Environmentally-assisted cracking of electropolished 316L stainless steel in molten FLiNaK salt
Not provided.
Materials Science↗
Engineering topics
Briggs, Samuel
Publications and source records attributed to Briggs, Samuel.
Deposition-controlled phase separation in CuNb metallic alloys
Vapor co-deposited metal nanocomposites with immiscible components have shown to have several superior properties including mechanical performance, radiation tolerance, and enhanced functionalities. The morphology and structural design of these nanocomposites are important in determining the expression of these properties. The conditions used to deposit thin film nanocomposites are the governing factors in determining the final nanostructure. In this work, we link the effects of process gas pressure, substrate temperature, and sputtering target power on resultant Cu/Nb thin film nanostructures. Here, we find that for films with equiatomic phase fractions of Cu and Nb, inhomogeneous precipitate segregation dominated the structure at lower substrate temperature depositions while higher temperatures distributed the Cu and Nb phases more uniformly. Increasing process gas pressure during deposition lead to a spatially homogeneous, nanocrystalline structure of Cu/Nb. In situ annealing of this sample shows that the phase separated morphology of the two immiscible materials depends on the initial composition. Finally, compositions of Cu and Nb that were highly disparate lead to interface segregation of the minority phase. The morphological evolution observed in the Cu/Nb system is compatible with modified structural zone models for immiscible thin film systems.
36 MATERIALS SCIENCE↗
Design and demonstration of a laboratory-scale oxygen controlled liquid sodium facility
Not Available
Mangus, Dustin↗
Ion irradiation effects on Cr-coated zircaloy-4 surface wettability and pool boiling critical heat flux.
The concept of coating the currently used nuclear fuel cladding (zirconium-based alloy, typically Zircaloy-4 or Zirc-4) with an oxidation preventive layer is a progressing Accident tolerant Fuel (ATF) candidate alloys. The coated Zirc-4-based alloys could be a solution to suppress undesirable fast reaction kinetics with high-temperature steam. Zirc-4 has been the most preferred cladding material in pressurized water reactors (PWRs). Chromium (Cr) based alloys as a coating material provides excellent corrosion protection and good strength and wear resistance. In this paper, we present the surface wettability measurements and pool boiling Critical Heat Flux (CHF) for Cr-coated Zirc-4 claddings pre- and post-exposure to an ion irradiation environment. The wettability measurements, including static contact angle (contact angle, θ) and average surface roughness (surface roughness, Ra), are introduced for samples of different coating thicknesses (5–30 μm thick). The coatings fabricated by the cold spray of Cr-Al particles to 10 mm × 10 mm × 1.95 mm Zirc-4 substrates. Post fabrication, a Pilgering (cold rolling) process, was applied to finalize the coating thickness and resulted in a significant reduction in surface roughness of initially fabricated rough surfaces. The process produced three distinguished samples 5-μm unpolished (as machined), 5-μm, and 30-μm polished (cold rolled). The measurements are presented for the three surfaces and bare Zirc-4 as a baseline surface. The contact angle analyses were implemented in theoretical models from the literature to predict pool boiling CHF. Pool boiling experiments were conducted to measure the pool boiling CHF values and compare them to the predicted values. Scanning Electron Microscope (SEM) images and Energy Dispersive X-ray Spectroscopy (EDS) analysis was performed to characterize the surfaces for better understanding and interpreting the results. The SEM images showed localized surface damage due to ion irradiation. No recognized change in the measured surface roughness due to ion irradiation. The contact angles of irradiated Cr-coated surfaces are consistently higher (10°) than pre-irradiated surfaces. Decreasing the Cr-coating layer thickness resulted in lower contact angle pre- and post- ion irradiation. The predicted pool boiling CHF using the Kandlikar model is in good agreement with the experimentally measured CHF values within ±12% for all samples.
36 MATERIALS SCIENCE↗