Experimental and numerical investigation of a shock wave impingement on a cylinder
Explore the source record for details and available documents.
Brosh, A.↗
Engineering topics
Brosh, A.
Publications and source records attributed to Brosh, A..
An experimental investigation of the impingement of a planar shock wave on an axisymmetric body at Mach 3
An experimental study of the flow caused by a planar shock wave impinging obliquely on a cylinder is presented. The complex three dimensional shock wave and boundary layer interaction occurring in practical problems, such as the shock wave impingement from the shuttle nose on an external fuel tank, and store carriage interference on a supersonic tactical aircraft were investigated. A data base for numerical computations of complex flows was also investigated. The experimental techniques included pressure measurements and oil flow patterns on the surface of the cylinder, and shadowgraphs and total and static pressure surveys on the leeward and windward planes of symmetry. The complete data is presented in tabular form. The results reveal a highly complex flow field with two separation zones, regions of high crossflow, and multiple reflected shocks and expansion fans.
Brosh, A.↗
An experimental and numerical investigation of the impingement of an oblique shock wave on a body of revolution
Attention is given to the experimental study and numerical simulation of the impingement of oblique shock wave on a cylinder, in order both to document the complex three-dimensional shock wave and boundary layer interaction occurring in practical problems (such as stores carriage interference in a supersonic tactical aircraft) and to conduct a critical comparison of experimental measurements and numerical computations for such complex flows. A thin layer approximation of the Navier-Stokes equations was solved by means of a mixed explicit-implicit scheme. Experimental measurements reveal a highly complex flow field with two distinct adjacent separation zones, regions of high cross flow, and multiply reflected shocks and expansion fans.
Brosh, A.↗
Conjugated heat transfer in a laminar boundary layer with heat source at the wall
This work presents the solution of the temperature field in a two-dimensional laminar incompressible flow over a conducting solid plate with a line heat source located at the fluid-solid interface perpendicular to the flow direction. A numerical scheme was used to obtain the temperature profiles as a function of the source strength, and of the properties of the fluid and the solid. The heat conduction and forced convection in the fluid and the heat conduction in the solid were solved for the case of moderate temperature rise, where the assumption of constant properties applies. The model enables the improvement of an instrument for the detection of boundary layer separation. It was found that for the actual parameters of the separation detector, a distance of 4 to 24 mm between the sensors gives an indication of 70 percent of the maximum temperature difference.
Brosh, A.↗
Flow separation detector
An arrangement for sensing the fluid separation along a surface which employs a thermally insulating element having a continuous surface blending into and forming a part of the fluid flow surface is described. A sudden decrease in the temperature of the downstream sensor conductor and concomitant increase in the temperature of the upstream sensor conductor is an indication of the separation. When the temperatures are returned to the state achieved during normal flow, the indicator thereby indicates the normal, attached fluid flow. The conductors may be, for example, wires or thin films, and should be within the viscous sub-layer of the expected fluid flow. A single heater and several pairs of sensors and corresponding sensor conductors may be used to detect not only the fluid flow and the separation, but the direction of the fluid flow, over the fluid flow surface.
Mateer, G. C.↗
A normal shock-wave turbulent boundary-layer interaction at transonic speeds
Experimental results, including surveys of the mean and fluctuating flow, and measurements of surface pressure, skin friction, and separation length, are compared with solutions to the Navier-Stokes equations utilizing various algebraic eddy viscosity models to describe the Reynolds shear stresses. The experimental data, obtained at a free-stream Mach number of 1.5 and Reynolds numbers between 10 million and 80 million, show that a separated zone forms near the foot of the shock and that its length is proportional to the initial boundary-layer thickness; that a supersonic region forms downstream of the shock; and that the shear stress increases significantly through the interaction and subsequently decays downstream. The computations adequately represent the qualitative features of the flow field throughout the interaction but quantitatively underpredict the extent of separation and the downstream level of skin friction.
Mateer, G. G.↗
A hot-wire surface gage for skin friction and separation detection measurements
A heated-element, skin-friction gage employing a very low thermal conductivity support is described. It is shown that the effective dimension of the gage in the stream direction in only 0.06 mm, including the effects of heat conduction in the supporting material. Because of its small size, the calibration of the gage is independent of the kind of boundary-layer flow (whether laminar or turbulent) and is insensitive to pressure gradients. Construction tolerances can be maintained so that a single universal calibration can be applied. Multiple gages, sufficiently closely spaced so as to interfere with each other, are shown to provide accurate determinations of the locations of the points of boundary-layer separation and reattachment.
Rubesin, M. W.↗
Flush-mounted hot-wire gage for skin friction and separation detection measurements
A heated-element skin-friction gage employing a very low thermal-conductivity support is described. It is shown that the effective dimension of the gage in the stream direction is only 0.06 mm, including the effects of heat conduction in the supporting material. Because of its small size, the calibration of the gage is independent of the kind of boundary-layer flow (whether laminar or turbulent) and is insensitive to pressure gradients. Construction tolerances can be maintained so that a single universal calibration can be applied. Multiple gages, sufficiently closely spaced so as to interfere with each other, are shown to provide accurate determinations of the location of the points of boundary-layer separation and reattachment.
Rubesin, M. W.↗