Engineering topics

Burns, Malcolm John

Publications and source records attributed to Burns, Malcolm John.

5 records

DOE OSTI2024

An exploration of anomalous electrical noise in shocked cyclotrimethylenetrinitramine (RDX)-based explosives

Gas gun shock experiments on cyclotrimethylenetrinitramine (RDX)-based explosive compositions that employ embedded gauge particle velocity tracers have noted a significant amount of electrical noise when compared to other explosive formulations. This paper reexamines previously published embedded gauge data on Cyclotols (60–80 wt. % RDX) to quantify the electromagnetic behavior of these materials. The primary observation is a fourfold increase in the electrical noise when Cyclotols are shocked above 4.22 ± 0.08 GPa. Electromagnetic gauge noise is also observed within particle velocity traces in reactive growth and off-Hugoniot shocks, although at higher pressures than the direct shock case, suggesting a temperature- or kinetically dependent transition. In all cases, the electrical noise disappears upon detonation. By comparing with the static high-pressure phase diagram of RDX, we interpret this change in electromagnetic behavior to be a change in the RDX crystal structure to a piezoelectric phase, although it is uncertain whether the γ or ε phase is responsible for the observed behavior.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2022

Shock initiation of low density polymer bonded explosive LX-14: A study of two morphologies

A series of six shock initiation experiments have been carried out on low density LX-14 powder in order to simulate a shock insult on the heavily damage polymer bonded explosive, LX-14. Two distinct morphologies were studied (tap density molding powder and machined swarf), both at the same density of 0.942 g/cm 3 , or 50.1% theoretical maximum density. The purpose of these experiments was to provide data to help make an assessment of the effects that damage has on the material sensitivity to a planar shock. This was achieved primarily by providing shock sensitivity data in the form of a Pop plot, and also reactants equation of state data, which aids in the determination of input conditions for both the experiments performed in this work and also future experiments of this material type. The experiments were of a cut-back format, consisting of four sample heights on each shot and diagnosed with optical velocimetry. The experiments were carried out at the Technical Area 40 Chamber 9 gas gun facility at the Los Alamos National Laboratory, where the LX-14 targets were subjected to Al 6061 and Oxygen Free High Conductivity copper impactors launched to velocities up to 2.14 km/s. Time corrected reactive growth wave profiles are presented in this paper along with the derivation of the following Hugoniot parameters for this explosive, where the molding powder and machine swarf are represented by the following linear equations, respectively, U s = 1.64 (±0.64)u p + 2.25 (±0.49) and U s = 0.87 (±.0.60)u p + 4.08 (±0.49). The results show that the steady increase in shock sensitivity with increasing void fraction reaches an inflection point beyond which the shock sensitivity begins to decease. This inflection point lies between 65% and 50% of the theoretical maximum density of the LX-14. In both cases, the damaged LX-14 was not as sensitive as expected, with a relative shock sensitivity of the molding powder being less than the pressed LX-14, and the machined swarf having a shock sensitivity that is comparable to pressed LX-14.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2021

Efficient connection of reactive shock wave profiles to reaction models

The future of energetic materials development, especially high-performance high explosives, demands new efficient and cost-effective experimental methods to understand the performance of new materials when only limited, development-scale quantities are available. Indeed, perhaps thousands of new molecules that have promising thermodynamic properties have been synthesized, only to be documented in the literature and never evaluated for their potential due to the cost of scaling up to produce quantities needed for traditional performance measurements.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Shock Initiation of PBX 9502: Material Lots 006 and 007 heated to 76 Celsius

Two shock initiation experiments have been carried out on PBX 9502 material Lots 006 and 007 heated to 76 Celsius. The purpose of these shots is to assess the reactant equation of state and shock-todetonation transition behavior relative to previously characterized lots of heated PBX 9502. PBX 9502 consists of 95% tri-amino-tri-nitro-benzene (TATB) and 5% Kel-F 800 (a copolymer derived from the monomers chlorotrifluorethylene (CTFE) and vinylidine fluoride) by weight. The experiments carried out at the TA-40 Chamber 9 gas gun facility were subject to shock pressures of 12.01 and 11.44 GPa for shots 2s-1129 and 2s-1130 respectively. These pressures resulted in run-to-detonation transitions of 7.91 and 8.73 mm from the impact plane. Unfortunately, due to a series of problems with the heating system the Lot 007 shot was subject to temperature cycling twice before the experiment was fired. The results do not indicate that this had any effect on the sensitivity of the explosive. In terms of shock sensitivity the Lot 006 and 007 PBX 9502 was found to be much less sensitive than the recycled lot 004 when heated to 76 Celsius. The data actually lies closer to the suit of ambient data on the Pop Plot.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Shock initiation of the HMX-based explosive PBX 9012: Experiments, uncertainty analysis, and unreacted equation-of-state

In this study, shock initiation experiments have been carried out on the polymer-bonded explosive PBX 9012 [nominally 90% octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazine (HMX), 10% vinylidene–hexafluoropropylene copolymer (Viton A) by weight] in order to provide calibration data for the explosive’s unreacted equation-of-state (EOS) and shock-to-detonation transition for reactive burn rate calibration. The input pressures covered the range of 1.86–4.43 GPa. This provided run-to-detonation depths ranging from > 22.3 mm for the lowest pressure shot to 4.91 mm at the highest pressure. The relative shock sensitivity of PBX 9012 is compared to other HMX-explosives in terms of the Pop-plot, showing that the studied explosive is more sensitive than other similar HMX-based counterparts (with notable exceptions). The uncertainty in the shock velocity determinations from the shock tracker measurements are also investigated, yielding new uncertainty measures in the generated Hugoniot data and run-to-detonation coordinates. Finally, the unreacted equation-of-state is determined using a linear U s – u p Mie–Grüneisen relation and the Davis reactants EOS analytical form, the latter being more suited for reactive burn modeling.

36 MATERIALS SCIENCE↗