Search NASA⌕ Search

Engineering topics

Buchenauer, Dean

Publications and source records attributed to Buchenauer, Dean.

Influence of dynamic annealing of irradiation defects on the deuterium retention behaviors in tungsten irradiated with neutron

Tungsten (W) samples were damaged by neutron and 6.4 MeV Fe-ion irradiation above 1000 K simulating the divertor operation temperature. Deuterium (D) retention properties were examined by decorating the damaged W with D and subsequent thermal desorption spectroscopy (TDS) measurements. Vacancy clusters were the major D trapping site in the W irradiated with Fe-ion at 873 K, although D retention by vacancy clusters decreased in the W irradiated with Fe-ion at 1173 K due to dynamic annealing. The D de-trapping activation energy from vacancy clusters was found to be 1.85 eV. D retention in neutron damage W was larger than that damaged by Fe-ion due to the uniform distribution of irradiation defects. The D desorption behaviors from neutron damaged W was simulated well by assuming the D de-trapping activation energy to be 1.52 eV.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Retention properties in displacement damaged ultra-fine grain tungsten exposed to divertor plasma

One of the main advantages of using tungsten (W) as a plasma facing material (PFM) is its low uptake and retention of tritium. However, in high purity (ITER grade) W, hydrogenic retention increases significantly with neutron-induced displacement damage in the W lattice. This experiment examines an alternative W grade PFM, ultra-fine grain (UFG) W, to compare its retention properties with ITER grade W after 12 MeV Si ion displacement damage up to 0.6 dpa (displacements per atom.) Following exposure to plasma in the DIII-D divertor, D retention was then assessed with Nuclear Reaction Analysis (NRA) depth profiling up to 3.5 µm and thermal desorption spectrometry (TDS). Undamaged specimens were also included in our test matrix for comparison. For all samples, D release peaks were observed during TDS at approximately 200 °C and 750 °C. For the ITER-grade W specimens, the intensity of the 750 °C release peak was more pronounced for specimens that had been pre-damaged. Conversely, UFG samples that had been damaged by 12 MeV Si showed enhancement of the lower temperature release peak (200 °C). NRA profiles also reveal a higher D concentration for UFG W samples up to the peak in the damage profile at a depth of 2 m. Overall, we observed that the total trapped inventory in UFG W was 20% higher than ITER grade W in the undamaged case and 10% higher in the damaged case. A comparison of NRA and TDS data indicates that a larger fraction of the total retained D is trapped near the surface (86–100%) in UFG W pre-damaged to 0.6 dpa compared with ITER grade W (39–61%). Further examination of the UFG material with microscopy is recommended for a definitive determination of the types of defects responsible for D trapping. Our results highlight some potential trade-offs associated UFG W regarding its performance from a tritium retention standpoint. That said, our TDS results indicate that this enhanced inventory can be released by baking at relatively low temperatures (<500 °C), providing an avenue for minimizing tritium retention in this material that would be practical for implementation in a tokamak.

Barton, J↗

Japan-US Joint Research Project PHENIX (2013–2018); Heat Transfer Tests, Neutron Irradiation and Post-Irradiation Examinations for Development of He-Cooled Tungsten Divertor

The goal of the Japan-US joint research project PHENIX (2013–2018) is to understand the feasibility of He-cooled W divertor for DEMO applications. To achieve this goal, the project has three major objectives: (1) to understand heat transfer in a divertor module cooled with high-temperature and high-pressure He gas, (2) to establish database on thermomechanical properties of W materials after high temperature (~500, ~800 and ~1100 °C) neutron irradiation with fusion-relevant energy spectrum, and (3) to clarify tritium (T) trapping and permeation in neutron-irradiated W materials. Heat transfer tests for a He-cooled modular divertor with multi-jet (HEMJ) have been performed, and the problem of heat transfer degradation by re-laminarization was identified.The irradiation capsule with thermal neutron shielding was designed for high temperature neutron irradiation in the High Flux Isotope Reactor (HFIR), Oak Ridge National Laboratory (ORNL) with fusion-relevant transmutation. The expected damage level is 1–1.5 displacements per atom (dpa). Heat load resistance, thermal conductivity, mechanical properties and microstructures are examined in ORNL after the irradiation. Mechanical properties of W single crystal samples irradiated with neutrons in HFIR at 90– 850 °C without thermal neutron shielding were examined for comparison. Significant hardening was observed after irradiation to >1 dpa. Microstructural examinations revealed that the hardening was mainly caused by formation of irradiation-induced precipitates consisting of W, Re and Os. Comparison with new samples irradiated in the capsule with thermal neutron shielding will show the effects of irradiation temperatures and transmutation elements. Retention and permeation of hydrogen isotopes including T in neutron-irradiated samples are examined in Idaho National Laboratory, and permeation of H and D in samples damaged with surrogate irradiations (heavy ions, electrons, etc.) is measured in Sandia National Laboratories, Livermore, to study hydrogen-defect interactions in wider conditions. The measurement of D retention in the single crystal W sample after neutron irradiation to 0.1 dpa at 360 °C and subsequent plasma exposure at 400 °C showed significant trapping effects by radiation-induced defects.

Ueda, Yoshio↗

Progress in the U.S./Japan PHENIX Project for the Technological Assessment of Plasma Facing Components for DEMO Reactors

The PHENIX Project is a 6-year U.S./Japan bilateral, multi-institutional collaboration program for the Technological Assessment of Plasma Facing Components for DEMO Reactors. The goal is to address the technical feasibility of helium-cooled divertor concepts using tungsten as the armor material in fusion power reactors. The project specifically attempts to (1) improve heat transfer modeling for helium-cooled divertor systems through experiments including steady-state and pulsed high-heat-load testing, (2) understand the thermomechanical properties of tungsten metals and alloys under divertor-relevant neutron irradiation conditions, and (3) determine the behavior of tritium in tungsten materials through high-flux plasma exposure experiments. The High Flux Isotope Reactor and the Plasma Arc Lamp facility at Oak Ridge National Laboratory, the Tritium Plasma Experiment facility at Idaho National Laboratory, and the helium loop at Georgia Institute of Technology are utilized for evaluation of the response to high heat loads and tritium interactions of irradiated and unirradiated materials and components. This paper provides an overview of the progress achieved during the first 3 years and discusses the plan for the remainder of the project.

Kato, Yutai↗

The Design and Use of Tungsten Coated TZM Molybdenum Tile Inserts in the DIII-D Tokamak Divertor

Future tokamak devices are envisioned to utilize a high-Z metal divertor with tungsten as theleading candidate. However, tokamak experiments with tungsten divertors have seen significantdetrimental effects on plasma performance. The DIII-D tokamak presently has carbon as theplasma facing surface but to study the effect of tungsten on the plasma and its migration aroundthe vessel, two toroidal rows of carbon tiles in the divertor region were modified with high-Zmetal inserts, composed of a molybdenum alloy (TZM) coated with tungsten. A dedicated twoweek experimental campaign was run with the high-Z metal inserts. One row was coated withtungsten containing naturally occurring levels of isotopes. The second row was coated withtungsten where the isotope 182W was enhanced from the natural level of 26% up to greater than90%. The different isotopic concentrations enabled the experiment to differentiate between thetwo different sources of metal migration from the divertor. Various coating methods wereexplored for the deposition of the tungsten coating, including chemical vapor deposition,electroplating, vacuum plasma spray, and electron beam physical vapor deposition. The coatingswere tested to see if they were robust enough to act as a divertor target for the experiment. Testsincluded cyclic thermal heating using a high power laser and high-fluence deuterium plasmabombardment. The issues associate with the design of the inserts (tile installation, thermal stress,arcing, leading edges, surface preparation, etc.), are reviewed. The results of the tests used toselect the coating method and preliminary experimental observations are presented.

Holtrop, Kurt↗

Development of a plasma driven permeation experiment for TPE

Experiments on retention of hydrogen isotopes (including tritium) at temperatures less than 800 ?C have been carried out in the Tritium Plasma Experiment (TPE) at Idaho National Laboratory [1,2]. To provide a direct measurement of plasma driven permeation in plasma facing materials at temperatures reaching 1000 ?C, a new TPE membrane holder has been built to hold test specimens (=1 mm in thickness) at high temperature while measuring tritium permeating through the membrane from the plasma facing side. This measurement is accomplished by employing a carrier gas that transports the permeating tritium from the backside of the membrane to ion chambers giving a direct measurement of the plasma driven tritium permeation rate. Isolation of the membrane cooling and sweep gases from TPE’s vacuum chamber has been demonstrated by sealing tests performed up to 1000 ?C of a membrane holder design that provides easy change out of membrane specimens between tests. Simulations of the helium carrier gas which transports tritium to the ion chamber indicate a very small pressure drop (~700 Pa) with good flow uniformity (at 1000 sccm). Thermal transport simulations indicate that temperatures up to 1000 ?C are expected at the highest TPE fluxes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗