Search NASA⌕ Search

Engineering topics

Brian R Hollis

Publications and source records attributed to Brian R Hollis.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2024

Experimental and Computational Study of Convective Heating on the Aeroshell Back Side and Payload of the LOFTID Vehicle

A wind tunnel test program was conducted to obtain experimental convective heating data on models of the Low Earth Orbital Flight Test of an Inflatable Decelerator (LOFTID) vehicle in support of the flight test program. Wind tunnel testing was conducted at Mach 6 and Mach 10 at unit Reynolds numbers from 0.5×106/ft to 4.0×106/ft on 6.0inch diameter aeroshell models. Global heating data were obtained through phosphor thermography measurements on the front and back of the aeroshell and on the payload. For all test conditions, attached, laminar flow was definitively produced on the front of the aeroshell, while in the wake the flow was separated, unsteady and possibly transitional or turbulent. A complementary computational study was performed to assess the accuracy of heating predictions for LOFTID wake flow environments. A new grid topology was developed for the study to allow the use of structured grid solvers for complex, open-backed geometries such as that of LOFTID. Close agreement between measurements and predictions was obtained on the front of the aeroshell. Comparisons were more challenging in the wake because of both the extremely low heating rates and the accompanying high uncertainties and the unsteady nature of the separated wake flow simulations. While the differences between heating predictions and measurements for the wake flow were higher than for the forebody flow, these differences were used to assist in the definition of conservative uncertainty margins for predictions of the flight environments for the successful flight test of the LOFTID vehicle in November 2022.

LOFTID↗
NASA NTRS2024

Application of PLIF to Investigate the Hypersonic Wake of a LOFTID-Relevant Model at Mach 10

An experimental investigation of hypersonic wake flows using the planar laser-induced fluorescence (PLIF) measurement technique is summarized in this report. Off-body measurements, primarily flow visualization and velocity, were obtained for the wake of a blunt body model relevant for terrestrial re-entry and Martian entry applications within a Mach 10 hypersonic flow. The design of the model was based on the forebody aeroshell used for the LOFTID (Low-Earth Orbit Flight Test of an Inflatable Decelerator) flight vehicle. This document serves to document the experimental conditions and provide an initial analysis of select test conditions.

PLIF↗
NASA NTRS2023

Experimental Investigation of Block-TPS Fence/Gap Roughness Effects on Transition Onset and Turbulent Heating at Mach 6

An experimental investigation of boundary-layer transition and convective surface heating on wind tunnel models that simulated aeroshells comprised of multiple blocks of thermal protection system (TPS) material has been performed. Two representative entry vehicle geometries, a sphere-cone aeroshell and a sphere-cone aeroshell, were considered. Multiple cast ceramic models of each geometry were fabricated with varying fence heights or gap depths to represent gap fillers that either protrude above, or are recessed below, the TPS blocks due to differential ablation during reentry. Wind tunnel testing was performed at Mach 6 over a range of Reynolds numbers sufficient to produce laminar, transitional, and turbulent flow. Convective surface heating and boundary-layer transition onset data were obtained using global phosphor thermography. The experimental heating data are presented herein, as are comparisons to laminar and turbulent smooth-wall heat transfer distributions from computational flow field simulations.

Aerothermodynamics↗
NASA NTRS2023

Experimental Investigation of Distributed Sand-Grain Roughness Effects on Transition Onset and Turbulent Heating at Mach 6

An experimental investigation of distributed sand-grain surface roughness effects on hypersonic boundary-layer transition and turbulent heating has been performed. Two representative entry vehicle geometries, a sphere-cone aeroshell and a spherical-cap aeroshell, were considered. Cast ceramic models of each geometry were fabricated with distributed sand-grain roughness patterns of different heights that simulated an ablated thermal protection system. Wind tunnel testing was performed at Mach 6 over a range of Reynolds numbers sufficient to produce laminar, transitional, and turbulent flow. Aeroheating and boundary-layer transition onset data were obtained using global phosphor thermography. The experimental heating data are presented herein, as are comparisons to laminar and turbulent smooth-wall heat transfer distributions from computational flow field simulations. The boundary-layer transition data were found to correlate with a functional representation developed in prior roughness studies, although the data scatter was greater owing to the height variability of distributed sand-grain roughness.

Brian R Hollis↗
NASA NTRS2020

LAURA Users Manual: 5.6

This users manual provides in-depth information concerning installation and execution of Laura, version 5. Laura is a structured, multiblock, computational aerothermodynamic simulation code. Version 5 represents a major refactoring of the original Fortran 77 Laura code toward a modular structure afforded by Fortran 95. The refactoring improved usability and maintainability by eliminating the requirement for problem-dependent recompilations, providing more intuitive distribution of functionality, and simplifying inter- faces required for multi-physics coupling. As a result, Laura now shares gas-physics modules, MPI modules, and other low-level modules with the Fun3D unstructured-grid code. In addition to internal refactoring, several new features and capabilities have been added, e.g., a GNU-standard installation process, parallel load balancing, automatic trajectory point sequencing, free-energy minimization, and coupled ablation and flow field radiation.

Aerodynamics↗
NASA NTRS2020

Hexcomb Pattern Roughness Effects on Blunt Body Transition and Heating

An experimental investigation of hexcomb pattern surface roughness effects on boundary-layer transition and convective heating has been performed. Two representative entry vehicle geometries, a spherical-cap aeroshell and a sphere-cone aeroshell, were considered. Multiple cast ceramic models of each geometry were fabricated with various roughness pattern densities and depths that simulated an ablated hexcomb-structure thermal protection system. Wind tunnel testing was performed at Mach 6 over a range of Reynolds numbers sufficient to produce laminar, transitional, and turbulent flow. Aeroheating and boundary-layer transition onset data were obtained using global phosphor thermography. The experimental heating data are presented herein, as are comparisons to laminar and turbulent smooth-wall heat transfer distributions from computational flow field simulations. The experimental data were used to develop a unified boundary-layer transition correlation for both sandgrain distributed roughness and hexcomb pattern roughness.

Brian R Hollis↗
NASA NTRS2018

Turbulent Aeroheating Measurements on a 7-deg Half-Angle Sphere-Cone in a High-Enthalpy CO2 Expansion Tunnel

A database of heating and pressure measurements on a 7-deg half-angle cone in a highenthalpy expansion tunnel in CO2 has been generated to support development and validation of computational models to be employed in the design of future Mars missions. Laminar, transitional, and turbulent simulations were performed at the test conditions for comparisons with the data. Close agreement was obtained for both fully-laminar and fully turbulent conditions. For the remaining transitional/turbulent conditions, agreement to within, or slightly more than, the estimated experimental uncertainty was demonstrated. The influence of transition intermittency and transition length models on predicted heating levels was demonstrated, as were differences in turbulent heating predictions generated using various algebraic, one-equation, and two-equation turbulence models. These comparisons provide some measure of confidence in turbulent simulation capabilities; however, because the data were not obtained on a relevant entry vehicle geometry, it is not possible to fully quantify computational uncertainties for the definition of Mars mission aerothermodynamic environments at this time

Brian R Hollis↗
NASA NTRSDate not supplied

Aftbody Aeroheating Wind Tunnel Measurements on a Hypersonic Inflatable Aerodynamic Decelerator

The aftbody aeroheating environment of a Hypersonic Inflatable Aerodynamic Decelerator (HIAD) was investigated in the NASA Langley 31-Inch Mach 10 Air Tunnel. The wind tunnel model geometry was representative of the Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) vehicle. Aeroheating data were obtained for a range of Reynolds numbers and angles-of-attack using global phosphor thermography. Aeroheating data were also obtained using a developmental IR thermography technique for evaluation of data quality.

Elizabeth F Rieken↗
NASA NTRSDate not supplied

Improvements to the LAURA Mesh Adaptation Algorithm

This paper describes recent improvements to the LAURA code that removes the requirementof unbroken body-normal lines when using the automated mesh adaptation algorithm inLAURA responsible for mesh alignment with shock and adjusting near-wall mesh spacing. Fornon-simple geometry, restricting block topologies such that blocks span the domain from thesurface wall boundaries to domain inflow boundary can be difficult or impossible. Removing thisrequirement enables novel block topologies that simplify the meshing workflow for LAURA users.The new adaptation algorithm implementation in LAURA is described and several examples ofthe adaptation are presented to demonstrate the efficacy of the adaptation algorithm.

LAURA↗
NASA NTRSDate not supplied

Mars Sample Return Earth Entry System Woven Roughness Mach 6 Aeroheating Test

The Mars Sample Return Earth Entry System is the first entry vehicle designed for a NASA flagship mission to utilize a woven thermal protection system as well as a 52.5 degree sphere cone forebody geometry. As a result, no heritage aeroheating experimental data set exists to compare with computational predictions. In order to obtain a set of validation data for computational models, an extensive wind tunnel test campaign was funded by the Mars Sample Return Earth Entry System project. The first entry in the test campaign was completed in April of 2023, which was an investigation of turbulent heating augmentation due to woven thermal protection system roughness on the 52.5 degree Mars Sample Return - Earth Entry System vehicle forebody geometry. This test entry produced the first ever experimental aeroheating data on a 52.5 degree sphere-cone geometry as well as the first NASA experimental aeroheating data on a woven surface roughness pattern. Data obtained from this test campaign is being directly leveraged to support the NASA flight program, as experimental results are being utilized to validate the computational models which characterize the aeroheating environment that the vehicle experiences and predict turbulent surface heating levels and margins across the woven surface.

Jonathan S Cheatwood↗
NASA NTRSDate not supplied

FLEET and PLIF Velocimetry Within A Mach 10 Hypersonic Air Flow

Femtosecond laser electronic excitation tagging (FLEET) and planar laser-induced fluorescence (PLIF) velocity measurements utilizing molecular tagging velocity (MTV) methods from three recent test campaigns conducted at the 31-in Mach 10 Air Tunnel at the NASA Langley Research Center are highlighted within. The FLEET measurements reported here include the first direct measurement of freestream velocity at this hypersonic wind tunnel facility. Measurement challenges were exasperated by the low gas density of the Mach 10 air freestream (~0.4% of standard temperature and pressure conditions) and even lower gas densities within the hypersonic wake of a 70-degree sphere-cone model. In addition, the hypersonic freestream and very low speed velocities in the wake also tested the measurement dynamic range. To complement the FLEET measurements in the wake of the sphere-cone model, PLIF velocimetry using seeded nitric oxide was also performed. While NO-PLIF velocimetry has been performed at this facility several times by previous researchers, the use of a 1D diffractive optical element for NO-PLIF velocimetry is reported here for the first time. The 1D DOE enabled the generation of up to 75 laser lines simultaneously and improved the spatial extent of the measurement three times compared to previous work. This enabled a wide velocity measurement plane of approximately 130 mm x 130 mm. The velocimetry methods demonstrated here are expected to improve wind tunnel characterization, provide critical data to validate CFD codes, and improve the design of flight vehicles for planetary entry.

FLEET↗
NASA NTRSDate not supplied

Aerodynamic Performance of the Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) Technology Demonstration Mission

The Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) mission successfully demonstrated the deployment and entry performance of a 6 m diameter Hypersonic Inflatable Decelerator on November 10, 2022. This was the largest blunt body flown to date and demonstrated this inflatable aeroshell technology at scale and conditions relevant to Earth and Mars Entry, Descent, and Landing applications. LOFTID built upon the prior successes of the suborbital IRVE and IRVE-3 missions, leveraging and expanding on the flight experience from these and other planetary and Earth sample return missions. Both the re-entry vehicle and ejectable data module were successfully recovered from the Pacific Ocean, with LOFTID satisfying requirements for decelerator performance and stable flight from orbital entry conditions through parachute deployment and splashdown. This work discusses the pre-flight aerodynamics database and reconstructed flight performance of the LOFTID re-entry vehicle.

LOFTID↗
NASA NTRSDate not supplied

Aerodynamic Performance of the Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) Technology Demonstration Mission

The Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) mission successfully demonstrated the deployment and entry performance of a 6 m diameter Hypersonic Inflatable Decelerator on November 10, 2022. This was the largest blunt body flown to date and demonstrated this inflatable aeroshell technology at scale and conditions relevant to Earth and Mars Entry, Descent, and Landing applications. LOFTID built upon the prior successes of the suborbital IRVE and IRVE-3 missions, leveraging and expanding on the flight experience from these and other planetary and Earth sample return missions. Both the re-entry vehicle and ejectable data module were successfully recovered from the Pacific Ocean, with LOFTID satisfying requirements for decelerator performance and stable flight from orbital entry conditions through parachute deployment and splashdown. This work discusses the pre-flight aerodynamics database and reconstructed flight performance of the LOFTID re-entry vehicle.

LOFTID↗
NASA NTRSDate not supplied

FLEET and PLIF Velocimetry Within A Mach 10 Hypersonic Air Flow

Femtosecond laser electronic excitation tagging (FLEET) and planar laser-induced fluorescence (PLIF) velocity measurements utilizing molecular tagging velocity (MTV) methods from three recent test campaigns conducted at the 31-in Mach 10 Air Tunnel at the NASA Langley Research Center are highlighted within. The FLEET measurements reported here include the first direct measurement of freestream velocity at this hypersonic wind tunnel facility. Measurement challenges were exasperated by the low gas density of the Mach 10 air freestream (~0.4% of standard temperature and pressure conditions) and even lower gas densities within the hypersonic wake of a 70-degree sphere-cone model. In addition, the hypersonic freestream and very low speed velocities in the wake also tested the measurement dynamic range. To complement the FLEET measurements in the wake of the sphere-cone model, PLIF velocimetry using seeded nitric oxide was also performed. While NO-PLIF velocimetry has been performed at this facility several times by previous researchers, the use of a 1D diffractive optical element for NO-PLIF velocimetry is reported here for the first time. The 1D DOE enabled the generation of up to 75 laser lines simultaneously and improved the spatial extent of the measurement three times compared to previous work. This enabled a wide velocity measurement plane of approximately 130 mm x 130 mm. The velocimetry methods demonstrated here are expected to improve wind tunnel characterization, provide critical data to validate CFD codes, and improve the design of flight vehicles for planetary entry.

FLEET↗
NASA NTRSDate not supplied

NASA LaRC Hypersonic Experimental Aerothermodynamic Capabilities and Recent Contributions

A review is presented of recent research, development, testing and evaluation aerothermodynamic activities that have been conducted at the NASA Langley Research Center in the Langley Aerothermodynamics Laboratory. An overview of the test facilities, model development and fabrication capabilities, and instrumentation and measurement techniques employed in this work is provided. Contributions to hypersonic flight and planetary exploration programs are detailed, as are fundamental research and development activities. Wind tunnel investigations are described that supported flight programs for NASA and Commercial Crew external partners. Collaborations between NASA projects and academia are also highlighted in this overview of recent wind tunnel experiments.

hypersonic↗
NASA NTRSDate not supplied

NASA Langley Hypersonic Experimental Aerothermodynamic Capabilities and Recent Contributions

A review is presented of recent research, development, testing and evaluation aerothermodynamic activities that have been conducted at the NASA Langley Research Center in the Langley Aerothermodynamics Laboratory. An overview of the test facilities, model development and fabrication capabilities, and instrumentation and measurement techniques employed in this work is provided. Contributions to hypersonic flight and planetary exploration programs are detailed, as are fundamental research and development activities. Wind tunnel investigations are described that supported flight programs for NASA and Commercial Crew external partners. Collaborations between NASA projects and academia are also highlighted in this overview of recent wind tunnel experiments.

hypersonic↗