Recent Improvements to the LAURA and HARA Codes
Explore the source record for details and available documents.
LAURA HARA CFD 5.6↗
Engineering topics
Brian Hollis
Publications and source records attributed to Brian Hollis.
Improvements to the LAURA Mesh Adaptation Algorithm
This paper describes recent improvements to the LAURA code that removes the requirementof unbroken body-normal lines when using the automated mesh adaptation algorithm inLAURA responsible for mesh alignment with shock and adjusting near-wall mesh spacing. Fornon-simple geometry, restricting block topologies such that blocks span the domain from thesurface wall boundaries to domain inflow boundary can be difficult or impossible. Removing thisrequirement enables novel block topologies that simplify the meshing workflow for LAURA users.The new adaptation algorithm implementation in LAURA is described and several examples ofthe adaptation are presented to demonstrate the efficacy of the adaptation algorithm.
LAURA↗
Overview of Mars Sample Return – Earth Entry System Woven Roughness Heating Augmentation Test in NASA Langley’s Mach 6 Wind Tunnel
The Mars Sample Return Mission (MSR) is a planned NASA flagship mission in which a sample retrieval lander (SRL) with a rover will be flown to Mars to obtain sample tubes on the surface that were dropped by the Mars 2020 rover [1]. After obtaining the sam-ples, the rover will return and ascend back to Martian orbit onboard the Mars Ascent Vehicle (MAV). Upon return to Earth orbit, the samples will perform Entry, Descent, and Landing (EDL) with the Earth Entry Sys-tem (EES) architecture, and land in Utah. The EES vehicle will utilize a HEEET-variant as its TPS, which will be the first time a woven TPS will be used on a flagship NASA mission [2]. This TPS offers a unique challenge for Computational Fluid Dynamics (CFD) modeling of the aerothermal envi-ronment of the vehicle, as woven roughness heating augmentation has not been extensively investigated experimentally. As a result, in order to validate com-putational models for woven roughness heating aug-mentation, a wind tunnel test campaign at NASA Langley Research Center’s Mach 6 wind tunnel was performed in April of 2023. This test campaign consisted of over a hundred runs with Reynolds numbers spanning from 1-7 mil-lion 1/ft and with six separate wind tunnel models used. A second campaign with a suite of new models will be conducted in Summer 2023 as well as a cam-paign with a flat plate model, both of which are of great interest to the MSR-EES project. The data obtained from this test are extremely vital for the MSR mission, as they will validate CFD roughness heating models which will be directly used to design the TPS of the EES portion of MSR and characterize the heating environment that the entry ve-hicle will experience. Further extensions of the MSR-EES test campaign will continue to provide validation data for developing more effective computational tools.
Jonathan Cheatwood↗
Trajectory Reconstruction of the Low-Earth Orbit Flight Test of an Inflatable Decelerator
The Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) project conducted a flight test of a 6m inflatable aeroshell. The LOFTID test article was a secondary payload on an Atlas V launcher that carried the Joint Polar Satellite System-2 (JPSS-2) as its primary payload. The vehicle launched on November 10th, 2022. After reaching orbit, the LOFTID test article inflated the aeroshell, separated from the upper stage on an entry trajectory, and entered the atmosphere to splash down in the Pacific Ocean under parachutes. The test concept of operations is shown in Figure 1. The test article was instrumented with a variety of sensors to be used for post-flight evaluation of vehicle performance. Data from one of the key sensors for trajectory reconstruction, the Inertial Measurement Unit (IMU), was not captured in the data recorder due to a malfunction. Data from the nose cone mounted Flush Air Data Sensing (FADS) system were successfully acquired. The layout of the FADS sensors and the measured pressures during atmospheric entry are shown in Figure 2. The FADS data were combined with a Newtonian flow pressure model [1, 2] to produce estimates of the atmospheric relative trajectory. A Mach number anchoring technique given in [2] was used to stabilize estimates in high speed flight conditions. Since no IMU data were available, a trajectory simulation was used to provide the Mach number time history. The resulting estimates of the atmospheric-relative trajectory are shown in Figures 3. Given the loss of the IMU data, alternate methods for trajectory reconstruction are being explored. One approach under investigation is the use of the on-board video recorder data to be analyzed to reconstruct attitude motion. This approach is currently under investigation and will be reported on in the final paper. The Newtonian flow pressure model for the FADS analysis will also be updated with a CFD-based pressure model.
Christopher D Karlgaard↗
Mars Sample Return Earth Entry System Woven Roughness Mach 6 Aeroheating Test
The Mars Sample Return Earth Entry System is the first entry vehicle designed for a NASA flagship mission to utilize a woven thermal protection system as well as a 52.5 degree sphere cone forebody geometry. As a result, no heritage aeroheating experimental data set exists to compare with computational predictions. In order to obtain a set of validation data for computational models, an extensive wind tunnel test campaign was funded by the Mars Sample Return Earth Entry System project. The first entry in the test campaign was completed in April of 2023, which was an investigation of turbulent heating augmentation due to woven thermal protection system roughness on the 52.5 degree Mars Sample Return - Earth Entry System vehicle forebody geometry. This test entry produced the first ever experimental aeroheating data on a 52.5 deg sphere-cone geometry as well as the first NASA experimental aeroheating data on a woven surface roughness pattern. Data obtained from this test campaign is being directly leveraged to support the NASA flight program, as experimental results are being utilized to validate the computational models which characterize the aeroheating environment that the vehicle experiences and predict turbulent surface heating levels and margins across the woven surface.
Jonathan Cheatwood↗
Overview of Mars Sample Return Earth Entry System Angle-of-Attack Woven Roughness Aeroheating Test in NASA Langley's Mach 6 Wind Tunnel
Explore the source record for details and available documents.
Mars Sample Return↗
Aeroheating Predictions for a Hypersonic, Turbulent Near-Wake
The accuracy of heating predictions using various turbulence models is examined for an axisymmetric near-wake at Mach 6. The CFD predictions are compared with experimental data collected under AGARD Working Group 18 on the wake of a 70-degree sphere-cone. The impact of grid resolution and discretization error is estimated, which allows a comparison of stacked-block and conventional structured meshes. The accuracy of steady Reynolds-averaged Navier-Stokes (RANS) models is contrasted with that of a hybrid RANS/Large-Eddy Simulation model. The predictions are made with three different CFD codes (LAURA, FUN3D, and HyperSolve), to demonstrate the code-to-code variation in the results. Steady SST models capture the qualitative nature of the heating in the wake, including the increasing peak heating with increasing Reynolds number. Spalart-Allmaras models, including SA-Catris, under-predicted the peak heating in the wake. Hybrid RANS/LES models improve upon the SA results but have their own modeling difficulties near the shear layer impingement. These results are generally consistent across solvers and grid topologies.
RANS↗
Aeroheating Testing of the Mars Sample Return Earth Entry System with Surface Roughness
The Mars Sample Return Earth Entry System is a mission concept which would be the first NASA entry vehicle to utilize a woven thermal protection system as well as a 52.5 degree sphere-cone forebody geometry. Due to its novel design, historic experimental data sets were insufficient to validate the models used to characterize the expected aerothermal environment. A wind tunnel test campaign was funded by the Mars Sample Return Earth Entry System project in the NASA Langley 20-Inch Mach 6 Air Tunnel in order to obtain validation data. The December 2023 test entry of this campaign sought to obtain thermographic data to capture the impact of supersonic flow near woven surface roughness elements on convective heating augmentation, which was the largest remaining uncertainty in aerothermal design of the Earth Entry System. Data obtained were in family with prior results obtained on identical woven patterns without supersonic flow present at roughness elements, and it was found that this presence of supersonic flow did not have a noticeable effect on surface convective heating augmentation. Data were directly leveraged to support the NASA Mars Sample Return flight program and this data set is valuable for validating computational solutions on roughness-resolved grids.
Mars Sample Return↗