Search NASA⌕ Search

Engineering topics

Cady, Carl M

Publications and source records attributed to Cady, Carl M.

At least 19 records

Characterization of Shocked Beryllium

Beryllium metal has many excellent structural properties in addition to its unique radiation characteristics, including: high elastic modulus, low Poisson's ratio, low density, and high melting point. However, it suffers from several major mechanical drawbacks: 1) high anisotropy - due to its hexagonal lattice structure and its susceptibility to crystallographic texturing; 2) susceptibility to impurity-induced fracture - due to grain boundary segregation; and 3) low intrinsic ductility at ambient temperatures thereby limiting fabricability. While large ductility results from deformation under the conditions of compression, the material can exhibit a brittle behavior under tension. Furthermore, there is a brittle to ductile transition at approximately 200 C under tensile conditions. While numerous studies have investigated the low-strain-rate constitutive response of beryllium, the combined influence of high strain rate and temperature on the mechanical behavior and microstructure of beryllium has received limited attention over the last 40 years. Prior studies have focused on tensile loading behavior, or limited conditions of dynamic strain rate and/or temperature. The beryllium used in this study was Grade S200-F (Brush Wellman, Inc., Elmore, OH) material. The work focused on high strain rate deformation and examine the validity of constitutive models in deformation rate regimes, including shock, the experiments were modeled using a Lagrangian hydrocode. Two constitutive strength (plasticity) models, the Preston-Tonks-Wallace (PTW) and Mechanical Threshold Stress (MTS) models, were calibrated using the same set of quasi-static and Hopkinson bar data taken at temperatures from 77K to 873K and strain rates from 0.001/sec to 4300/sec. In spite of being calibrated on the same data, the two models give noticeably different results when compared with the measured wave profiles. These high strain rate tests were conducted using both explosive drive and a gas gun to accelerate the material. Preliminary analysis of the results appears to indicate that, if fractured by the initial shock loading, the S200F Be remains sufficiently intact to support a shear stress following partial release and subsequent shock re-loading of the material. Additional 'arrested' drive shots were designed and tested to minimize the reflected tensile pulse in the sample. These tests were done to both validate the model and to put large shock induced compressive loads into the beryllium sample.

36 MATERIALS SCIENCE↗

Large-Strain Time-Temperature Equivalence and Adiabatic Heating of Polyethylene

Time-temperature equivalence is a well-known phenomenon in time-dependent material response, where rapid events at a moderate temperature are indistinguishable from some occurring at modest rates but elevated temperatures. However, there is as-yet little elucidation of how well this equivalence holds for substantial plastic strains. In this work, we demonstrate time-temperature equivalence over a large range in a previously studied high-density polyethylene formulation (HDPE). At strain-rates exceeding 0.1/s, adiabatic heating confounds the comparison of nominally isothermal material response, apparently violating time-temperature equivalence. Strain-rate jumps can be employed to access the instantaneous true strain rate without heating. Adiabatic heating effects were isolated by comparing a locus of isothermal instantaneous flow stress measurements from strain-rate jumps up to 1/s with the predicted equivalent states at 0.01/s and 0.001/s in compression. Excellent agreement between the isothermal jump condition locus and the quasi-static tests was observed up to 50% strain, yielding one effective isothermal plastic response for each material for a given time-temperature equivalent state. These results imply that time-temperature equivalence can be effectively used to predict the deformation response of polymers during extreme mechanical events (large strain and high strain-rate) from measurements taken at reduced temperatures and nominal strain-rates in the laboratory.

36 MATERIALS SCIENCE↗

Dynamic and quasi-static measurements of C-4 and primasheet P1000 explosives

We have measured dynamic and quasi-static mechanical properties of C-4 and Primasheet P1000 explosive materials to provide input data for modeling efforts. Primasheet P1000 is a pentaerythritol tetranitrate-based rubberized explosive. C-4 is a RDX-based moldable explosive. Dynamic measurements included acoustic and split-Hopkinson pressure bar tests. Quasi-static testing was done in compression on load frames and on a dynamic mechanical analyzer. Split-Hopkinson and quasi-static tests were done at five temperatures from -50 C to 50 C. Acoustic velocities were measured at, above, and below room temperature.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

On the quantitative measurement of fracture toughness in high explosive and mock materials

Two approaches in measuring the fracture toughness of heterogeneous high explosives and their mocks are explored in this investigation. One is the global measurement according to the ASTM E 1820-06 standard, which is primarily developed for metallic materials to obtain quantitative measurement of parameters such as the stress intensity factor, the J-integral, and the crack-tip opening displacement (CTOD). The second approach is based on local measurements using digital image correlation (DIC). Detailed results and comparisons of the two strategies will be presented for the Mock 900-21, a mechanical simulant of the PBX 9501 high explosive. Cracking is the most dominant mechanical failure mechanism in high explosives (HE) and a key parameter for describing and predicting crack initiation and extension is the fracture toughness. Quantitative measurement of such material property poses challenges, and this is mainly because that the material is highly heterogeneous with a very complicated microstructure and the contrast of the mechanical properties of the constituents is also remarkably high. In this investigation, we explore two strategies in measuring the fracture toughness of heterogeneous high explosives and their mocks. The first approach is based on the global measurement according to the ASTM E 1820-06 standard, which is primarily developed for metallic materials to obtain quantitative measurement of parameters such as the stress intensity factor, the J-integral, and the crack-tip opening displacement (CTOD). However, there are difficulties in applying the ASTM standard on energetic solids that include identifying the moment of crack initiation and pinpointing exact crack length at each instant of time. The second approach is based on local measurements. We developed a technique for quantitatively identifying the location and extent of macroscopic cracks in heterogeneous high explosive and mock material. By combining such a technique with the displacement field measurement using digital image correlation (DIC), we can describe, in detail, the crack-opening displacement and crack-opening angle as function of crack length. These quantitative measurements are then combined with the fracture mechanics analysis for the determination of fracture toughness. While the ASTM standard imposes strict requirements on the specimen geometry, loading configuration, and the amount of crack growth, the strategy based on local measurement should be applicable to any sample shapes and loading conditions, thus makes it more suitable to energetic materials, where often the amount of material can be tested is the major constraint. Detailed results and comparisons of the two strategies will be presented for the Mock 900-21, a mechanical simulant of the PBX 9501 high explosive.

36 MATERIALS SCIENCE↗