Search NASA⌕ Search

Engineering topics

Bryan, Chris

Publications and source records attributed to Bryan, Chris.

28 records · Page 2

Mechanical and Microstructural Characterization of Low-Temperature Neutron Irradiated Zircaloy-4

Zr-based alloys, namely Zircaloy-2, Zircaloy-4, ZIRLO, or M5, have been used in light water reactors (LWRs) as structural materials (cladding, pressure tubes, and etc.). Under irradiation conditions, especially at harsh pressurized water reactor (PWR) conditions, these Zr alloys can undergo embrittlement due to corrosion, hydriding, and irradiation induced stresses. This ultimately leads to the severe degradation of Zr-alloys and increase the probability of fuel failure. While various research efforts have been conducted in developing better Zr-based alloys to withstand these harsh environments, there is a considerable amount of Zr-alloy characteristics, such as change in mechanical properties under irradiation conditions and its relationship to the materials microstructure, that need to be studied. This present study has focused on investigation of mechanical and microstructural properties of Zircaloy-4 under low temperature (80 - 100 deg. C) neutron irradiation conditions. Some of the samples studied were also hydrided to evaluate influence of hydride precipitates in the material. (authors)

36 MATERIALS SCIENCE↗

Materials Irradiation Facility (MIF) at the High Flux Isotope Reactor (HFIR)

The Material Irradiation Facility (MIF) at the Oak Ridge National Laboratory (ORNIL) High Flux Isotope Reactor (HIFR) controls and monitors instrumented irradiation experiments for materials and fuel research. In 2013 ORNIL founded a Laboratory Directed Research and Development project to reinvigorate the use of instrumented experiments by redesigning MIF to enhance its capabilities. MIF improvements include an updated and more sophisticated experiment monitoring system, a modular design allowing easier addition of simultaneous experiments, and features that allow rapid incorporation of additional instrumentation Interest in materials and fuel irradiation has increased significantly over the last decade. Much of this interest is related to investigating the performance of advanced materials for fusion environments, designing and developing improved fuel and cladding materials, and examining material characteristics and behavior under irradiation conditions. At ORNL, the irradiation engineering team has more than 60 years of experience designing and fabricating various types of irradiation experiments. Rabbit capsule experiments are small scale and relatively inexpensive. These capsules are typically designed to be irradiated in the flux-trap region of the core. Full-length target capsules are larger scale and could be either instrumented or non-instrumented. These more complicated capsules can be irradiated in any of the experiment facilities at HFIR. Instrumented experiment irradiation provides significant advantages for researchers. The unique advantage is that the researcher can monitor and acquire in situ data and change capsule operating conditions in real time during the irradiation. This capability enables tight control of desired experimental conditions so that they match the design specifications throughout the irradiation. Also, the experiment conditions (e.g., temperature and pressure) can be altered during the test, enabling significant flexibility and the ability to collect considerably more data from a single experimental capsule. This capability allows measurement of a variety of material properties (conductivity, fission product composition, etc.) that otherwise would only be available upon post-irradiation examination, where non-equilibrium conditions brought on by irradiation do not exist. The data generated by these experiments contribute significantly to the understanding of material behavior under irradiation. MIF is an experimental platform that can host fully instrumented and monitored experiments in a high neutron flux environment. Its primary functions are to provide clean inert gas (helium, neon, argon) to experiments at controlled pressures and flows, monitor irradiation conditions (typically temperatures and pressures) during irradiation, and monitor effluent gases from experiments. This facility allows monitoring of chemical processes during a fueled irradiation, where this becomes important for detecting fuel failures. This paper reports the efforts towards reestablishing the value of HFIR for instrumented irradiation experiments and the improvements to MIF that ultimately reduce the costs of instrumented irradiation. This project advances ORNL materials capabilities to new levels by providing a state-of-the art, robust and flexible facility that can be expanded as customer requirements change, while supporting the goals of the fusion, advanced fuels, and structural materials programs. (authors)

42 ENGINEERING↗

Additive Manufacturing of Research Reactor Control Elements and Subsequent Neutron Irradiation

Additive manufacturing techniques have made major strides in recent years and are now capable of creating complex components in near-final form. The nuclear industry has many applications with complicated and even unique components that are time consuming, expensive, and more difficult to make using traditional fabrication routes. Modern fabrication techniques possess the potential to reduce fabrication lead-time and costs while increasing quality and efficiency. However, these methods have not been adopted due to the need for strict validation for nuclear applications. Unlike structural components that largely consist of a uniform material, for nuclear reactor core components incorporation of fissile or neutron poison materials inside a cladding becomes necessary. This in turn requires a more complex and flexible manufacturing method to produce these hybrid components. In this study, demonstration of ultrasonic additive manufacturing (UAM) process to produce components resembling research reactor control elements was carried out]. Specifically, the control elements for ORNL's High Flux Isotope Reactor (HFIR) were targeted. These control elements (consisting of an inner cylinder and four outer plates) are placed on the periphery of the circular HFIR core. The control elements consist of Al6061-T6 alloy with a 13-cm-long grey and a 56-cm-long black region, corresponding to 40 wt% of Ta and 30 wt% Eu{sub 2}O{sub 3} (europia) are incorporated along their length. In this study various fabrication parameters for production of aluminum blocks with and without embedded Eu{sub 2}O{sub 3} and Ta bearing compacts were explored. Select optimized specimens we then irradiated inside HFIR for one reactor cycle. The UAM process exploits ultrasonic energy to facilitate solid-state welding of metal foils in contact under pressure. This additive process is carried out in successive layers to build up the material and when coupled with CNC milling, it yields complex 3D components. The milling and subsequent additive steps may be used to embed foreign material into the material undergoing buildup. In this manner fissile or neutron poison elements may be incorporated into the complex structure, though in an inhomogeneous fashion. Multiple Al-6061 blocks were produced by UAM using 25 mm wide by 0.15 mm thick Al-6061-H18 tapes. The mechanical properties of these blocks in the as-fabricated condition was characterized in detail and it was shown that a great degree of anisotropy in the mechanical behavior exists between the direction in the tape plane and the direction perpendicular to the tapes (buildup direction) The latter exhibited reduced modulus and significantly smaller strength. Post production heat treatment appeared to greatly enhance the strength in the buildup direction. Multiple tensile specimens machined per SS-J3 geometry were prepared for irradiation testing. The tensile specimen matrix was set up to enable post irradiation examination of mechanical properties in various directions as well as after heat treatment. A small block with embedded Ta- and Eu{sub 2}O{sub 3}-bearing compacts, three of each kind, was also produced, as demonstrated previously. These compacts were 5.7 mm in diameter and 1.6 mm in height and contained 60 vol Ta or Eu{sub 2}O{sub 3}. The poison-bearing Al-6061 block alongside the tensile bars was loaded into a perforated rabbit (irradiation capsule) for irradiation in HFTK. The perforated rabbit allows penetration of HFIR water coolant into the Interior of the capsule in direct contact with the test specimens. The rabbit was loaded into the flux trap region at the uppermost position in the core. Irradiation temperature was 68 deg. C and fast neutron (E>0.1 MeV) fluence was 10{sup 25} neutrons/m{sup 2}. Currently PIE activities are ongoing that are focused on mechanical testing of irradiated tensile bars and metallographic examination of neutron poison bearing block.

36 MATERIALS SCIENCE↗

Needs and Requirements for Future Research Reactors (ORNL Perspectives)

The High Flux Isotope Reactor (HFIR) is a vital national and international resource for neutron science research, production of radioisotopes, and materials irradiation. While HFIR is expected to continue operation for the foreseeable future, interest is growing in understanding future research reactors features, needs, and requirements. To clarify, discuss, and compile these needs from the perspective of Oak Ridge National Laboratory (ORNL) research and development (R&D) missions, a workshop, titled “Needs and Requirements for Future Research Reactors”, was held at ORNL on May 12, 2015. The workshop engaged ORNL staff that is directly involved in research using HFIR to collect valuable input on the reactor’s current and future missions. The workshop provided an interactive forum for a fruitful exchange of opinions, and included a mix of short presentations and open discussions. ORNL staff members made 15 technical presentations based on their experience and areas of expertise, and discussed those capabilities of the HFIR and future research reactors that are essential for their current and future R&D needs. The workshop was attended by approximately 60 participants from three ORNL directorates. The agenda is included in Appendix A. This document summarizes the feedback provided by workshop contributors and participants. It also includes information and insights addressing key points that originated from the dialogue started at the workshop. A general overview is provided on the design features and capabilities of high performance research reactors currently in use or under construction worldwide. Recent and ongoing design efforts in the US and internationally are briefly summarized, followed by conclusions and recommendations.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Large-Batch Reduction of Molybdenum Trioxide

Unconverted, isotopically-enriched molybdenum metal must be recovered from the spent radiopharmaceutical solution used in NorthStar’s Technetium-99m generator and reused. The recycle process begins by recovering the metal from the aqueous potassium molybdate (K 2 MoO 4 ) solutions as molybdenum trioxide (MoO 3 ) employing a process developed at Argonne National Laboratory. The MoO 3 powder is subsequently reduced to molybdenum metal powder which can be blended with new powder and further processed into a flowable form to be used to produce target disks for irradiation. The molybdenum oxide reduction process has been examined and scaled to produce kilogram quantities of metal powder suitable for processing into a useable form employing spray drying or similar technique and ultimately used for target fabrication.

36 MATERIALS SCIENCE↗

Compaction and Sintering of Mo Powders

To support the development of Mo-99 production by NorthStar Medical Technologies, LLC, Mo metal powders were evaluated for compaction and sintering characteristics as they relate to Mo-100 accelerator target disk fabrication. Powders having a natural isotope distribution and enriched Mo-100 powder were examined. Various powder characteristics are shown to have an effect on both the compaction and sintering behavior. Natural Mo powders could be cold pressed directly to >90% density. All of the powders, including the Mo-100 samples, could be sintered after cold pressing to >90% density. As an example, a compacted Mo-100 disk reached 89.7% density (9.52 g/cm3) after sintering at 1000 C for 1 hr. in flowing Ar/4%H2. Higher sintering temperatures were required for other powder samples. The relationships between processing conditions and the resulting densities of consolidated Mo disks will be presented.

Nunn, Stephen D↗