Search NASA⌕ Search

Engineering topics

Brophy, J. R.

Publications and source records attributed to Brophy, J. R..

53 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Calculation of plasma properties in ion sources

Simple algebraic equations are developed that can be used to calculate the average primary electron density, the average primary to Maxwellian density ratio, and the average Maxwellian electron temperature in the discharge chamber of a cusped magnetic field ion source. These properties may be calculated as functions of the propellant gas flow rate and the propellant utilization efficiency. Each of the plasma properties calculated using the model agrees well with the corresponding experimental data for both argon and xenon gases over a wide range of propellant flow rates and utilization efficiencies.

Brophy, J. R.↗
NASA NTRS1985

Investigation of arcjet nozzle performance

An investigation is performed to examine the feasibility of improving arcjet performance through the use of contoured nozzle designs. The results of preliminary experiments performed on two different nozzle configurations, a 19 degree half-angle cone and a 'bell' shaped nozzle, are described. A unique experimental arcjet apparatus, which effectively tests only the change in nozzle contour on arcjet performance is used in this investigation. The preliminary experimental results indicate approximately an 8 percent improvement in thrust and specific impulse for operation at 15 kW with an ammonia flow rate of 0.20 g/s for a 'bell' shaped nozzle compared to a conical nozzle.

Brophy, J. R.↗
NASA NTRS1985

Development and life-testing of 10 kW class thermal arcjet engines

A facility to develop and test thermal arcjet engines over extended periods of time has been constructed and is described in this paper. It consists of a large vacuum tank, high capacity vacuum pumps, a 100 kW power supply and a large ammonia propellant storage and delivery system. The facility is instrumented to measure electrical power dissipated in the engine, propellant mass flow rate and developed thrust. Pressures and temperatures up to 2400 K can also be measured. The entire facility is computer-controlled and can be operated unattended for many weeks. Two 30 kW thermal arcjet engines that have been designed, built and are being tested in this facility are also described.

Pivirotto, T. J.↗
NASA NTRS1984

Ion thruster performance model

A model of ion thruster performance is developed for high flux density, cusped magnetic field thruster designs. This model is formulated in terms of the average energy required to produce an ion in the discharge chamber plasma and the fraction of these ions that are extracted to form the beam. The direct loss of high energy (primary) electrons from the plasma to the anode is shown to have a major effect on thruster performance. The model provides simple algebraic equations enabling one to calculate the beam ion energy cost, the average discharge chamber plasma ion energy cost, the primary electron density, the primary-to-Maxwellian electron density ratio and the Maxwellian electron temperature. Experiments indicate that the model correctly predicts the variation in plasma ion energy cost for changes in propellant gas (Ar, Kr and Xe), grid transparency to neutral atoms, beam extraction area, discharge voltage, and discharge chamber wall temperature. The model and experiments indicate that thruster performance may be described in terms of only four thruster configuration dependent parameters and two operating parameters. The model also suggests that improved performance should be exhibited by thruster designs which extract a large fraction of the ions produced in the discharge chamber, which have good primary electron and neutral atom containment and which operate at high propellant flow rates.

Brophy, J. R.↗
NASA NTRS1984

The effect of discharge chamber wall temperature on ion thruster performance

Experiments conducted on a ring cusp ion thruster that could be maintained at temperatures in the range 80 K to 500 K during operation by cooling it with liquid nitrogen are described. The measured changes in performance induced by discharge chamber wall temperature changes are compared to those predicted by a simple discharge chamber model. Good agreement between the temperature induced effects predicted by the model and measured results are demonstrated. Decreases in wall temperature to about 90 K are shown to effect substantial improvements in performance.

Wilbur, P. J.↗
NASA NTRS1984

Simple performance model for ring and line cusp ion thrusters

A model is developed for high magnetic field strength cusped thrusters which results in a single equation describing the thruster performance. Such a simple result is made possible by formulating the model in terms of the average energy expended in producing ions in the discharge plasma and the fraction of these ions that are extracted into the beam. A key feature of the model is that it allows one to calculate the average plasma ion energy cost as a function of the propellant utilization knowing only thruster geometric design parameters and the propellant gas. The model is exercised to indicate the effects on performance resulting from changes in the extracted ion fraction, the quality of the containment of primary electrons, the propellant mass flow rate, the propellant gas and the transparency of the accelerator system to neutral atoms.

Brophy, J. R.↗
NASA NTRS1984

An experimental investigation of cusped magnetic field discharge chambers

Several features of a proposed model of ion thruster performance are tested experimentally. The experiment conducted demonstrates the effects of variation in thruster operating parameters on the average plasma ion energy costs and extracted ion fractions of various ring and line cusp discharge chambers. The results indicate that the model correctly predicts the variation in the plasma ion energy cost resulting from changes in: propellant gas, grid transparency to neutral atoms, beam extraction area, and discharge voltage. In addition, the model is shown to be applicable to both ring and line cusp designs. Measurements of the extracted ion fraction indicate that this parameter tends to increase with decreasing discharge voltage and is generally higher for operation with argon as opposed to krypton propellant. Results suggest that to use the proposed thruster performance model as an aid in thruster design the performance may be described in terms of four thruster configuration dependent constants and two operating parameters.

Brophy, J. R.↗
NASA NTRS1982

J series thruster isolator failure analysis

Three Hg propellant isolators (two cathode and one main) failed during testing in the Mission Profile Life Test. These failures involved contamination of the surface of the alumina insulating body which resulted in heating of the vaporizer by leakage current from the high voltage supply, with subsequent loss of propellant flow rate control. Failure analysis of the isolators showed the surface resistance was temperature dependent and that the alumina could be restored to its original insulating state by grit blasting the surface. The contaminant was identified as carbon and the most likely sources identified as ambient facility hydrocarbons, directed back-sputtered facility materials, and outgassing from organic insulating materials within the thruster envelope. Methods to eliminate contamination from each of these sources are described.

Campbell, J. W.↗
NASA NTRS1982

The flexible magnetic field thruster

The thruster is designed so that ion currents to various internal surfaces can be measured directly; these measurements facilitate calculations of the distribution of ion currents inside the discharge chamber. Experiments are described suggesting that the distribution of ion currents inside the discharge chamber is strongly dependent on the shape and strength of the magnetic field but independent of the discharge current, discharge voltage, and neutral flow rate. Measurements of the energy cost per plasma ion suggest that this cost decreases with increasing magnetic field strength as a consequence of increased anode shielding from the primary electrons. Energy costs per argon plasma ion as low as 50 eV are measured. The energy cost per beam ion is found to be a function of the energy cost per plasma ion, extracted ion fraction, and discharge voltage. Part of the energy cost per beam ion has to do with creating many ions in the plasma and then extracting only a fraction of them into the beam. The balance of the energy goes into accelerating the remaining plasma ions into the walls of the discharge chamber.

Brophy, J. R.↗
NASA NTRS1981

Design model for the baffle aperture region of a hollow cathode thruster

A current balance on the main discharge chamber of an electron bombardment thruster is carried out. It is shown that the discharge current is the sum of the net cathode emission current, the beam current, and the ion current to cathode potential surfaces. Measurements of ion currents outside the virtual anode surface in a SERT II divergent magnetic field thruster show that relatively few ions cross this surface. This implies that ions are directed preferentially toward the anode and cathode pole pieces. A simple theoretical model useful as an aid in the design of the baffle aperture region of a hollow cathode equipped thruster is developed. The electron diffusion process through the aperture is modeled in accordance with the Bohm diffusion theory. The model is shown to yield consistent results for a given thruster geometry over substantial changes in operating conditions. The model's design usefulness is limited by a factor of two uncertainty observed over different thruster/cathode region geometries and by the accuracy to which the plasma parameters required as inputs to the model can be specified.

Brophy, J. R.↗
NASA NTRS1979

Electron diffusion through the baffle aperture of a hollow cathode thruster

The use of a hollow cathode in place of an oxide cathode to increase thruster operating lifetimes requires, among other things, the addition of a baffle to restrict the flow of electrons from the hollow cathode. A theoretical model is developed which relates the baffle aperture area of a hollow-cathode thruster to the magnetic flux density and plasma properties in the aperture region, with the result that this model could be used as an aid in thruster design. Extensive Langmuir probing is undertaken to verify the validity of the model and demonstrate its capability. It is shown that the model can be used to calculate the aperture area required to effect discharge operation at a specified discharge voltage and arc current.

Brophy, J. R.↗