Search NASA⌕ Search

Engineering topics

Brissenden, Roy F.

Publications and source records attributed to Brissenden, Roy F..

4 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1961

Analytical and Preliminary Simulation Study of a Pilot's Ability to Control the Terminal Phase of a Rendezvous with Simple Optical Devices and a Timer

One method of controlling the terminal phase of a space rendezvous between two vehicles is first to correct the flight path of the controlled vehicle so that a constant line of sight is established between the vehicles. This correction is accomplished by thrusting normal to the sight line in a direction to arrest the angular motion of this line. Once this collision course has been established, the second step is to control the closure rate for a safe approach along the line of sight. Adequate control of this maneuver requires range and closure-rate information. A combined analytical and preliminary simulation study was conducted to determine the ability of a human pilot to control the rendezvous by this method using visual sightings made during the initial collision-course control to obtain the range and closure rate. The analytical phase of the study reviewed the geometric relations between the vehicles and formed the basis for techniques to transform the angular sightings into range and closure rate. A preliminary simulation was then made to investigate the accuracy of these techniques. The simulation consisted of an analog computer, an oscilloscope to represent the view a pilot would have-with a stabilized sight, and a timer. Results indicate that pilots, using an optical sight and a timer, can successfully arrest the angular motion of the line of sight between two rendezvous vehicles and obtain relative range and closure rate with sufficient accuracy to perform the final braking maneuver successfully.

Lineberry, Edgar C., Jr.↗
NASA NTRS1961

Analog Simulation of a Pilot-Controlled Rendezvous

The rendezvous of a pilot-controlled space ferry vehicle with an orbiting space station was simulated in six degrees of freedom. A fixed-base simulator and an analog computer were used. The ferry vehicle was assumed to have a single main thrusting rocket and to be provided with attitude control. Control of the thrust was provided by a rocket throttle quadrant which could provide either proportional or on-off control. The attitude of the vehicle was controlled during the rendezvous with a two-axis, pencil-type side-arm controller and rudder pedals. For the most part rendezvous maneuvers were made with the target satellite in a circular orbit. In addition, an elliptical station orbit was investigated. Tolerable initial conditions, as well as adequate data presentations, were determined. Results of the investigation indicate that a human pilot can rendezvous successfully with the vehicle and instrumentation considered over a wide band of initial conditions. Coplanar conditions are not necessary. Retro-rocket fuel used is not greatly increased by imposing perturbing influences such as rocket-misalignment torques on the rendezvous vehicle. When excessive attitude-control torques are required to maintain the necessary trim attitudes under misalignment influences, the reaction fuel used for this control increases. The time required for a specific rendezvous varies somewhat between pilots. If control of the time for completing the rendezvous is desired, requirements for retrorocket fuel are affected, and an energy-management schedule is required. Continuous variation of the thrust is not necessary. The pilot positions the throttle to obtain a desired level of thrust, and applies bursts of thrust as required. All data were presented on dialed instruments. The quantities required are range and range rate and line-of-sight rates between the vehicle and the station, vehicle attitudes and angular rates, and the angles subtended by the line of sight. For the equipment assumed herein, satellite rendezvous presented no great problem to the pilot.

Brissenden, Roy F.↗
NASA NTRS1960

Satellite Attitude Control Using a Combination of Inertia Wheels and a Bar Magnet

The use of inertia wheels to control the attitude of a satellite has currently aroused much interest. The stability of such a system has been studied in this investigation. A single-degree-of-freedom analysis indicates that a response with suitable dynamic characteristics and precise control can be achieved by commanding the angular velocity of the inertia wheel with an error signal that is the sum of the attitude error, the attitude rate, and the integral of the attitude error. A digital computer was used to study the three-degree-of-freedom response to step displacements, and the results indicate that the cross-coupling effects of inertia coupling and precession coupling had no effect on system stability. A study was also made of the use of a bar magnet to supplement the inertia wheels by providing a means of removing any momentum introduced into the system by disturbances such as aerodynamic torques. A study of a case with large aerodynamic torques, with a typical orbit, indicated that the magnet was a suitable device for supplying the essential trimming force. Single-degree-of-freedom bench tests generally verified the dynamic response predicted by the analytical study. the test table to within plus or minus 9 arc-seconds of the reference direction, even though the hardware components that were used in these tests were not specifically designed for the control system.

Adams, James J.↗