Engineering topics

Brooks, George W.

Publications and source records attributed to Brooks, George W..

6 records

NASA NTRS1985

The results of a limited study of approaches to the design, fabrication, and testing of a dynamic model of the NASA IOC space station. Executive summary

The options for the design, construction, and testing of a dynamic model of the space station were evaluated. Since the definition of the space station structure is still evolving, the Initial Operating Capacity (IOC) reference configuration was used as the general guideline. The results of the studies treat: general considerations of the need for and use of a dynamic model; factors which deal with the model design and construction; and a proposed system for supporting the dynamic model in the planned Large Spacecraft Laboratory.

Brooks, George W.↗

NASA NTRS1960

An Analysis of the Flapwise Bending Frequencies and Mode Shapes of Rotor Blades Having Two Flapping Hinges to Reduce Vibration Levels

This paper presents the analysis of the flapwise natural bending frequencies and mode shapes of rotor blades with two flapping hinges located at arbitrary blade radii. The equations of motion are derived for a blade of variable mass and stiffness distribution. Solutions to the equations (natural frequencies and mode shapes) are presented for a typical blade of constant cross section having a wide range of hinge locations. The results show that the natural frequencies of the blades can be changed appreciably by varying the locations of the blade hinges, and that with two properly located flapping hinges, blade designs are possible which eliminate or greatly reduce conditions of resonance between the blade natural frequencies and the frequencies of the harmonic air loads. The results also show that ratios of natural frequency to rotor speed below a value of 6.0 are essentially constant for variations in rotor speed consistent with helicopter and VTOL applications.

Brooks, George W.↗

NASA NTRS1960

Structural Considerations of Inflatable Reentry Vehicles

The state of the design art for inflated structures applicable to reentry vehicles is discussed. Included are material properties, calculations of buckling and collapse loads, and calculations of deflections and vibration frequencies. A new theory for the analysis of inflated plates is presented and compared with experiment.

Leonard, Robert W.↗

NASA NTRS1959

A Dynamic Model Investigation of the Effect of a Sharp-Edge Vertical Gust on Blade Periodic Flapping Angles and Bending Moments of a Two-Blade Rotor

A two-blade rotor having a diameter of 4 feet and a solidity of 0.037 was subjected to sharp-edge vertical gusts while being operated at various forward speeds to study the effect of the gusts on the blade periodic bending moments and flapping angles. Variables studied included gust velocity, collective pitch angle, flapping hinge offset, and tip-speed ratio. Dimensionless coefficients are derived for the periodic components of the incremental changes in blade flapping angles and bending moments which arise when a rotor blade penetrates a sharp-edge gust. Mental changes in both the flapping angles and bending moments are essentially proportional to gust velocity, and the coefficients express the ratio of these increments to gust velccity. The results show that the flapping coefficient usually increases with an increase in collective pitch angle, is generally dependent on tip-speed ratio, and is essentially independent of the amount of flapping hinge offset. The bending-moment coefficient is also dependent on collective pitch angle and tip-speed ratio. Expected reductions in bending moments are realized by the use of flapping hinges, and further reductions in bending moments are achieved as the amount of flapping hinge offset is increased. Comparison of the experimental results of this investigation with limited available theoretical results shows substantial agreement but indicates that the assumption that the response of the rotor to a sharp-edge gust is independent of the collective pitch angle prior to gust entry is probably inadequate.

McCarty, John Locke↗

NASA NTRS1959

Wind-Tunnel Investigation of the Effect of Angle of Attack and Flapping-Hinge Offset on Periodic Bending Moments and Flapping of a Small Rotor

A two-blade rotor having a diameter of 4 feet and a solidity of 0.037 was tested in the Langley 300-MPH 7- by 10-foot tunnel to obtain information on the effect of certain rotor variables on the blade periodic bending moments and flapping angles during the various stages of transformation between the helicopter and autogiro configuration. Variables studied included collective pitch angle, flapping-hinge offset, rotor angle of attack, and tip-speed ratio. The results show that the blade periodic bending moments generally increase with tip-speed ratio up into the transition region, diminish over a certain range of tip-speed ratio, and increase again at higher tip-speed ratios. Above the transition region, the bending moments increase with collective pitch angle and rotor angle of attack. The absence of a flapping hinge results in a significant amplification of the periodic bending moments, the magnitudes of which increase with tip-speed ratio. When the flapping hinge is used, an increase in flapping-hinge offset results in reduced period bending moments. The aforementioned trends exhibited by the bending moments for changes in the variables are essentially duplicated by the periodic flapping motions. The existence of substantial amounts of blade stall increased both the periodic bending moments and the flapping angles. Harmonic analysis of the bending moments shows significant contributions of the higher harmonics, particularly in the transition region.

McCarty, John Locke↗

NASA NTRS1958

Analytical and Experimental Determination of the Coupled Natural Frequencies and Mode Shapes of a Dynamic Model of a Single-Rotor Helicopter

A combined analytical and experimental determination is made of the coupled natural frequencies and mode shapes in the longitudinal plane of symmetry for a dynamic model of a single-rotor helicopter. The analytical phase is worked out on the basis of a seven-degree-of-freedom system combining elastic deflections of the rotor blades, rotor shaft, pylon, and fuselage. The calculated coupled frequencies are first compared with calculated uncoupled frequencies to show the general effects of coupling and then with measured coupled frequencies to determine the extent to which the coupled frequencies can be calculated. The coupled mode shapes are also calculated and were observed visually with stroboscopic lights during the tests. A comparison of the coupled and uncoupled natural frequencies shows that significant differences exist between these frequencies for some of the modes. Good agreement is obtained between the measured and calculated values for the coupled natural frequencies and mode shapes. The results show that the coupled natural frequencies and mode shapes can be determined by the analytical procedure presented herein with sufficient accuracy if the mass and stiffness distributions of the various components of the helicopter are known.

Silveira, Milton A.↗