Search NASA⌕ Search

Engineering topics

Brown, J. D.

Publications and source records attributed to Brown, J. D..

10 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Overhaul and installation of the ICARUS-T600 liquid argon TPC electronics for the FNAL Short Baseline Neutrino program

The ICARUS T600 liquid argon (LAr) time projection chamber (TPC) underwent a major overhaul at CERN in 2016–2017 to prepare for the operation at FNAL in the Short Baseline Neutrino (SBN) program. This included a major upgrade of the photo-multiplier system and of the TPC wire read-out electronics. The full TPC wire read-out electronics together with the new wire biasing and interconnection scheme are described. The design of a new signal feed-through flange is also a fundamental piece of this overhaul whose major feature is the integration of all electronics components onto the signal flange. Initial functionality tests of the full TPC electronics chain installed in the T600 detector at FNAL are also described.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
NASA NTRS1990

Measurements Of Shock-Separated Turbulent Boundary Layers

Report documents surface and flow-field measurements of two- and three-dimensional, shock-separated, turbulent boundary layers. Data tabulated to facilitate comparison with other measurements and computations. Shows shock-interaction shadowgraph and oil-flow pattern for each angle. Plotted profiles given for pressures, velocities, Reynolds stresses, and turbulent kinetic energies.

Brown, J. D.↗
NASA NTRS1990

A laser Doppler velocimeter approach for near-wall three-dimensional turbulence measurements

A near-wall laser Doppler velocimeter approach is described that relies on a beam-turning probe which makes possible the direct measurement of the crossflow velocity at a grazing incident and the placement of optical components close to the flow region of interest regardless of test facility size. Other important elements of the approach are the use of digital frequency processing, an optically smooth measurement surface, and observation of the sensing volume at 90 degrees. The combination was found to dramatically reduce noise-in-signal effects caused by surface light scattering. Turbulent boundary-layer data to within 20 microns (y(sup+) approximately equal to 1) of the surface are presented which illustrate the potential of the approach.

Johnson, D. A.↗
NASA NTRS1988

A documentation of two- and three-dimensional shock-separated turbulent boundary layers

A shock-related separation of a turbulent boundary layer has been studied and documented. The flow was that of an axisymmetric turbulent boundary layer over a 5.02-cm-diam cylinder that was aligned with the wind tunnel axis. The boundary layer was compressed by a 30 deg half-angle conical flare, with the cone axis inclined at an angle alpha to the cylinder axis. Nominal test conditions were P sub tau equals 1.7 atm and M sub infinity equals 2.85. Measurements were confined to the upper-symmetry, phi equals 0 deg, plane. Data are presented for the cases of alpha equal to 0. 5. and 10 deg and include mean surface pressures, streamwise and normal mean velocities, kinematic turbulent stresses and kinetic energies, as well as reverse-flow intermittencies. All data are given in tabular form; pressures, streamwise velocities, turbulent shear stresses, and kinetic energies are also presented graphically.

Brown, J. D.↗
NASA NTRS1988

Fluctuations and massive separation in three-dimensional shock-wave/boundary-layer interactions

Shock-wave unsteadiness was observed in rapidly compressed supersonic turbulent boundary layer flows with significant separation. A Mach 2.85 shock-wave/turbulent boundary layer flow was set up over a series of cylinder-flare bodies in the High Reynolds Number Channel 1. The transition from fully attached to fully separated flow was studied using axisymmetric flares with increasing compression angles. In the second phase, the 30 deg flare was inclined relative to the cylinder axis, so that the effect on a separated flow of increasing 3 dimensionality could be observed. Two 3-D separated cases are examined. A simple conditional sampling technique is applied to the data to group them according to an associated shock position. Mean velocities and turbulent kinetic energies, computed from the conditionally samples data, are compared to those from the unsorted data and to computed values. Three basic questions were addressed: can conditional sampling be used to provide snapshots of the flow; are averaged turbulence quantities dominated by the bimodal nature of the interaction; and is the shock unsteadiness really important to computational accuracy.

Kussoy, M. I.↗
NASA NTRS1988

Fluctuations and massive separation in three-dimensional shock-wave/boundary-layer interactions

Shock-wave unsteadiness was observed in rapidly compressed supersonic turbulent boundary layer flows with significant separation. A Mach 2.85 shock-wave/turbulent boundary layer flow was set up over a series of cylinder-flare bodies in the High Reynolds Number Channel 1. The transition from fully attached to fully separated flow was studied using axisymmetric flares with increasing compression angles. In the second phase, the 30-deg flare was inclined relative to the cylinder axis, so that the effect on a separated flow of increasing three-dimensionality could be observed. Two 3-D separated cases are examined. A simple conditional sampling technique is applied to the data to group them according to an associated shock position. Mean velocities and turbulent kinetic energies, computed from the conditionally sampled data, are compared to those from the unsorted data and to computed values. Three basic questions were addressed: can conditional sampling be used to provide snapshots of the flow; are averaged turbulence quantities dominated by the bimodal nature of the interaction; and is the shock unsteadiness really important to computational accuracy.

Kussoy, M. I.↗
NASA NTRS1987

Two-component LDV investigation of 3-dimensional shock/turbulent boundary layer interactions

Mean-velocity and turbulence measurements obtained by two-component laser Doppler velocimetry are presented, together with numerical predictions, for the shock-related separation of a turbulent boundary layer at Mach 2.85. The basic geometry, a 30 deg half-angle flare mounted on a long cylinder, is made three-dimensional by tipping the flare at an angle of attack, alpha. The separation length and general upstream influence increase with alpha. A recirculating vortex in the separated zone becomes stronger as three-dimensionality increases. A large-scale unsteadiness of the separation shock wave and surrounding flowfields grows in amplitude with alpha, and appears to strongly influence the amplification of turbulence correlations ahead of detachment. Scaling of the streamwise coordinate by separation length causes two-dimensional and three-dimensional data profiles on the cylinder to collapse for most measured quantities.

Brown, J. D.↗
NASA NTRS1968

Coaxial cable stripper for confined areas

Manual coaxial cable stripper quickly and accurately prepares a coaxial cable in a confined area. With this tool, preparation time is greatly reduced, and a completely inexperienced technician can perform the operation.

Brown, J. D.↗