Engineering topics

Buggeln, R. C.

Publications and source records attributed to Buggeln, R. C..

11 records

NASA NTRS1990

Two- and three-dimensional blade vortex interactions

A three-dimensional time dependent Navier-Stokes analysis was applied to the rotor blade vortex interaction (BVI) problem. The numerical procedure is an iterative implicit procedure using three point central differences to represent spatial derivatives. A series of calculations were made to determine the time steps, pseudo-time steps, iterations, artificial dissipation level, etc. required to maintain a nondissipative vortex. Results show the chosen method to have excellent non-dissipative properties provided the correct parameters are chosen. This study was used to set parameters for both two- and three-dimensional blade vortex interaction studies. The two-dimensional study considered the interaction between a vortex and a NACA0012 airfoil. The results showed the detailed physics during the interaction including the pressure pulse propagating from the blade. The simulated flow physics was qualitatively similar to that experimentally observed. The 2-D BVI phenomena is the result of the buildup and violent collapse of the shock waves and local supersonic pockets on the blade surfaces. The resulting pressure pulse build-up appears to be centered at the blade leading edge. The three-dimensional interaction study considered the case of a vortex at 20 deg incidence to the blade leading edge. Although the qualitative results were similar to that of the two-dimensional interaction, details clearly showed the three-dimensional nature of the interaction process.

Davoudzadeh, F.↗

NASA NTRS1989

Solution of the incompressible Navier-Stokes equations using artificial compressibility methods

A modified artificial compressibility formulation is derived from a preconditioned low Mach number compressible formulation, and these two methods are compared on a two-dimensional laminar leading edge flow using a LBI/ADI solution algorithm. The two methods are essentially equivalent with appropriate preconditioning parameters and have the same convergence rates and efficiency, giving 4 orders of residual reduction in about 75 iterations with a vectorized CRAY-XMP run time of 20 seconds for 3000 grid points.

Briley, W. R.↗

NASA NTRS1987

Two- and three-dimensional turbine blade row flow field simulations

Work performed in the numerical simulation of turbine passage flows via a Navier-Stokes approach is discussed. Both laminar and turbulent simulations in both two and three dimensions are discussed. An outline of the approach, background, and an overview of the results are given.

Buggeln, R. C.↗

NASA NTRS1987

Calculation of helicopter rotor blade/vortex interaction by Navier-Stokes procedures

Interactions of a modern rotor blade with concentrated tip vortices from the previous blades can have a significant influence on the airloads and the aeroacoustics of a helicopter. A better understanding of the blade/vortex interaction process and a method of analyzing its flow field would provide valuable help in the design of helicopters. The work discussed herein represents an initial effort in applying a 3-D, time-dependent Navier-Stokes simulation to the blade vortex interaction problem. The numerical approach is the Linearized Block Implicit (LBI) technique. In this initial effort, consideration is given to the interaction of a wing of idealized geometry and a vortex whose axis is aligned at an arbitrary angle to the wing. The calculations are made for laminar, subsonic flow, and show the time dependent pressure distribution and flow fields resulting from the interaction.

Kim, Y.-N.↗

NASA NTRS1986

Computation of multi-dimensional viscous supersonic jet flow

A new method has been developed for two- and three-dimensional computations of viscous supersonic flows with embedded subsonic regions adjacent to solid boundaries. The approach employs a reduced form of the Navier-Stokes equations which allows solution as an initial-boundary value problem in space, using an efficient noniterative forward marching algorithm. Numerical instability associated with forward marching algorithms for flows with embedded subsonic regions is avoided by approximation of the reduced form of the Navier-Stokes equations in the subsonic regions of the boundary layers. Supersonic and subsonic portions of the flow field are simultaneously calculated by a consistently split linearized block implicit computational algorithm. The results of computations for a series of test cases relevant to internal supersonic flow is presented and compared with data. Comparison between data and computation are in general excellent thus indicating that the computational technique has great promise as a tool for calculating supersonic flow with embedded subsonic regions. Finally, a User's Manual is presented for the computer code used to perform the calculations.

Kim, Y. N.↗

NASA NTRS1986

Computation of multi-dimensional viscous supersonic flow

A method has been developed for two- and three-dimensional computations of viscous supersonic jet flows interacting with an external flow. The approach employs a reduced form of the Navier-Stokes equations which allows solution as an initial-boundary value problem in space, using an efficient noniterative forward marching algorithm. Numerical instability associated with forward marching algorithms for flows with embedded subsonic regions is avoided by approximation of the reduced form of the Navier-Stokes equations in the subsonic regions of the boundary layers. Supersonic and subsonic portions of the flow field are simultaneously calculated by a consistently split linearized block implicit computational algorithm. The results of computations for a series of test cases associated with supersonic jet flow is presented and compared with other calculations for axisymmetric cases. Demonstration calculations indicate that the computational technique has great promise as a tool for calculating a wide range of supersonic flow problems including jet flow. Finally, a User's Manual is presented for the computer code used to perform the calculations.

Buggeln, R. C.↗

NASA NTRS1986

Turbine stator flow field simulations

The increased capability and accessibility of modern computers, coupled with increasingly sophisticated and accurate numerical and physical modeling, has led to a marked impact of numerical simulations upon current turbine design and research problems. The turbine section represents a considerable challenge as it contains significant regions of complex three-dimensional flow, including both aerodynamic and heat transfer phenomena. The focus of the present effort is the development of an efficient and accurate three-dimensional Navier-Stokes calculation procedure for application to the turbine stator and rotor problems. In particular, an effective procedure is sought which: (1) adequately represents the flow physics, (2) allows for sufficient resolution in regions of small length scale, and (3) has sufficiently good convergence properties so as to allow use on a regular basis.

Buggeln, R. C.↗

NASA NTRS1986

Numerical analysis of some supersonic viscous flows related to inlet and nozzle systems

A numerical method originally developed for three-dimensional supersonic inlet flow calculations is extended and applied to the study of two-dimensional and three-dimensional flows associated with arbitrary propulsion systems. The method is based on the forward spatial marching solution of a reduced form of the three-dimensional steady Navier-Stokes equations in which streamwise pressure gradients are retained in both the subsonic and supersonic regions. The present paper briefly describes the analysis and then shows three applications. In the first application, a wall transpiration study has been performed for the two-dimensional shock wave/turbulent boundary layer interaction flow field with application to an inlet configuration. The second application treats a rectangular high speed inlet with a swept sideplate including the effects of sideplate spillage. Finally, the method is utilized to analyze the interaction of an under-expanded supersonic jet with an ambient flow. Computed results are examined and compared with available experimental measurements. It is demonstrated that the present numerical method is capable of numerically simulating complex two- and three-dimensional flows relevant to hypersonic propulsion systems in a manner which both shows good agreement with data when such data is available, and which shows the complex flow features in the absence of data.

Kim, Y.-N.↗

NASA NTRS1985

Flow in a model turbine stator

In view of the complex nature of the flowfield in the hot section of gas turbine engines, the need to predict heat transfer and flow losses, the possible appearance of separation and strong secondary flows, etc., the present effort is focusing upon a Navier-Stokes approach to the three dimensional turbine stator problem. The advantages of a full Navier-Stokes approach are clear since when combined with a suitable turbulence model these equations represent the flow and heat transfer physics. In particular, the Navier-Stokes equations accurately represent possible separated regions and regions of significant secondary flow. In addition, the Navier-Stokes approach allows representation of the entire flow field by a single set of equations, thus avoiding problems associated with representing different regions of the flow by different equations and then matching flow regions.

Buggeln, R. C.↗

NASA NTRS1980

Development of a three-dimensional supersonic inlet flow analysis

A method for computing three dimensional flow in supersonic inlets is described. An approximate set of governing equations is given for viscous flows which have a primary flow direction. The governing equations are written in general orthogonal coordinates. These equations are modified in the subsonic region of the flow to prevent the phenomenon of branching. Results are presented for the two sample cases: a Mach number equals 2.5 flow in a square duct, and a Mach number equals 3.0 flow in a research jet engine inlet. In the latter case the computed results are compared with the experimental data. A users' manual is included.

Buggeln, R. C.↗

NASA NTRS1980

Computation of three-dimensional viscous supersonic flow in inlets

A new approach has been developed for the computation of the three-dimensional viscous supersonic flow with embedded subsonic regions adjacent to solid boundaries and is applied to a mixed-compression supersonic inlet typical of current designs. The approach uses a reduced form of the three-dimensional Navier-Stokes equations so that the resultant equations can be treated as an initial boundary value problem and thus be solved by non-iterative forward marching in space. The numerical procedure utilizes an efficient consistently-split linearized block implicit technique to solve the finite difference analogues to the set of governing partial differential equations.

Buggeln, R. C.↗