Search NASA⌕ Search

Engineering topics

Burkes, Douglas

Publications and source records attributed to Burkes, Douglas.

At least 19 records

Microstructure-dependent rate theory model of defect segregation and phase stability in irradiated polycrystalline LiAlO 2

We report gamma lithium aluminate (LiAlO 2 ) is a breeder material for tritium and is one of key components in a tritium-producing burnable absorber rod (TPBAR). Dissolution and precipitation of second phases such as LiAl 5 O 8 and voids are observed in irradiated LiAlO 2 . Such microstructure changes cause the degradation of thermomechanical properties of LiAlO 2 and affect tritium retention and release kinetics, and hence, the TPBAR performance. In this work, a microstructure-dependent model of radiation-induced segregation (RIS) has been developed for investigating the accumulation of species and phase stability in polycrystalline LiAlO 2 structures under irradiation. Three sublattices (i.e. [Li, Al, V] I [O, V o ] II [Li i , Al i , O i , V i ] III ), and concentrations of six diffusive species (i.e. Li; vacancy of Li or Al at [Li, Al, V] I sublattice, O vacancy at [O, V o ] II sublattice, and Li, Al and O interstitials at [Li i , Al i , O i , V i ] III interstitial sublattices; are used to describe spatial and temporal distributions of defects and chemistry. Microstructure-dependent thermodynamic and kinetic properties including the generation, reaction, and chemical potentials of defects and defect mobility are taken into account in the model. The parametric studies demonstrated the capability of the developed RIS model to assess the effect of thermodynamic and kinetic properties of defects on the segregation and depletion of species in polycrystalline structures and to explain the phase stability observed in irradiated LiAlO 2 samples. The developed RIS model will be extended to study the precipitation of LiAl 5 O 8 and voids and tritium retention by integrating the phase-field method.

36 MATERIALS SCIENCE↗

Microstructure-Dependent Rate Theory Model of Radiation-Induced Segregation in Binary Alloys

Conventional rate theory often uses the mean field concept to describe the effect of inhomogeneous microstructures on the evolution of radiation induced defect and solute/fission product segregation. However, the spatial and temporal evolution of defects and solutes determines the formation and spatial distribution of radiation-induced second phase such as precipitates and gas bubbles/voids, especially in materials with complicated microstructures and subject to high dose radiation. In this work, a microstructure-dependent model of radiation-induced segregation (RIS) has been developed to investigate the effect of inhomogeneous thermodynamic and kinetics properties of defects on diffusion and accumulations of solute A in AB binary alloys. Four independent concentrations: atom A, interstitial A, interstitial B, and vacancy on [A, B] sublattice are used as field variables to describe temporal and spatial distribution and evolution of defects and solute A. The independent concentrations of interstitial A and interstitial B allow to describe their different generation rates, thermodynamic and kinetic properties, and release the assumptions of interstitial generation and sink strength used in the conventional rate theory. Microstructure and concentration dependent chemical potentials of defects are used to calculate the driving forces of defect diffusions. With the model, the effects of defect chemical potentials and mobilities on the RIS in polycrystalline AB model alloys have been simulated. The results demonstrated the model capability in predicting defect evolution in materials with inhomogeneous thermodynamic and kinetic properties of defects. The model can be extended to materials with complicated microstructures such as a wide range of grain size distribution, coating structure and multiphases as well as radiation-induced precipitation subject to severe radiation damage.

36 MATERIALS SCIENCE↗

Thermal properties of U-Mo alloys irradiated under high fission power density

A variety of physical and thermal property measurements made on irradiated U-Mo alloy monolithic fuel samples with a Zr diffusion barrier and clad in Al alloy 6061 are reported. These properties form the basis for additional investigations in thermal behavior of U-Mo fuel under high performance research reactor irradiation conditions. Measurements were performed on samples harvested from fuel plates irradiated under high fission power density and surface heat flux and complement previous measurements on samples subjected to moderate fission power density and surface heat flux. Specific heat capacity of irradiated monolithic U-Mo increases with increasing temperature and fission density, but carries large uncertainties associated with thickness measurements used to determine the mass fraction of the layer constituents for extraction of the U-Mo specific heat capacity, specifically the very thin and nonuniform Zr diffusion barrier. Density of irradiated monolithic U-Mo decreases with increasing fission density resulting from fission gas swelling and porosity formation. Thermal diffusivity of irradiated monolithic U-Mo increased with increasing temperature and decreased with increasing fission density. Thermal conductivity of irradiated monolithic U-Mo increased with increasing temperature, and in general, appeared to decrease and become less sensitive to temperature with increasing fission density. Thermal conductivity measurements compared to a semi-empirical model agreed within ±30%. It is suspected that the main driver in deviation between model calculations and measurements is the fission gas swelling determination, which does not account for fission power density or irradiation temperature.

uranium (U), molybdenum, nuclear fuel, thermal con↗

Defect cluster and nonequilibrium gas bubble associated growth in irradiated UMo fuels – a cluster dynamics and phase field model

Irradiation examination shows that gas bubble swelling kinetics is much faster after irradiation-induced recrystallization than that prior recrystallization in UMo fuels. It implies that gas bubbles in coarse grains and small recrystallized grains have different growth behavior. In this work, a phase-field model of gas bubble evolution integrating microstructure dependent cluster dynamics has been developed, for the first time, to study the gas bubble swelling behavior in the recrystallization zone of UMo fuels. Generation, diffusion, reaction, sink, emission and clustering of vacancies and interstitials are described by the cluster dynamics model while a phase-field model is used to describe the evolution of non-equilibrium gas bubbles including nucleation and growth. With the coupled model, the effect of defect generation rate, clustering rate, interstitial emission and sink rates on grain boundaries on the gas bubble evolution are systematically simulated. A set of model parameters (defect generation rate, clustering rate, interstitial emission and sink rates) is determined by comparing measured and simulated gas bubble swelling kinetics. The results demonstrate that interstitial clustering is one of the important physical mechanisms which results in a fast gas bubble swelling kinetics in the recrystallization zone. The developed model can also be extended to study the associated growth of defect and second phase precipitates often observed in irradiated materials.

Hu, Shenyang↗

A Monte Carlo Model of Irradiation-Induced Recrystallization in Polycrystalline UMo Fuels

Experiments show that irradiation-induced recrystallization speeds up the swelling kinetics in U10wt%Mo fuels. However, recrystallization mechanisms and the effect of initial grain microstructures on recrystallization kinetics are still unclear. In this work a Monte Carlo model coupling the rate theory of defect evolution has been developed to study the irradiation-induced recrystallization. The rate theory is used to describe the spatial evolution of gas bubbles, interstitials and interstitial loops; First-Passage Kinetic Monte Carlo (FPKMC) approach is used to describe the fast and strongly anisotropic migration of interstitials, and a Cellular Automata method is used to model the formation of recrystallized grains. With the assumption that recrystallization may occur when the local interstitial loop density is larger than a given critical value, simulation results reveal that 1) recrystallized grains first nucleate on grain boundaries and the recrystallization zone front moves to the center of original coarse grains in the UMo matrix, and 2) recrystallization starts earlier in coarse polycrystalline structures, while the overall recrystallization kinetics decreases with increasing grain size. These results agree with experimental observations. The comparison of recrystallization kinetics obtained from experiments and modeling suggests that the interstitial loop accumulation leads to the recrystallization and the interstitial loop growth is suppressed inside coarse grains due to the over-pressured intra-granular gas bubbles.

Frazier, William E.↗

Nanoscale Spatially Resolved Mapping of Uranium Enrichment

Abstract Spatially resolved analysis of uranium (U) isotopes in small volumes of actinide-bearing materials is critical for a variety of technical disciplines, including earth and planetary sciences, environmental monitoring, bioremediation, and the nuclear fuel cycle. However, achieving subnanometer-scale spatial resolution for such isotopic analysis is currently a challenge. By using atom probe tomography—a three-dimensional nanoscale characterisation technique—we demonstrate unprecedented nanoscale mapping of U isotopic enrichment with high sensitivity across various microstructural interfaces within small volumes (~100 nm 3 ) of depleted and low-enriched U alloyed with 10 wt% molybdenum that has different nominal enrichments of 0.20 and 19.75% 235 U, respectively. We map enrichment in various morphologies of a U carbide phase, the adjacent γ-UMo matrix, and across interfaces (e.g., carbide/matrix, grain boundary). Results indicate the U carbides were formed during casting, rather than retained from either highly enriched or depleted U feedstock materials. The approach presented here can be applied to study nanoscale variations of isotopic abundances in the broad class of actinide-bearing materials, providing unique insights into their origins and thermomechanical processing routes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Process Modeling of U-10wt% Mo Alloys Using Integrated Computational Materials Engineering

Low-enriched uranium alloyed with 10 wt% molybdenum (U-10Mo) has been identified as a promising alternative to highly enriched uranium as fuel for the nation’s high-performance research reactors. Manufacturing the U-10Mo alloy consists of multiple complex thermomechanical processes, which is highly challenging for computational modeling. The integrated computational materials engineering (ICME) concept supports building a microstructure-based framework to investigate the effect of manufacturing processes on the material microstructure. In this report, an ICME model that combines homogenization, hot rolling, annealing, and cold rolling is presented as an example of implementing the ICME concept for modeling the manufacturing processes of the U-10Mo alloy. The integrated model enables information to be passed between the different model components, leading to an improved prediction and a better understanding of microstructure across multiple processes. The integrated model was also implemented to investigate the variation of chemical composition, thickness of the zirconium interlayer, grain growth, and carbide redistribution and fracture of U-10Mo during the thermomechanical processes. With the homogenization model, a molybdenum concentration map can be reconstructed from any given microstructure, and the homogenization time needed to reach a desired homogenization level can also be approximated. The microstructure-based finite-element rolling model, shows that the homogenization process reduces the nonuniformity in the thickness of the zirconium interlayers on the U-10Mo. With the output from the rolling model, a statistical analysis of second-phase hard particles was conducted to quantify the particle redistribution and interparticle spacing between carbides during the deformation. Also, new stringer identification criteria were proposed to predict the correlation between stringer volume fractions and hot-rolling reduction. A macro-finite-element method hot-rolling model showed that higher reduction passes can be achieved within the mill separation force range, and a new “aggressive” rolling schedule was proposed. The model also showed the importance of can material on the quality of rolled foils, with stronger can materials resulting in hot-rolled U-10Mo free of defects (waviness, dog-boning). The deformation-induced recrystallization model demonstrated capability to use inputs from deformation simulations of strain accumulation in U-10Mo samples to predict grain growth behavior of the fuel during thermal treatment stages. Finally, a plane-strain compression mode simulated particle fracture and calculates the void volume fraction generated during cold rolling. The macro-finite-element method cold-rolling model showed that smaller diameter rolls are necessary to achieve the desired foil thickness.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A machine learning approach to thermal conductivity modeling: A case study on irradiated uranium-molybdenum nuclear fuels

A deep neural network was developed for the purpose of predicting thermal conductivity with a case study performed on irradiated nuclear fuel. Traditional thermal conductivity modeling approaches rely on existing theoretical frameworks that describe known, relevant phenomena that govern the microstructural evolution processes during neutron irradiation (such as recrystallization, and pore size, distribution and morphology). Current empirical modeling approaches, however, do not represent all irradiation test data well. We develop a machine learning approach to thermal conductivity modeling that does not require a priori knowledge of a specific material microstructure and system of interest. Our approach allows re-searchers to probe dependency of thermal conductivity on a variety of reactor operating and material conditions. The purpose of building such a model is to allow for improved predictive capabilities linking structure-property-processing-performance relationships in the system of interest (here, irradiated nuclear fuel), which could lead to improved experimental test planning and characterization. The uranium-molybdenum system is the fuel system studied in this work, and historic irradiation test data is leveraged for model development. Our model achieved a mean absolute percent error of approximately 10%. Results indicate our model generalizes well to never before seen data, and thus use of deep learning methods for material property predictions from limited, historic irradiation data is a viable approach. This work challenges the current paradigm in materials science, where material property models are based on limited experimental data fitted to low-dimensionality phenomenological models, or by simulations in which fundamental equations are explicitly solved. The work presented here aims to demonstrate the potential and limitations of machine learning in the field of materials science and material property modeling.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The Effect of Rolling As-Cast and Homogenized U-10Mo Samples on the Microstructure Development and Recovery Curves

Over the past several years Pacific Northwest National Laboratory (PNNL) has been actively involved in supporting the U.S. Department of Energy National Nuclear Security Administration Office of Material Management and Minimization (formerly Global Threat Reduction Initiative). The U.S. High- Power Research Reactor (USHPRR) project is developing alternatives to existing highly enriched uranium alloy fuel to reduce the proliferation threat. One option for a high-density metal fuel is uranium alloyed with 10 wt% molybdenum (U-10Mo). Forming the U-10Mo fuel plates/foils via rolling is an effective technique and is actively being pursued as part of the baseline manufacturing process. The processing of these fuel plates requires systematic investigation/understanding of the pre- and post-rolling microstructure, end-state mechanical properties, residual stresses, and defects, their effect on the mill during processing, and eventually, their in-reactor performance. In the work documented herein, studies were conducted to determine the effect of cold and hot rolling the as-cast and homogenized U-10Mo on its microstructure and hardness. The samples were homogenized at 900°C for 48 h, then later annealed for several durations and temperatures to investigate the effect on the material’s microstructure and hardness. The rolling of the as-cast plate, both hot and cold, was observed to form a molybdenum-rich and -lean banded structure. The cold rolling was ineffective, and in some cases exacerbated the as-cast defects. The grains elongated along the rolling direction and formed a pancake shape, while the carbides fractured perpendicularly to the rolling direction and left porosity between fractured particles of UC. The subsequent annealing of these samples at sub-eutectoid temperatures led to rapid precipitation of the ' lamellar phase, mainly in the molybdenum-lean regions. Annealing the samples above the eutectoid temperature did not refine the grain size or the banded microstructure. However, annealing the samples led to quick recovery in hardness as evidenced by a drop in Vickers hardness of 20%. Hot rolling was performed at 650 and 800°C. The hot-rolling mill loads (load separation force) were approximately 40 to 50% less than the cold-rolling for the same reduction and thickness. It was observed that hot rolling the samples with 50% or more reduction in thickness were responsible for dynamic recrystallization in the hot-rolled samples and led to grain refinement. Unlike the cold-rolled samples, the hot-rolled samples did not fracture the carbides and appeared to heal the casting defects. The recovery phenomenon was similar to the cold-rolled samples above the eutectoid temperatures, but owing to the refined grain size, the precipitation of the lamellar phase was far more rapid in these samples and the hardness increased more rapidly than in the cold rolled sample when heated below the eutectoid temperature. The data generated from these rolling efforts has been used to make the process modeling efforts more robust and applicable to all USHPRR partner rolling mills. The flow stress for cold rolling the samples was determined to be between 170-190 ksi, with frictional forces between 0.2 and 0.4 for the PNNL mill. The measured roll separation forces and those simulated using finite element methods for hot and cold rolling for the PNNL rolling mill were in good agreement.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

U-10Mo/Zr Interface Modeling using a Microstructure-Based FEM Approach

The U-10Mo in low enrichments (LEU) has been identified as the most promising alternative to the current highly enriched uranium (HEU) used in the United States’ fleet of high performance research reactors (USHPRRs). The nominal configuration of the new LEU U-10Mo plate fuel comprises a U-10Mo fuel foil enriched to slightly less than 20% U-235 (0.08” to 0.02” thick), a thin Zr interlayer/diffusion barrier (25 m thick) and a relatively thick outer can of 6061 aluminum. Currently, the Zr interlayer is clad by hot roll bonding. Previous studies and observations revealed a thinning of the zirconium (Zr) layer during this fuel fabrication process, which is not desirable from the fuel performance perspective. Coarse UMo grains, dendritic structures, Mo concentration segregation, carbides, and porosity are present in the as-cast material and can lead to a nonuniform UMo/Zr interface. The purpose of the current work is to investigate the effects of these microstructural parameters on the Zr coating variation. A microstructure-based finite-element method model was used in this work, and a study on the effect of homogenization on the interface between U-10Mo and Zr was conducted. The model uses actual backscattered electron–scanning electron microscopy microstructures, Mo concentrations, and mechanical properties to predict the behavior of a representative volume element under compressive loading during the rolling process. The model successfully predicted the experimentally observed thinning of the Zr layer in the as-cast material. The model also uses results from a homogenization model as an input, and a study on the effect of different levels of homogenization on the interface indicated that homogenization helps decrease this thinning. This model can be considered a predictive tool representing a first step for model integration and an input into a larger fuel fabrication performance model.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Rolling Process Modeling Report. Finite-Element Model Validation and Parametric Study on various Rolling Process parameters

Pacific Northwest National Laboratory (PNNL) has been investigating manufacturing processes for the uranium-10% molybdenum alloy plate-type fuel for high-performance research reactors in the United States. This work supports the U.S. Department of Energy National Nuclear Security Administration’s Office of Material Management and Minimization Reactor Conversion Program. This report documents modeling results of PNNL’s efforts to perform finite-element simulations to predict roll-separating forces for various rolling mill geometries for PNNL, Babcock & Wilcox Co., Y-12 National Security Complex, Los Alamos National Laboratory, and Idaho National Laboratory. The model developed and presented in a previous report has been subjected to further validation study using new sets of experimental data generated from a rolling mill at PNNL. Simulation results of both hot rolling and cold rolling of uranium-10% molybdenum coupons have been compared with experimental results. The model was used to predict roll-separating forces at different temperatures and reductions for five rolling mills within the National Nuclear Security Administration Fuel Fabrication Capability project. This report also presents initial results of a finite-element model microstructure-based approach to study the surface roughness at the interface between zirconium and uranium-10% molybdenum.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The Thermal Properties of Fresh and Spent U-Mo Fuels: An Overview

The evolution of the thermal conductivity of research reactor fuel during in-pile irradiation plays a significant role for the performance of the fuel element. To correctly simulate the heat fluxes and temperatures in the fuel meat during normal reactor operation and also off-normal scenarios, it is crucial to investigate the change in thermal properties, especially on the thermal conductivity, depending on the fission density and temperature. Two different U-Mo fuel types, dispersion and monolithic design, have to be considered. The thermal conductivity of fresh dispersion fuel lies between 40 and 80 W/mK depending on the particle shape, matrix material composition and U-loading. In contrast, the thermal conductivity of non-irradiated monolithic fuel is already below 15 W/mK due to the lack of the highly conductive aluminum matrix. The thermal conductivity is a composition of the thermal diffusivity, specific heat capacity and density. The specific heat capacity does not change significantly during irradiation. The density decreases slightly due to the formation of fission gas bubbles. The thermal diffusivity is strongly dependent on the materials structure. During irradiation this structure is destroyed by the fission products and fission gas bubbles. This decreases the thermal diffusivity of the irradiated material drastically down to 20% of the fresh material and has therefore the highest impact on the change of the thermal conductivity during irradiation. Therefore, during irradiation, the thermal conductivity of the dispersion fuel strongly deceases down to about 15% of the original value. The measurement of a dispersion segment from AFIP-1 with a burn-up of 6·1021f/cc yielded a thermal conductivity of 7 W/mK. The low thermal conductivity of monolithic fuel further decreases as well with increasing burn-up. At a burn-up of 3·1021f/cc, the thermal conductivity is already below 10 W/mK.

Uranium-Molybdenum, Thermal Properties, Nuclear Fu↗