Search NASA⌕ Search

Engineering topics

Burns, J. R.

Publications and source records attributed to Burns, J. R..

Transformational challenge reactor design characteristics

The Transformational Challenge Reactor (TCR) program was conceived with the goal to reduce costs and time frames associated with advanced reactor deployment by leveraging developments in advanced manufacturing, advanced materials, data science, and rapid prototyping and testing. The final deliverable of the TCR program was to be an operational test of a novel reactor design. The TCR core design incorporates a dense tri-structural-isotropic/SiC fuel form and volumetrically efficient yttrium hydride moderator, both of which were manufactured and characterized under the TCR program. The TCR is a 3 MW{sub th} He-cooled experimental nuclear reactor designed to reach a total integrated burnup of less than 24 effective full-power hours to keep the radioactive source term to a very low level. TCR design process revealed a positive moderator coefficient; however, the negative doppler coefficients for the fuel and thermal expansion of fuel, moderator, and core support plate yield an overall negative reactivity coefficient. Calculated fuel element temperatures and stresses are well within safety margins. The maximum hypothetical accident (i.e., de-pressurized loss of forced cooling) yields only a modest increase in reactor temperatures that are all within safety margins. This paper summarizes the high-level TCR design characteristics, which were derived from neutronics, thermohydraulics, thermomechanics, and safety analyses.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Depletion Analysis of Additively Manufactured Control Elements in HFIR

The High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory is a flux-trap type research reactor which provides one of the highest steady-state neutron sources in the world. HFIR neutrons are used for a range of research applications, including scattering experiments, materials irradiation, and isotope production. The HFIR core operates at 85 MW and is light water cooled and moderated. The core consists of several concentric cylindrical regions, as depicted in Fig. 1. At the center of the core is the flux trap, where the thermal flux reaches a maximum on the order of 10{sup 15} neutrons/cm{sup 2}-s. Immediately surrounding the flux trap are two annular fuel elements, an inner fuel element and an outer fuel element, each loaded with hundreds of thin fuel plates curved into an involute shape. Surrounding the outer fuel element are two thin control elements (CEs), an inner CE (ICE) and an outer CE (OCE). The CEs are axially zoned into three regions according to absorption strength: the white regions contain only structural aluminum and do not significantly contribute to absorption; the gray regions contain tantalum (Ta) as the primary absorber with a concentration of 30% by volume; and the black regions contain europium in the form of Eu{sub 2}O{sub 3} with a concentration of 33% by volume. A thick beryllium reflector is the final core component surrounding the CEs. A particular challenge to efficient maintenance and continued operation of HFIR is fabrication of the CEs, the current methods for which are tedious, outdated, and expensive. In an effort to improve the operational economics of HFIR and to demonstrate the application of advanced manufacturing techniques to the production of nuclear reactor components, the ultrasonic additive manufacturing (UAM) process is being investigated for fabrication of the HFIR CEs. This application of UAM involves directly embedding small cylindrical compacts (∼5.6 mm diameter, ∼1.7 mm thick) containing 60% neutron poison by volume into an aluminum matrix, using energy from ultrasonic vibrations to bond the compacts to the aluminum. The CEs contain discrete regions of absorbing material, in contrast to the standard design with homogeneously distributed absorbers. This novel design necessitates an investigation into how the HFIR core neutronic behavior differs from the case with homogeneous CEs so as to ascertain the feasibility of using additively manufactured CEs in HFIR. From an operations perspective, it is desirable for the discrete CEs to match the performance of the homogeneous CEs as closely as possible so as to avoid reconsideration of established safety margins. Earlier analyses of HFIR under beginning of cycle (BOC) conditions have indicated that although absorption properties on a local scale differ significantly between CE designs, the macroscopic behavior (neutron multiplication and flux and power distributions) of the HFIR core is not significantly altered. This study now addresses CE performance throughout depletion of the HFIR core during a reactor cycle. These analyses help to construct a more complete picture of the feasibility of employing additively manufactured CEs in HFIR and will reveal any adjustments which must be made to the design in order to maintain acceptable performance. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A Comparison of Modeling Strategies for Additively Manufactured HFIR Control Elements

The High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory is a flux-trap type research reactor that is used for a range of research applications, including neutron scattering experiments, materials irradiation tests, and isotope production. The HFIR core comprises several concentric cylindrical regions; starting from the core centerline and moving radially outwards, these are the flux trap target (FTT) region, the inner and outer fuel elements (IFE and OFE), the inner and outer control elements (ICE and OCE), and the reflector region. The control elements (CEs) are axially zoned into regions of differing absorption strength: the white regions contain only structural aluminum and do not significantly contribute to reactivity control; the gray regions contain tantalum as the primary absorber with a concentration of 38% by volume, and the black regions contain europia (Eu{sub 2}O{sub 3}) as the primary absorber with a concentration of 31% by volume. During operation, the CEs are withdrawn symmetrically in opposite directions from the core to remove the neutron absorbers from the core and maintain criticality. The current approach to fabrication of the HFIR CEs is tedious, outdated, and expensive. In an effort to improve the operational economics of HFIR and to demonstrate the feasibility of advanced manufacturing techniques for production of nuclear reactor components, novel methods for production of neutron-poison bearing aluminum structures have been initiated at ORNL. For this application, the ultrasonic additive manufacturing (UAM) process involves the use of 3D printing technology to construct small cylindrical compacts (0.559 cm in diameter and 0.171 cm in height) of aluminum mixed with neutron-absorbing material. The compacts contain 60% poison (Ta or Eu{sub 2}O{sub 3}) by volume. These compacts are then embedded into an aluminum matrix before formation into the cylindrical shape appropriate for use in HFIR. The CEs produced in this process therefore contain discrete regions of absorbing material, in contrast to the traditional design with homogeneously distributed absorbers. It is therefore of interest to investigate how the HFIR core behavior with discrete CEs differs from the case with homogeneous CEs with respect to some key reactor physics parameters. The primary objective of this study is to compare modeling strategies for the discrete CE design and examine differences in the core physics between the discrete and homogeneous CE designs as predicted by each model. Lessons learned from this investigation may then be used to inform the design process in future endeavors. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗