Search NASA⌕ Search

Engineering topics

Bricker, R. W.

Publications and source records attributed to Bricker, R. W..

17 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Test results from a comparative evaluation of a condensation nuclei fire detector

The fire/smoke alarm response of a condensation nuclei fire detector (CNFD) was compared with photoelectric and ionization detectors. Tests were conducted in a former control room 8.5 m by 8.9 with a 2.7 m ceiling. The room had air supplied from above the ceiling and under the floor with return air exiting from ceiling grills. The environment was varied from 278 to 305 K and relative humidities from 8 to 65%. Four detection zones were located in the room. Each zone contained a sampling head for the CNDF, a photodetector, and an ionization detector so that each detector system had four opportunities to alarm during tests. The particle level in the test room was also monitored during tests with a condensation nuclei particle counter. The CNFD responded to 90% of exposures to smoldering plastic and 84% of exposures to visible fire. The photoelectric response was 43 and 12.5% respectively for the same conditions. The ionization response was 9 and 48 respectively.

Bricker, R. W.↗
NASA NTRS1982

Full-scale flammability test data for validation of aircraft fire mathematical models

Twenty-five large scale aircraft flammability tests were conducted in a Boeing 737 fuselage at the NASA Johnson Space Center (JSC). The objective of this test program was to provide a data base on the propagation of large scale aircraft fires to support the validation of aircraft fire mathematical models. Variables in the test program included cabin volume, amount of fuel, fuel pan area, fire location, airflow rate, and cabin materials. A number of tests were conducted with jet A-1 fuel only, while others were conducted with various Boeing 747 type cabin materials. These included urethane foam seats, passenger service units, stowage bins, and wall and ceiling panels. Two tests were also included using special urethane foam and polyimide foam seats. Tests were conducted with each cabin material individually, with various combinations of these materials, and finally, with all materials in the cabin. The data include information obtained from approximately 160 locations inside the fuselage.

Kuminecz, J. F.↗
NASA NTRS1981

The information systems heritage

This paper addresses key developments in the evolution of information systems over the past five decades. Major areas covered include the growth of imaging sensors from such pioneering devices as the iconoscope and orthicon which ushered in television, through a wide range of vidicon tubes, to the solid-state arrays which characterize current systems; the phenomenal expansion of electronic communications from telegraph and telephone wires, through the introduction of broadcast and microwave relay services, to the present era of worldwide satellite communications and data networks; and the key role of digital computers from their ancient precursors like the abacus and the mechanical calculating engines, through the appearance of the first large-scale electronic computers and their transistorized successors, to the rapid proliferation of miniaturized processors which impact every aspect of aerospace systems today.

Kurzhals, P. R.↗
NASA NTRS1979

Airport flammability, full scale fire tests

The primary objectives of the fire tests are: (1) conduct full scale test with 737 fuselages by the end of 1980; (2) demonstrate evacuation time increase to five minutes minimum; (3) show that exterior fire will not penetrate an intact cabin for five minutes; (4) show that closed cabin will not have excess smoke or temperatures above 400 F; and (5) demonstrate that fire in cabin opening will not propagate throughout cabin. The test program has three phases. A test schedule and status of required materials are presented.

Bricker, R. W.↗
NASA NTRS1979

Seat test program

The test program has the objectives to: (1) evaluate severity of newspaper ignition source with contemporary seats (determine weight loss, visual damage, and if ignition source is severe enough to show improvement with new material configurations); (2) compare damage with jet A-1 ignition source; and (3) determine if materials for seat tests pass FAR 25 and obtain L01. Test configurations, data acquired, material test results, seat test results, and conclusions are presented.

Bricker, R. W.↗
NASA NTRS1978

The 737 aircraft flammability testing

The FAA requested approximately 20 component and full-scale tests in a 737 fuselage to provide validation data or indicate changes that need to be made to a fire math model (Dayton Aircraft Cabin Fire Model) developed for the FAA. Some preliminary tests were conducted to evaluate the adequacy of planned instrumentation. The objectives of the program were met in that it was verified that propagation of a fire could be determined from the sequential response of thermocouples located on a test specimen(such as a seat), and continuous weighing of the specimen during the test was accomplished. Two differenct techniques for measuring smoke density were found to be comparable.

Bricker, R. W.↗
NASA NTRS1976

Full-scale aircraft cabin flammability tests of improved fire-resistant materials, test series 2

Full-scale aircraft flammability tests in which the effectiveness of new fire-resistant materials was evaluated by comparing their burning characteristics with those of other fire-resistant aircraft materials were described. New-fire-resistant materials that are more economical and better suited for aircraft use than the previously tested fire-resistant materials were tested. The fuel ignition source for one test was JP-4; a smokeless fuel was used for the other test. Test objectives, methods, materials, and results are presented and discussed. The results indicate that, similar to the fire-resistant materials tested previously, the new materials decompose rather than ignite and do not support fire propagation. Furthermore, the new materials did not produce a flash fire.

Stuckey, R. N.↗
NASA NTRS1976

Materials research for aircraft fire safety

The thermochemical and flammability characteristics of two polymeric composites currently in use and seven others being considered for use as aircraft interior panels are described. The properties studied included: (1) limiting oxygen index of the composite constituents; (2) fire containment capability of the composite; (3) smoke evolution from the composite; (4) thermogravimetric analysis; (5) composition of the volatile products of thermal degradation; and (6) relative toxicity of the volatile products of pyrolysis. The performance of high-temperature laminating resins such as bismaleimides is compared with the performance of phenolics and epoxies. The relationship of increased fire safety with the use of polymers with high anaerobic char yield is shown. Processing parameters of the state-of-the-art and the advanced bismaleimide composites are detailed.

Kourtides, D. A.↗
NASA NTRS1975

Aircraft seat cushion materials tests

Five component level flammability tests were conducted in a 400 cubic foot chamber to determine the products of combustion and relative destruction of coated (with fire-retardants) and uncoated polyurethane foams during exposure of the foams to a large flaming ignition source for five minutes. The test results indicate that the improved state-of-the-art polyurethane foams without the added fire retardant and coating treatments were not significantly better than untreated older less fire-resistant polyurethane foams. however, by treating and coating the state-of-the-art foams, the production of toxic gases was delayed and the destruction of the foam limited.

Bricker, R. W.↗
NASA NTRS1975

Fire-resistant aircraft materials development and evaluation program

An aircraft flammability program was undertaken to utilize spacecraft developed fire-resistant materials to improve passenger safety and decrease losses from unattended fires in commercial aircraft. Five full-scale aircraft flammability tests were performed to evaluate the effectiveness of improved fire-resistant materials by comparing their burning characteristics with those of pre-1968 aircraft materials.

Bricker, R. W.↗
NASA NTRS1974

Fire-resistant aircraft materials development and evaluation program

The overall objectives of this program are to provide a more fire-resistant commercial aircraft interior and to improve the fuselage insulation barrier between the cabin interior and an exterior fuel fire. Significant secondary objectives are to reduce the smoke and toxic gas production of the materials and to meet the end item use requirements pertaining to wearability, color fastness, and aesthetic appeal. It is shown that the fuselage insulation materials must meet stringent requirements pertaining to acoustic attenuation, low density, and water repellency.

Bricker, R. W.↗
NASA NTRS1972

Apollo experience reports: Window contamination

The problem of window contamination in the Apollo command module is reviewed. All five command module windows were contaminated while in earth orbit on the first three manned Apollo flights. The contamination sources were identified and eliminated. Preflight testing of lunar module windows showed that no serious contamination should occur, and this conclusion was verified in subsequent manned flights. The command module window designs and materials are described, the window contamination sources are identified, and the inflight and chemical analyses of the contamination are outlined. The corrective actions that were taken are reviewed. For the lunar module, the window design and materials and the preflight and fight evaluations are described. Window design recommendations are made.

Leger, L. J.↗
NASA NTRS1971

Flammability testing conducted in support of Apollo 13

In support of the Apollo 13 investigation of the oxygen tank failure, flame propagation rates were determined for Teflon insulation in cryogenic and ambient temperature oxygen for upward, downward, and zero g burns. The propagation rates depended heavily on configuration and varied from 4.8 to 10.9 cm/sec for upward one g burns to 0.48 cm/sec for zero g burns. In addition to the flame propagation rates, tests were conducted to determine if Teflon burning in cryogenic oxygen could ignite metals (promoted ignition) with which it came in contact. Tests conducted on various metal alloys used in the oxygen tank indicated that most of the alloys could be ignited by burning Teflon in certain configurations. After the propagation rates and promoted metal ignitions had been evaluated, a test was conducted on a quantity gauge and wire harness used in the oxygen tank to determine if flame propagation to the tank wall was possible. Propagation of the wire bundle after ignition resulted in a catastrophic failure of the test vessel in the area of the quantity gauge.

Leger, L. J.↗
NASA NTRS1971

Flammability tests for Apollo command module and lunar module mockup

The flammability test program for Apollo command module and lunar module mockups is described. The fire safety design of the modules was verified by performing deliberate ignitions at many locations while the interior atmosphere was controlled to simulate realistic flight conditions. The data obtained for each test and restrictions on various materials are discussed.

Bricker, R. W.↗