Engineering topics

Bryant, Robert

Publications and source records attributed to Bryant, Robert.

4 records

NASA NTRS2019

Viscoelastic Characterization of Polymers for Deployable Composite Booms

Deployable space structures have been built from thin-walled fiber-reinforced polymer composite materials due to their high specific strength, high specific stiffness, and bistability. However, the inherent viscoelastic behavior of the resin matrix can cause dimensional instability when parts are stored under strain. The extended time of stowage between assembly and deployment in space can result in performance degradation and in the worst case, mission failure. In this study, the viscoelastic properties of candidate commercial polymers for deployable boom structures of solar sails were evaluated. Stress relaxation master curves of the candidate polymers were used to predict the relaxation that would occur in 1 year at room temperature under relatively low strains of ~0.1%. A bismaleimide (BMI) showed less stress relaxation (about 20%) than the baseline Novolac epoxy (about 50%). Carbon fiber composites fabricated with the BMI resin showed a 44% improvement in relaxation compared to the baseline epoxy composite. Other difunctional and tetrafunctional epoxies, thermoplastic, and thermosetting polyimides were also evaluated.

Kang, Jin Ho↗

NASA NTRS2019

Durability Characterization of Mechanical Interfaces in Solar Sail Membrane Structures

The construction of a solar sail from commercially available metallized film presents several challenges. The solar sail membrane is made by seaming together strips of metallized polymer film. This requires seaming together a preselected width and thickness of a base material into the required geometry, and folding the assembled sail membranes into a small stowage volume prior to launch. The sail membranes must have additional features for connecting to rigid structural elements (e.g., sail booms) and must be electrically grounded to the spacecraft bus to prevent charge build up. Space durability of the material and mechanical interfaces of the sail membrane assemblies will be critical for the success of any solar sail mission. In this study, interfaces of polymer/metal joints in a representative solar sail membrane assembly were tested to ensure that the adhesive interfaces and the fastening grommets could withstand the temperature range and expected loads required for mission success. Various adhesion methods, such as surface treatment, commercial adhesives, and fastening systems, were experimentally evaluated and will be discussed.

Interface↗

NASA NTRS2005

Development of Flexible Multilayer Circuits and Cables

A continuing program addresses the development of flexible multilayer electronic circuits and associated flexible cables. This development is undertaken to help satisfy aerospace-system-engineering requirements for efficient, lightweight electrical and electronic subsystems that can fit within confined spaces, adhere to complexly shaped surfaces, and can be embedded within composite materials. Heretofore, substrate layers for commercial flexible circuitry have been made from sheets of Kapton (or equivalent) polyimide and have been bonded to copper conductors and to other substrate layers by means of adhesives. The substrates for the present developmental flexible circuitry are made from thin films of a polyimide known as LaRC(TM)-SI. This polyimide is thermoplastic and, therefore, offers the potential to eliminate delamination and the need for adhesives. The development work undertaken thus far includes experiments in the use of several techniques of design and fabrication (including computer-aided design and fabrication) of representative flexible circuits. Anticipated future efforts would focus on multilayer bonding, fabrication of prototypes, and overcoming limitations.

Barnes, Kevin N.↗

NASA NTRS2003

Method of Fabricating a Piezoelectric Composite Apparatus

A method for fabricating a piezoelectric macro-fiber composite actuator comprises providing a piezoelectric material that has two sides and attaching one side upon an adhesive backing sheet. The method further comprises slicing the piezoelectric material to provide a plurality of piezoelectric fibers in juxtaposition. A conductive film is then adhesively bonded to the other side of the piezoelectric material, and the adhesive backing sheet is removed. The conductive film has first and second conductive patterns formed thereon which are electrically isolated from one another and in electrical contact with the piezoelectric material. The first and second conductive patterns of the conductive film each have a plurality of electrodes to form a pattern of interdigitated electrodes. A second film is then bonded to the other side of the piezoelectric material. The second film may have a pair of conductive patterns similar to the conductive patterns of the first film.

Wilkie, W. Keats↗