subjected to severe, but survivable, impact conditions including a flare-to-stall during emergency landing, and two controlled-flight-into-terrain scenarios. Finite element analyses were performed to numerically simulate the aircraft response to the crash tests. The first test simulated impacting a concrete surface represented analytically by a rigid plane. Tests 2 and 3 simulated impacting a dirt surface represented analytically by an Eulerian grid of bric k elements using a Mohr-Coulomb material model. The objective of this paper is to summarize the test and analysis results for the three full-scale crash tests. Simulation models of the airframe which correlate well with the tests are needed for future studies of alternate ELT mounting configurations.

Finite Element Analysis↗

NASA NTRS2022

Optimization Approach for Wind Tunnel Fan Blade Strain Gage Correlation with Test Fixture Unknowns

NASA has a significant maintenance challenge with the aging wind tunnel infrastructure across the Agency. Some wind tunnel fan blades, such as those in the National Transonic Facility at NASA Langley Research Center, have been in use for far longer than their planned 10-year lifetime. No detailed analytical models of the fan blades from their initial fabrication were created. To support the fabrication of either new, nominally identical fan blades or newly designed fan blades, accurate analytical models of the existing fan blades are necessary to demonstrate an understanding of the capabilities of the existing fan blades. Additionally, the existing documentation of the testing of the existing fan blades has gaps. In this report, a process for improving test-analysis correlation for these wind tunnel fan blades is discussed. This process involved a detailed study of unknown parameters in test fixture parameters from the old and incomplete test documentation. To improve correlation, these unknown parameters were used as design variables in an optimization study to minimize the error between test data and computed structural responses. Legacy strain gage data from tests conducted in 1981 were compared with results from a finite element model created in 2019. The use of test data from 1981 was necessary because none of the existing fan blades could be spared for use in destructive structural testing. While this process was demonstrated for wind tunnel fan blades, this process could be utilized for evaluating unknowns in test fixtures for other structural test configurations.

wind tunnel↗

NASA NTRS2020

Structural Analysis of Wind Tunnel Blades for the National Transonic Facility

NASA has a significant maintenance challenge with the agency’s aging wind tunnel infrastructure. Wind tunnel blades, such as the ones in the National Transonic Facility at NASA Langley Research Center, have been subjected to damage from impacts and fatigue. Accurate analytical models of these blades are necessary to either recertify replacement blades to be built or for redesign of these blades. In this paper a process for generating structural finite element models of these wind tunnel blades is presented. The model developed in this paper was analyzed under loading conditions from tests conducted on the original blades and the results are compared with legacy strain gage data.

Brian H Mason↗

NASA NTRSDate not supplied

Design of a Manufacturing Demonstration Unit for a Composite Lunar Landing Gear Strut

The goal of the current work was to develop an analytical framework for design of composite struts using various levels of model fidelity. An additional goal of this work was to perform an initial assessment of using automated fiber placement (AFP) and other advanced manufacturing methods to explore their feasibility for the fabrication of struts for lunar landers, strut-braced wings, and other aerospace components. In particular, designs were considered for fabrication at the Integrated Structural Assembly of Advanced Composites (ISAAC) facility at Langley Research Center (LaRC). The designs presented in this paper do not represent the exact geometry and material systems currently in use by the Artemis landing system, but they are considered to be representative. The designs produced during this study will be used to develop manufacturing demonstration units (MDU) that can be fabricated at ISAAC and tested in lab facilities at LaRC

carbon-epoxy↗

NASA NTRSDate not supplied

Design of a Manufacturing Demonstration Unit for a Composite Lunar Landing Gear Strut

The goal of the current work was to develop an analytical framework for design of composite struts using various levels of model fidelity. Rapid optimization trade studies were performed using low fidelity two-dimensional (2D) axisymmetric models with smeared composite properties. The optimum 2D model was compared with three-dimensional (3D) models with higher levels of fidelity in material property representation. Good agreement was found with all models. The buckling performance of the highest fidelity 3D model was found to be satisfactory for the intended loading conditions. An additional goal of this work was to perform an initial assessment of using automated fiber placement (AFP) and other advanced manufacturing methods to explore their feasibility for the fabrication of struts for lunar landers, strut-braced wings, and other aerospace components. The designs produced during this study are intended to be used to develop manufacturing demonstration units (MDU) that can be fabricated at the Integrated Structural Assembly of Advanced Composites (ISAAC) facility at Langley Research Center (LaRC) and tested in lab facilities at LaRC.

carbon-epoxy↗

NASA NTRSDate not supplied

Design of a Manufacturing Demonstration Unit for a Composite Lunar Landing Gear Strut

carbon-epoxy↗

NASA NTRSDate not supplied

Modal Test and Analysis Correlation of Wind Tunnel Blades for the National Transonic Facility

NASA has a significant maintenance challenge with the aging wind tunnel infrastructure across the agency . Wind tunnel blades, such as the ones in the National Transonic Facility at NASA Langley Research Center, have been subjected to damage from impacts and fatigue. Accurate analytical models of these blades are necessary to either recertify replacement blades to be built or for redesign of these blades. In this paper an upgraded finite element model of these wind tunnel blades with the capability of representing damage is presented. An eigenvalue analysis of the structural model is performed, and the boundary conditions are adjusted to simulate the natural frequencies obtained by experimental testing of a set of twenty five blades in 1992. Additional numerical studies of the effect of delamination damage on the natural frequencies of the blade are conducted using the tuned finite element model.

wind tunnel↗

NASA NTRSDate not supplied

Structural Sizing of a Composite Transonic Truss-Braced Wing

Accurate finite element modeling (FEM) is a vital part of the modern aircraft design process. As aircraft become increasingly complex, the time-consuming nature of detailed FEM approaches comes at a significant cost to program timeline and budget. In an effort produce modeling efforts that are sufficiently accurate and minimally costly, a proposed FEM approach and optimization scheme for a composite aircraft is explored, including a discussion of the manufacturing constraints of a highly tailored composite panel design. A high-fidelity structural model of a transonic truss-braced wing (TTBW) is generated, and the components are sized by structural optimization to satisfy buckling and strength constraints while subjected to critical maneuver loads. The structural modeling approaches and sizing of a TTBW are discussed, including details for FEM approaches, verification of an approximated FEM approach, a sizing optimization using the optimization software LS-OPT, and a manufacturing trial of integrally stiffened composite panels conducted to explore the validity of highly tailored composites as a design consideration. The results of study discussed herein indicate that the proposed FEM approach is suitable for modeling composite-construction aircraft and for use in sizing optimization. Further efforts regarding integrally stiffened composite panels will indicate the suitability of this method for the integration of highly tailored composite panels into the design and optimization process, given the manufacturability of such panels as shown here.

Finite Element↗

NASA NTRSDate not supplied

Structural Sizing of a Tow-Steered Truss-Braced Wing Box Test Article

Tailoring of composite laminates is traditionally performed by changing the orientation of straight fibers in one or more plies. Modern automated fiber placement machines facilitate placement of bundles of curved fibers (tows) in a process called tow-steering, but additional variables must be used to define the shapes of tow-steered fiber paths. In this paper, the design of a tow-steered truss-braced wing test article called the Structural Wing Experiment Evaluating Truss-bracing 15-ft concept (SWEET-15) is discussed. The SWEET-15 test article is scaled to 18.6% of the span length and chord width of a full-scale vehicle. The test article is designed to withstand +2.5-g (positive limit) and -1.0-g (negative limit) maneuvering loads with a factor of safety of 1.5 under strength and buckling constraints. Design studies were performed using commercial finite element analysis and optimization software in conjunction with a tow-steering modeling tool called ATSCOOL (Automated Tool for Steered COmposite Optimizable Laminates) developed at NASA Langley Research center. A 6.4% weight reduction in the upper cover panels was achieved using a tow-steered layup configuration.

Structural Optimization↗

NASA NTRSDate not supplied

Structural Sizing of a Tow-Steered Truss-Braced Wing Box Test Article

Tailoring of composite laminates is traditionally performed by changing the orientation of straight fibers in one or more plies. Modern automated fiber placement machines facilitate placement of bundles of curved fibers (tows) in a process called tow-steering, but additional variables must be used to define the shapes of tow-steered fiber paths. In this paper, the design of a tow-steered truss-braced wing test article called the Structural Wing Experiment Evaluating Truss-bracing 15-ft concept (SWEET-15) is discussed. The SWEET-15 test article is scaled to 18.6% of the span length and chord width of a full-scale vehicle. The test article is designed to withstand +2.5-g (positive limit) and -1.0-g (negative limit) maneuvering loads with a factor of safety of 1.5 under strength and buckling constraints. Design studies were performed using commercial finite element analysis and optimization software in conjunction with a tow-steering modeling tool called ATSCOOL (Automated Tool for Steered COmposite Optimizable Laminates) developed at NASA Langley Research center. A 6.4% weight reduction in the upper cover panels was achieved using a tow-steered layup configuration.

Composites↗