Search NASA⌕ Search

Engineering topics

Buck, Edgar C

Publications and source records attributed to Buck, Edgar C.

At least 19 records

Single-Pass Flow-Through Test Elucidation of Weathering Behavior and Evaluation of Contaminant Release Models for Hanford Tank Residual Radioactive Waste

Contaminant release models are required to evaluate and predict long-term environmental impacts of even residual amounts of high-level radioactive waste after cleanup and closure of radioactively contaminated sites such as the DOE’s Hanford Site. More realistic and representative models have been developed for release of uranium, technetium, and chromium from Hanford Site tanks C-202, C-203, and C-103 residual wastes using data collected with a single-pass flow-through test (SPFT) method. These revised models indicate that contaminant release concentrations from these residual wastes will be considerably lower than previous estimates based on batch experiments. For uranium, a thermodynamic solubility model provides an effective description of uranium release, which can account for differences in pore fluid chemistry contacting the waste that could occur through time and as a result of different closure scenarios. Under certain circumstances in the SPFT experiments various calcium rich precipitates (calcium phosphates and calcite) form on the surfaces of the waste particles, inhibiting dissolution of the underlying uranium phases in the waste. This behavior was not observed in previous batch experiments. For both technetium and chromium, empirical release models were developed. In the case of technetium, release from all three wastes was modeled using an equilibrium Kd model. For chromium release, a constant concentration model was applied for all three wastes.

chromium↗

Controls on Soluble Pu Concentrations in PuO2/Magnetite Suspensions

Time-dependent reduction of PuO2(am) was studied over a range of pH values in the presence of aqueous Fe(II) and magnetite (Fe3O4) nanoparticles. At early time frames (up to 56 days) very little aqueous Pu was mobilized from PuO2(am), even though measured pH and redox potentials, coupled to equilibrium thermodynamic modeling indicated the potential for significant reduction of PuO2(am) to relatively soluble Pu(III). Introduction of Eu(III) or Nd(III) to the suspensions as competitive cations to displace possible sorbed Pu(III) resulted in the release of significant concentrations of aqueous Pu. However, the similarity of aqueous Pu concentrations that resulted from the introduction of Eu(III)/Nd(III) to suspensions with and without magnetite indicated that the Pu was displaced from the PuO2(am), not from magnetite. The fact that soluble forms of Pu can be displaced from the surface of PuO2(am) represents a potential, but previously unidentified, source of Pu to aqueous solution or subsurface groundwaters.

Environmental Molecular Sciences Laboratory↗

Investigations into the Polymorphs and Hydration Products of UO3

This work focuses on progress in gaining a better understanding of the polymorphic nature of the UO{sub 3} and UO{sub 3}-water system; one of several important materials associated with the nuclear fuel cycle. The UO{sub 3}-water system is complex and has not been fully characterized, even though these species are common throughout the fuel cycle. For example, most production schemes for UO{sub 3} result in a mixture of up to six different polymorphic phases, and small differences in these conditions will affect phase genesis that ultimately results in measureable changes to the end product. Here we summarize our efforts to better characterize the UO{sub 3}-water system with optical techniques for the purpose of developing some predictive capability of estimating process history and utility, e.g. for polymorphic phases of unknown origin. Specifically, we have investigated three industrially relevant production pathways of UO{sub 3} and discovered a previously unknown low temperature route to {beta}-UO{sub 3}. Powder x-ray diffraction and optical spectroscopies were utilized in our characterization of the UO{sub 3}-water system. Pure phases of UO{sub 3}, its hydrolysis products and starting materials were used to establish optical spectroscopic signatures for these compounds. Preliminary aging studies were conducted on the {alpha}- and {gamma}-phases of UO{sub 3}.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Biotic and Abiotic Reduction and Solubilization of Pu(IV)O2•xH2O(am) as Affected by Anthraquinone-2,6-disulfonate (AQDS) and Ethylenediaminetetraacetate (EDTA)

In the presence of hydrogen (H{sub 2}), the synthetic chelating agent ethylenediaminetetraacetate (EDTA), and the electron shuttle anthraquinone-2,6-disulfonate (AQDS), the dissimilatory metal-reducing bacteria (DMRB) Shewanella oneidensis and Geobacter sulfurreducens both reductively solubilized 100% of added 0.5 mM plutonium (IV) hydrous oxide (Pu(IV)O{sub 2} {lg_bullet} xH{sub 2}O{sub (am)}) in {approx}24 h at pH 7 in a non-complexing buffer. In the absence of AQDS, bioreduction was much slower ({approx}22 days) and less extensive ({approx}83-94%). In the absence of DMRB but under comparable conditions, 89% (without AQDS) to 98% (with AQDS) of added 0.5 mM PuO{sub 2} {lg_bullet} xH{sub 2}O{sub (am)} was reductively solubilized over 418 days. Under comparable conditions but in the absence of EDTA, <0.001% of the 0.5 mM PuO{sub 2} {lg_bullet} xH{sub 2}O{sub (am)} was solubilized, with or without bacteria. However, Pu(aq) increased by as much as an order of magnitude in some EDTA-free treatments, both biotic and abiotic, and increases in solubility were associated with the production of both Pu(OH)3(am) and Pu(III)(aq). Incubation with DMRB in the absence of EDTA increased the polymeric and crystalline content of the PuO{sub 2} {lg_bullet} xH{sub 2}O{sub (am)} and also decreased Pu solubility in 6-N HCl. Results from an in vitro assay demonstrated electron transfer to PuO{sub 2} {lg_bullet} xH{sub 2}O{sub (am)} from the S. oneidensis outer-membrane c-type cytochrome MtrC, and EDTA increased the oxidation of MtrC by PuO{sub 2} {lg_bullet} xH{sub 2}O{sub (am)}. Our results suggest that PuO{sub 2} {lg_bullet} xH{sub 2}O{sub (am)} biotic and abiotic reduction and solubilization may be important in anoxic, reducing environments, especially where complexing ligands and electron shuttling compounds are present.

08 HYDROGEN↗

Immobilization of 99-Technetium (VII) by Fe(II)-Goethite and Limited Reoxidation

During the nuclear waste vitrification process volatilized {sup 99}Tc will be trapped by melter off-gas scrubbers and then washed out into caustic solutions, and plans are currently being contemplated for the disposal of such secondary waste. Solutions containing pertechnetate [{sup 99}Tc(VII)O{sub 4}{sup -}] were mixed with precipitating goethite and dissolved Fe(II) to determine if an iron (oxy)hydroxide-based waste form can reduce Tc(VII) and isolate Tc(IV) from oxygen. The results of these experiments demonstrate that Fe(II) with goethite efficiently catalyzes the reduction of technetium in deionized water and complex solutions that mimic the chemical composition of caustic waste scrubber media. Identification of the phases, goethite + magnetite, was performed using XRD, SEM and TEM methods. Analyses of the Tc-bearing solid products by XAFS indicate that all of the Tc(VII) was reduced to Tc(IV) and that the latter is incorporated into goethite or magnetite as octahedral Tc(IV). Batch dissolution experiments, conducted under ambient oxidizing conditions for more than 180 days, demonstrated a very limited release of Tc to solution (2-7 {micro}g Tc/g solid). Incorporation of Tc(IV) into the goethite lattice thus provides significant advantages for limiting reoxidation and curtailing release of Tc disposed in nuclear waste repositories.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Hanford Waste Physical and Rheological Properties: Data and Gaps

The Hanford Site in Washington State manages 177 underground storage tanks containing approximately 250,000 m3 of waste generated during past defense reprocessing and waste management operations. These tanks contain a mixture of sludge, saltcake and supernatant liquids. The insoluble sludge fraction of the waste consists of metal oxides and hydroxides and contains the bulk of many radionuclides such as the transuranic components and 90Sr. The saltcake, generated by extensive evaporation of aqueous solutions, consists primarily of dried sodium salts. The supernates consist of concentrated (5-15 M) aqueous solutions of sodium and potassium salts. The 177 storage tanks include 149 single-shell tanks (SSTs) and 28 double -hell tanks (DSTs). Ultimately the wastes need to be retrieved from the tanks for treatment and disposal. The SSTs contain minimal amounts of liquid wastes, and the Tank Operations Contractor is continuing a program of moving solid wastes from SSTs to interim storage in the DSTs. The Hanford DST system provides the staging location for waste feed delivery to the Department of Energy (DOE) Office of River Protection’s (ORP) Hanford Tank Waste Treatment and Immobilization Plant (WTP). The WTP is being designed and constructed to pretreat and then vitrify a large portion of the wastes in Hanford’s 177 underground waste storage tanks.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Heterogeneous Reduction of PuO2 with Fe(II): Importance of the Fe(III) Reaction Product

Abstract Heterogeneous reduction of actinides in higher and more soluble oxidation states to lower more insoluble oxidation states by reductants such as Fe(II) has been the subject of intensive study for more than two decades. However, Fe(II)-induced reduction of sparingly soluble Pu(IV) to the more soluble lower oxidation state Pu(III) has been much less studied even though such reactions can potentially increase the mobility of Pu in the subsurface. Thermodynamic calculations are presented that show how differences in the free energy of various possible solid-phase Fe(III) reaction products can greatly influence aqueous Pu(III) concentrations resulting from reduction of PuO2(am) by Fe(II). We present the first experimental evidence that reduction of PuO2(am) to Pu(III) by Fe(II) was enhanced when the Fe(III) mineral goethite was spiked into the reaction. The effect of goethite on reduction of Pu(IV) was demonstrated by measuring the time-dependence of total aqueous Pu concentration, its oxidation state, and system pe/pH. We also re-evaluated established protocols for determining Pu(III) [(Pu(III) + Pu(IV)) - Pu(IV)] by using thenoyltrifluoroacetone (TTA) in toluene extractions; the study showed that it is important to eliminate dissolved oxygen from the TTA solutions for accurate determinations. More broadly, this study highlights the importance of the Fe(III) reaction product in actinide reduction rate and extent by Fe(II).

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Imaging Hydrated Microbial Extracellular Polymers: Comparative Analysis by Electron Microscopy

Microbe-mineral and -metal interactions represent a major intersection between the biosphere and geosphere but require high-resolution imaging and analytical tools for investigating microscale associations. Electron microscopy has been used extensively for geomicrobial investigations and although used bona fide, the traditional methods of sample preparation do not preserve the native morphology of microbiological components, especially extracellular polymers. Herein, we present a direct comparative analysis of microbial interactions using conventional electron microscopy approaches of imaging at room temperature and a suite of cryo-electron microscopy methods providing imaging in the close-to-natural hydrated state. In situ, we observed an irreversible transformation of bacterial extracellular polymers during the traditional dehydration-based sample preparation that resulted in the collapse of hydrated gel-like EPS into filamentous structures. Dehydration-induced polymer collapse can lead to inaccurate spatial relationships and hence could subsequently affect conclusions regarding nature of interactions between microbial extracellular polymers and their environment.

59 BASIC BIOLOGICAL SCIENCES↗

Analytical Plan for Roman Glasses

Roman glasses that have been in the sea or underground for about 1800 years can serve as the independent “experiment” that is needed for validation of codes and models that are used in performance assessment. Two sets of Roman-era glasses have been obtained for this purpose. One set comes from the sunken vessel the Iulia Felix; the second from recently excavated glasses from a Roman villa in Aquileia, Italy. The specimens contain glass artifacts and attached sediment or soil. In the case of the Iulia Felix glasses quite a lot of analytical work has been completed at the University of Padova, but from an archaeological perspective. The glasses from Aquileia have not been so carefully analyzed, but they are similar to other Roman glasses. Both glass and sediment or soil need to be analyzed and are the subject of this analytical plan. The glasses need to be analyzed with the goal of validating the model used to describe glass dissolution. The sediment and soil need to be analyzed to determine the profile of elements released from the glass. This latter need represents a significant analytical challenge because of the trace quantities that need to be analyzed. Both pieces of information will yield important information useful in the validation of the glass dissolution model and the chemical transport code(s) used to determine the migration of elements once released from the glass. In this plan, we outline the analytical techniques that should be useful in obtaining the needed information and suggest a useful starting point for this analytical effort.

54 ENVIRONMENTAL SCIENCES↗

Spectroscopic Characterization of Actinide Materials

Advanced spectroscopic techniques provide new and unique tools for unraveling the nature of the electronic structure of actinide materials. Inelastic neutron scattering experiments that address temporal aspects of lattice and magnetic fluctuations, probe electromagnetic multipole interactions and the coupling between electronic and vibrational degrees of freedom. Nuclear magnetic resonance clearly demonstrates different magnetic ground states at low temperature. Photoemission spectroscopies provide information on the occupied part of the electron density of states and have been used to investigate the momentum-resolved electronic structure and the topology of the Fermi surface in a variety of actinide compounds. Furthermore, x-ray absorption and electron energy-loss spectroscopies have been used to probe the relativistic nature, the occupation number, and the degree of localization of 5f electrons across the actinide series. More recently, element and edge-specific resonant and non-resonant inelastic x-ray scattering experiments have provided the opportunity of measuring elementary electronic excitations with higher resolution than traditional absorption techniques. Here, we will discuss the results obtained by most of these different spectroscopic techniques in studying the electronic and magnetic properties of selected actinide compounds, chosen as typical examples of systems with 5f electrons having an itinerant or a localized character, or lying near the localization-delocalization boundary.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Characterization of Glass-Like Fragments from the 3714 Building

This report describes characterization of a sample obtained from the 3714 building in the 300 Area. Characterization of this unknown material was required for the demonolition activities in the 300 Area. The object of the study was to dertermine the nature of the material, composition, possible structure, evidence for hazards components. The green material is a sodium alumino-silicate glass. This conclusion is based on the composition provided by SEM-EDS, and the images that suggest a glass-like morphology. Further analysis with Ramin and/or infrared could be used to determine the presence of any organics.

300 Area↗

Influence of Dynamical Conditions on the Reduction of UVI at the Magnetite-Solution Interface

The heterogeneous reduction of UVI to UIV by ferrous iron is a potentially key process influencing the fate and transport of U in the environment. The reactivity of both sorbed and structural FeII has been studied for numerous substrates, including magnetite. The results from UVI-magnetite experiments have been variable, ranging from no reduction to clear evidence for the formation of UIV. In this contribution, we used XAS and high resolution (+cryogenic) XPS to study the interaction of UVI with nano-particulate magnetite. The results indicated that UVI was partially reduced to UV with no evidence of UIV. However, thermodynamic calculations indicated that mixed-valence U phases with average oxidation states below (V) should have been stable, indicating that the system was not in redox equilibrium. A reaction pathway that involves incorporation of U and stabilization of UV and UVI in secondary phases is invoked to explain the observations.

Environmental Molecular Sciences Laboratory↗

Verifying the Presence of Low Levels of Neptunium in a Uranium Matrix with Electron Energy-Loss Spectroscopy

This paper examines the problems associated with the analysis of low levels of neptunium (Np) in a uranium (U) matrix with electron energy-loss spectroscopy (EELS) on the transmission electron microscope (TEM). The detection of Np in a matrix of uranium (U) can be impeded by the occurrence of a plural scattering event from U (U-M5 + U-O4,5) that results in severe overlap on the Np-M5 edge at 3665 eV. Low levels (1600 - 6300 ppm) of Np can be detected in U solids by confirming the energy gap between the Np-M5 and Np-M4 edges is at 184 eV and showing that the M4/M5 ratio for the Np is smaller than that for U. The Richardson-Lucy deconvolution method was applied to energy-loss spectral images and was shown to increase the signal to noise. This method also improves the limits of detection for Np in a U matrix.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

The Formation and Modeling of Colloids from the Corrosion of Nuclear Waste Forms

This paper describes a model for determining the stability and associated radionuclide concentrations of colloids that might be present in the nuclear waste package environment from degradation of the nuclear waste forms. The model simplifies radionuclide–colloid behavior by assuming that all colloids can be defined as either smectite clay, a mixed actinide-bearing rare earth-zirconium oxide, iron oxyhydroxide (ferrihydrite {FeOOH}, or uranophane {Ca(UO2)2(SiO3OH)2(H2O)5}. However, for the purposes of predictive stability modeling, the colloids are conceptually represented as montmorillonite, ZrO2, hematite, and meta autunite, respectively. The model uses theoretical calculations and laboratory data to determine the stability of modeled colloids with ionic strength and pH. The true nature of colloid composition and heterogeneity, generation, and flocculation will be extremely complex, involving the formation of numerous types of phases, often depending on the composition of the various waste forms and waste package materials. This model strives to capture the uncertainty of the real system using theoretical models. In this paper, one of the four representative colloids designed to capture the behavior of the spent fuel derived colloids is described in detail.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

CHARACTERIZATION OF HIGH PHOSPHATE RADIOACTIVE TANK WASTE AND SIMULANT DEVELOPMENT

A sample of high-level radioactive tank waste was characterized to provide a basis for developing a waste simulant. The simulant is required for engineered-scaled testing of pretreatment processes in a non-radiological facility. The waste material examined was derived from the bismuth phosphate process, which was the first industrial process implemented to separate plutonium from irradiated nuclear fuel. The bismuth phosphate sludge is a complex mixture rich in bismuth, iron, sodium, phosphorus, silicon, and uranium. The form of phosphorus in this particular tank waste material is of specific importance because that is the primary component (other than water-soluble sodium salts) that must be removed from the high-level waste solids by pretreatment. This work shows unequivocally that the phosphorus present in this waste material is not present as bismuth phosphate. Rather, the phosphorus appears to be incorporated mostly into an amorphous iron(III) phosphate species. The bismuth in the sludge solids is best described as bismuth ferrite, BiFeO3. Infrared spectral data, microscopy, and thermal analysis data are presented to support these conclusions. The behavior of phosphorus during caustic leaching of the bismuth phosphate sludge solids is also discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development and Characterization of Boehmite Component Simulant

According to Bechtel National Inc.’s (BNI’s) Test Specification 24590-PTF-TSP-RT-06-006, Rev 0, “Simulant Development to Support the Development and Demonstration of Leaching and Ultrafiltration Pretreatment Processes,” simulants for boehmite, gibbsite, and filtration are to be developed that can be used in subsequent bench and integrated testing of the leaching/filtration processes. These simulants will then be used to demonstrate the leaching process and to help refine processing conditions that may impact safety basis considerations (Smith 2006). This report documents the results of the boehmite simulant development and blended simulant crossflow ultrafiltration leaching completed in accordance with the test plan TP-RPP-WTP-469 Rev 0 (WTP Doc. No. 24590- 101-TSA-W000-0004-182-00001 Rev 00A) prepared and approved in response to the cited test specification. This report also includes the results of the aluminate and anion effect on boehmite dissolution performed in accordance with the test plan TP-RPP-WTP-509, Rev 0 (WTP Doc. No. 24590-101-TSA-W000-0004-72-00019 Rev 00A) prepared and approved in response to the Test Specification 24590-WTP-TSP-RT-07-004, Rev 0 (Sundar 2007).

Russell, Renee L↗

Development and Characterization of Boehmite Component Simulant

According to Bechtel National Inc.’s (BNI’s) Test Specification 24590-PTF-TSP-RT-06-006, Rev 0, “Simulant Development to Support the Development and Demonstration of Leaching and Ultrafiltration Pretreatment Processes,” simulants for boehmite, gibbsite, and filtration are to be developed that can be used in subsequent bench and integrated testing of the leaching/filtration processes. These simulants will then be used to demonstrate the leaching process and to help refine processing conditions that may impact safety basis considerations (Smith 2006). This report documents the results of the boehmite simulant development.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗