Search NASA⌕ Search

Engineering topics

Burkardt, L. A.

Publications and source records attributed to Burkardt, L. A..

6 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Uniform engine testing program phase 7: NASA Lewis Research Center second entry

The propulsion and Energetics Panel, Working Group 15, of the Advisory Group for Aerospace Research and Development (AGARD) is sponsoring a Uniform Engine Testing Program (UETP). In this program, two jet engines were tested under identical conditions in certain NATO altitude and ground-level facilities as a means of correlating these facilities. With this second entry, NASA documented engine deterioration that may have occurred since inception of the UETP. Additionally, NASA investigated anomalies discovered during review of data from the five facilities which had participated in the program between the two NASA entries.

Biesiadny, T. J.↗
NASA NTRS1981

Effect of a part-span variable inlet guide vane on the performance of a high-bypass turbofan engine

The ability of a part-span variable inlet guide vane to modulate the thrust of a high bypass turbofan engine was evaluated at altitude/Mach number conditions of 4572 m/0.6 and 9144 m/0.93. Fan-tip, gas generator and supercharger performance were also determined, both on operating lines and during fan duct throttling. The evaluation was repeated with the bypass splitter extended forward to near the fan blade trailing edge. Gross thrust attenuation of over 50% was achieved with 50 deg variable inlet guide vane closure at 100% corrected fan speed. Gas generator supercharger performance fell off with variable inlet guide vane closure but this loss was reduced when a splitter extension was added. The effect of variable inlet guide vane closure on gas generator performance was minimal.

Bobula, G. A.↗
NASA NTRS1981

Mixing effectiveness test of an exhaust gas mixer in a high bypass turbofan at altitude

Thermal mixing effectiveness characteristics of an eighteen lobe, scalloped and unscalloped, partial, forced mixer were measured in a high-bypass turbofan engine. Data were also obtained without the mixer installed, i.e. free mixing. Tests were conducted at four combinations of simulated flight conditions from 0.3 to 0.8 Mach number and from 6,096 meters (20,000 ft) to 13,715 m (45,000 ft) altitude. Mixing chamber lengths of L/D = 0.52 and 0.65 were tested. For this range of test conditions and mixer configurations the forced mixing effectiveness varied from 59 to 68 percent. Values of mixing effectiveness and total pressure loss were calculated from temperature and pressure data obtained at the mixer inlet and exhaust nozzle exit.

Cullom, R. R.↗
NASA NTRS1981

Effect of a part-span variable inlet guide vane on the performance of a high-bypass turbofan engine

The ability of a part span variable inlet guide vane (VIGV) to modulate the thrust of a high bypass turbofan engine was evaluated at altitude/Mach number conditions of 4572 m/0.6 and 9144 m/0.93. Fan tip, gas generator and supercharger performance were also determined, both on operating lines and during fan duct throttling. The evaluation was repeated with the bypass splitter extended forward to near the fan blade trailing edge. Gross thrust attentuation of over 50 percent was achieved with 50 degree VIGV closure at 100 percent corrected fan speed. Gas generator supercharger performance fell off with VIGV closure, but this loss was reduced when a splitter extension was added. The effect of VIVG closure on gas generator performance was minimal.

Bobula, G. A.↗
NASA NTRS1981

Mixing effectiveness test of an exhaust gas mixer in a high bypass turbofan at altitude

Thermal mixing effectiveness characteristics of an eighteen lobe, scalloped and unscalloped, partial, forced mixer were measured in a high-bypass turbofan engine. Data were also obtained without the mixer installed, i.e., free mixing. Tests were conducted at four combinations of simulated flight conditions from 0.3 to 0.8 Mach number and from 6,096 meters (20,000 ft) to 13,715 m (45,000 ft) altitude, mixing chamber lengths of L/D=0.52 and 0.65 were tested. For this range of test conditions and mixer configurations, the forced mixing effectiveness varied from 59 to 68 percent. Values of mixing effectiveness and total pressure loss were calculated from temperature and pressure data obtained at the mixer inlet and exhaust nozzle exit.

Cullom, R. R.↗