Search NASA⌕ Search

Engineering topics

Buttrill, Carey S.

Publications and source records attributed to Buttrill, Carey S..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2002

Simulation Study of Impact of Aeroelastic Characteristics on Flying Qualities of a High Speed Civil Transport

A piloted simulation study conducted in NASA Langley Visual Motion Simulator addressed the impact of dynamic aero- servoelastic effects on flying qualities of a High Speed Civil Transport. The intent was to determine effectiveness of measures to reduce the impact of aircraft flexibility on piloting tasks. Potential solutions examined were increasing frequency of elastic modes through structural stiffening, increasing damping of elastic modes through active control, elimination of control effector excitation of the lowest frequency elastic modes, and elimination of visual cues associated with elastic modes. Six test pilots evaluated and performed simulated maneuver tasks, encountering incidents wherein cockpit vibrations due to elastic modes fed back into the control stick through involuntary vibrations of the pilots upper body and arm. Structural stiffening and compensation of the visual display were of little benefit in alleviating this impact, while increased damping and elimination of control effector excitation of the elastic modes both offered great improvements when applied in sufficient degree.

Raney, David L.↗
NASA NTRS1999

High Speed Civil Transport Aircraft Simulation: Reference-H Cycle 1, MATLAB Implementation

The mathematical model and associated code to simulate a high speed civil transport aircraft - the Boeing Reference H configuration - are described. The simulation was constructed in support of advanced control law research. In addition to providing time histories of the dynamic response, the code includes the capabilities for calculating trim solutions and for generating linear models. The simulation relies on the nonlinear, six-degree-of-freedom equations which govern the motion of a rigid aircraft in atmospheric flight. The 1962 Standard Atmosphere Tables are used along with a turbulence model to simulate the Earth atmosphere. The aircraft model has three parts - an aerodynamic model, an engine model, and a mass model. These models use the data from the Boeing Reference H cycle 1 simulation data base. Models for the actuator dynamics, landing gear, and flight control system are not included in this aircraft model. Dynamic responses generated by the nonlinear simulation are presented and compared with results generated from alternate simulations at Boeing Commercial Aircraft Company and NASA Langley Research Center. Also, dynamic responses generated using linear models are presented and compared with dynamic responses generated using the nonlinear simulation.

Sotack, Robert A.↗
NASA NTRS1993

NASA LaRC Workshop on Guidance, Navigation, Controls, and Dynamics for Atmospheric Flight, 1993

This publication is a collection of materials presented at a NASA workshop on guidance, navigation, controls, and dynamics (GNC&D) for atmospheric flight. The workshop was held at the NASA Langley Research Center on March 18-19, 1993. The workshop presentations describe the status of current research in the GNC&D area at Langley over a broad spectrum of research branches. The workshop was organized in eight sessions: overviews, general, controls, military aircraft, dynamics, guidance, systems, and a panel discussion. A highlight of the workshop was the panel discussion which addressed the following issue: 'Direction of guidance, navigation, and controls research to ensure U.S. competitiveness and leadership in aerospace technologies.'

Buttrill, Carey S.↗
NASA NTRS1992

Modeling and model simplification of aeroelastic vehicles: An overview

The rigid-body degrees of freedom and elastic degrees of freedom of aeroelastic vehicles are typically treated separately in dynamic analysis. Such a decoupling, however, is not always justified and modeling assumptions that imply decoupling must be used with caution. The frequency separation between the rigid-body and elastic degrees of freedom for advanced aircraft may no longer be sufficient to permit the typical treatment of the vehicle dynamics. Integrated, elastic vehicle models must be developed initially and simplified in a manner appropriate to and consistent with the intended application. This paper summarizes key results from past research aimed at developing and implementing integrated aeroelastic vehicle models for flight controls analysis and design. Three major areas will be addressed: (1) the accurate representation of the dynamics of aeroelastic vehicles, (2) properties of several model simplification methods, and (3) the importance of understanding the physics of the system being modeled and of having a model which exposes the underlying physical causes for critical dynamic characteristics.

Waszak, Martin R.↗
NASA NTRS1992

Space robotics: Recent accomplishments and opportunities for future research

The Langley Guidance, Navigation, and Control Technical Committee (GNCTC) was one of six technical committees created in 1991 by the Chief Scientist, Dr. Michael F. Card. During the kickoff meeting Dr. Card charged the chairmen to: (1) establish a cross-Center committee; (2) support at least one workshop in a selected discipline; and (3) prepare a technical paper on recent accomplishments in the discipline and on opportunities for future research. The Guidance, Navigation, and Control Committee was formed and selected for focus on the discipline of Space robotics. This report is a summary of the committee's assessment of recent accomplishments and opportunities for future research. The report is organized as follows. First is an overview of the data sources used by the committee. Next is a description of technical needs identified by the committee followed by recent accomplishments. Opportunities for future research ends the main body of the report. It includes the primary recommendation of the committee that NASA establish a national space facility for the development of space automation and robotics, one element of which is a telerobotic research platform in space. References 1 and 2 are the proceedings of two workshops sponsored by the committee during its June 1991, through May 1992 term. The focus of the committee for the June 1992 - May 1993 term will be to further define to the recommended platform in space and to add an additional discipline which includes aircraft related GN&C issues. To the latter end members performing aircraft related research will be added to the committee. (A preliminary assessment of future opportunities in aircraft-related GN&C research has been included as appendix A.)

Montgomery, Raymond C.↗
NASA NTRS1992

Simulation model of a twin-tail, high performance airplane

The mathematical model and associated computer program to simulate a twin-tailed high performance fighter airplane (McDonnell Douglas F/A-18) are described. The simulation program is written in the Advanced Continuous Simulation Language. The simulation math model includes the nonlinear six degree-of-freedom rigid-body equations, an engine model, sensors, and first order actuators with rate and position limiting. A simplified form of the F/A-18 digital control laws (version 8.3.3) are implemented. The simulated control law includes only inner loop augmentation in the up and away flight mode. The aerodynamic forces and moments are calculated from a wind-tunnel-derived database using table look-ups with linear interpolation. The aerodynamic database has an angle-of-attack range of -10 to +90 and a sideslip range of -20 to +20 degrees. The effects of elastic deformation are incorporated in a quasi-static-elastic manner. Elastic degrees of freedom are not actively simulated. In the engine model, the throttle-commanded steady-state thrust level and the dynamic response characteristics of the engine are based on airflow rate as determined from a table look-up. Afterburner dynamics are switched in at a threshold based on the engine airflow and commanded thrust.

Buttrill, Carey S.↗
NASA NTRS1991

Design of an active flutter suppression system for the Active Flexible Wing

The design of an active flutter suppression controller and wind tunnel validation test results are presented. This controller, designed using Nyquist methods and traditional root locus, is applied to the Active Flexible Wing (AFW) wind tunnel model. Wind tunnel tests were conducted to validate the design and demonstrate flutter suppression at a fixed altitude while performing aggressive rolling maneuvers representative of high-performance military aircraft. The controller succeeded in simultaneous suppression of two distinct flutter modes by significantly increasing the flutter dynamic pressure in spite of errors in the mathematical model.

Waszak, Martin R.↗
NASA NTRS1991

Development, simulation validation, and wind tunnel testing of a digital controller system for flutter suppression

Flutter suppression (FS) is one of the active control concepts being investigated by the AFW program. The design goal for FS control laws was to increase the passive flutter dynamic pressure by 30 percent. In order to meet this goal, the FS control laws had to be capable of suppressing both symmetric and antisymmetric flutter instabilities simultaneously. In addition, the FS control laws had to be practical and low-order, robust and capable of real time execution within the 200 hz. sampling time. The purpose here is to present an overview of the development, simulation validation, and wind tunnel testing of a digital controller system for flutter suppression.

Hoadley, Sherwood Tiffany↗
NASA NTRS1991

Model order reduction applied to a hot-bench simulation of an aeroelastic wind-tunnel model

Simulations of an aeroelastically scaled wind-tunnel model were developed for hot-bench testing of a digital controller. The digital controller provided active flutter-suppression, rolling-maneuver-load alleviation, and plant estimation. To achieve an acceptable time scale for the hot-bench application, the mathematical model of the wind-tunnel model was reduced from 220 states to approximately 130 states while assuring that the required accuracy was preserved for all combinations of 10 inputs and 56 outputs. The reduction was achieved by focussing on a linear, aeroelastic submodel of the full mathematical model and by applying a method based on the internally balanced realization of a dynamic system. The error-bound properties of the internally balanced realization significantly contribute to its utility in the model reduction process. The reduction method and the results achieved are described.

Buttrill, Carey S.↗
NASA NTRS1990

Hot-bench simulation of the active flexible wing wind-tunnel model

Two simulations, one batch and one real-time, of an aeroelastically-scaled wind-tunnel model were developed. The wind-tunnel model was a full-span, free-to-roll model of an advanced fighter concept. The batch simulation was used to generate and verify the real-time simulation and to test candidate control laws prior to implementation. The real-time simulation supported hot-bench testing of a digital controller, which was developed to actively control the elastic deformation of the wind-tunnel model. Time scaling was required for hot-bench testing. The wind-tunnel model, the mathematical models for the simulations, the techniques employed to reduce the hot-bench time-scale factors, and the verification procedures are described.

Buttrill, Carey S.↗
NASA NTRS1990

Digital-flutter-suppression-system investigations for the active flexible wing wind-tunnel model

Active flutter suppression control laws were designed, implemented, and tested on an aeroelastically-scaled wind tunnel model in the NASA Langley Transonic Dynamics Tunnel. One of the control laws was successful in stabilizing the model while the dynamic pressure was increased to 24 percent greater than the measured open-loop flutter boundary. Other accomplishments included the design, implementation, and successful operation of a one-of-a-kind digital controller, the design and use of two simulation methods to support the project, and the development and successful use of a methodology for on-line controller performance evaluation.

Perry, Boyd, III↗
NASA NTRS1990

Digital-flutter-suppression-system investigations for the active flexible wing wind-tunnel model

Active flutter suppression control laws were designed, implemented, and tested on an aeroelastically-scaled wind-tunnel model in the NASA Langley Transonic Dynamics Tunnel. One of the control laws was successful in stabilizing the model while the dynamic pressure was increased to 24 percent greater than the measured open-loop flutter boundary. Other accomplishments included the design, implementation, and successful operation of a one-of-a-kind digital controller, the design and use of two simulation methods to support the project, and the development and successful use of a methodology for online controller performance evaluation.

Perry, Boyd, III↗
NASA NTRS1990

Hot-bench simulation of the active flexible wing wind-tunnel model

Two simulations, one batch and one real-time, of an aeroelastically-scaled wind-tunnel model were developed. The wind-tunnel model was a full-span, free-to-roll model of an advanced fighter concept. The batch simulation was used to generate and verify the real-time simulation and to test candidate control laws prior to implementation. The real-time simulation supported hot-bench testing of a digital controller, which was developed to actively control the elastic deformation of the wind tunnel model. Time scaling was required for hot-bench testing. The wind-tunnel model, the math models for the simulations, the techniques employed to reduce the hot-bench time-scale factor, and the verification procedures are described.

Buttrill, Carey S.↗
NASA NTRS1990

Design, implementation, simulation, and testing of digital flutter suppression systems for the active flexible wing wind-tunnel model

Active flutter suppression control laws were designed, implemented, and tested on an aeroelastically-scaled wind-tunnel model in the NASA Langley Transonic Dynamics Tunnel. One of the control laws was successful in stabilizing the model while the dynamic pressure was increased to 24 percent greater than the measured open-loop flutter boundary. Other accomplishments included the design, implementation, and successful operation of a one-of-a-kind digital controller, the design and use of two simulation methods to support the projet, and the development and successful use of a methodology for online controller performance evaluation.

Perry, Boyd, III↗
NASA NTRS1990

Modeling and model simplification of aeroelastic vehicles

The rigid-body degrees of freedom and elastic degrees of freedom of aeroelastic vehicles are typically treated separately in dynamic analysis. Such a decoupling, however, is not always justified and modeling assumptions that imply decoupling must be used with caution. The frequency separation between the rigid-body and elastic degrees of freedom for advanced aircraft may no longer be sufficient to permit the typical treatment of the vehicle dynamics. Integrated, elastic vehicle models must be developed initially and simplified in a manner appropriate to and consistent with the intended application. This paper summarizes key results from the research aimed at developing and implementing integrated aeroelastic vehicle models for flight controls analysis and design. Three major areas will be addressed: (1) the accurate representation of the dynamics of aeroelastic vehicles, (2) properties of several model simplification methods, and (3) the importance of understanding the physics of the system being modeled and of having a model which exposes the underlying physical causes for critical dynamic characteristics.

Waszak, Martin R.↗
NASA NTRS1989

Aeroservoelastic wind-tunnel investigations using the Active Flexible Wing Model: Status and recent accomplishments

The status of the joint NASA/Rockwell Active Flexible Wing Wind-Tunnel Test Program is described. The objectives are to develop and validate the analysis, design, and test methodologies required to apply multifunction active control technology for improving aircraft performance and stability. Major tasks include designing digital multi-input/multi-output flutter-suppression and rolling-maneuver-load alleviation concepts for a flexible full-span wind-tunnel model, obtaining an experimental data base for the basic model and each control concept and providing comparisons between experimental and analytical results to validate the methodologies. The opportunity is provided to improve real-time simulation techniques and to gain practical experience with digital control law implementation procedures.

Noll, Thomas E.↗
NASA NTRS1989

Results of including geometric nonlinearities in an aeroelastic model of an F/A-18

An integrated, nonlinear simulation model suitable for aeroelastic modeling of fixed-wing aircraft has been developed. While the author realizes that the subject of modeling rotating, elastic structures is not closed, it is believed that the equations of motion developed and applied herein are correct to second order and are suitable for use with typical aircraft structures. The equations are not suitable for large elastic deformation. In addition, the modeling framework generalizes both the methods and terminology of non-linear rigid-body airplane simulation and traditional linear aeroelastic modeling. Concerning the importance of angular/elastic inertial coupling in the dynamic analysis of fixed-wing aircraft, the following may be said. The rigorous inclusion of said coupling is not without peril and must be approached with care. In keeping with the same engineering judgment that guided the development of the traditional aeroelastic equations, the effect of non-linear inertial effects for most airplane applications is expected to be small. A parameter does not tell the whole story, however, and modes flagged by the parameter as significant also need to be checked to see if the coupling is not a one-way path, i.e., the inertially affected modes can influence other modes.

Buttrill, Carey S.↗