Search NASA⌕ Search

Engineering topics

Cady, Carl M.

Publications and source records attributed to Cady, Carl M..

Compressive strength of the plastic-bonded explosive surrogate idoxuridine under quasistatic and dynamic compression

Inert simulant materials, or “mocks”, are often used as surrogates for plastic-bonded explosives (PBX) in non-detonative tests in order to mitigate hazards. Mocks should reproduce as many non-detonative properties of the explosive as possible, including structural behavior in a variety of thermal and mechanical environments. Recently, the molecular crystal idoxuridine (IDOX) has been identified as an ideal mock for the main component in the explosive polymer-matrix composite PBX 9501, and has performed favorably under quasistatic loading conditions. Here, in order to assess robustness over a range of mechanical environments, plastic-bonded IDOX was compression tested from 0.001/s to 2000/s strain rates and compared to PBX 9501 historical data. Plastic-bonded IDOX showed good agreement to PBX 9501 across these strain rates, justifying continued development and production as a mock.

Burch, Alexandra C.↗

Gamma radiation effects on siloxane-based additive manufactured structures

Siloxane-basedadditive manufactured structures prepared by the direct ink write (DIW) technology were exposed to ionizing irradiation in order to gauge radiolysis effects on structure-property relationships. These well-defined 3-D structures were subjected to moderate doses of gamma irradiation in an inert atmosphere and characterized by a suite of experimental methods. Changes in thermal, chemical, microstructure, and mechanical properties were then evaluated by DSC, TGA, FT-IR, mass spectroscopy, EPR, solvent swelling, SEM, and uniaxial compressive load techniques. Our results demonstrated that 3-D structures made from aromatic-free siloxane resins exhibited hardening after being exposed to gamma radiation. This effect was accompanied by gas evolution, decreasing in crystallization levels, decreasing in solvent swelling and damage to the microstructure. Furthermore, long-lived radiation-induced radicals were not detected by EPR methods. Our results are consistent with cross-link formation being the dominant degradation mechanism over chain scission reactions. On the other hand, 3-D structures made from high phenyl content siloxane resins showed little radiation damage as evidenced by low off gassing.

36 MATERIALS SCIENCE↗

Thermo-mechanical characterization of silicone foams

Cellular solids such as elastomeric foams are used in many structural applications to absorb and dissipate energy, due to their light weight (low density) and high energy absorption capability. In this paper we will discuss foams derived from S5370, a silicone foam formulation developed by Dow Corning. In the application presented, the foam is consolidated into a cushion component of constant thickness but variable density. A mechanical material model developed by Lewis (2013), predicts material response, in part, as a function of relative density. To determine the required parameters for this model we have obtained the mechanical response in compression for ambient, cold and hot temperatures. The variable density cushion provided samples sufficient samples so that the effect of sample initial density on the mechanical response could be studied. The mechanical response data showed extreme sensitivity to relative density. We also observed at strains corresponding to 1 MPa a linear relationship between strain and initial density for all temperatures. Samples taken from parts with a history of thermal cycling demonstrated a stiffening response that was a function of temperature, with the trend of more stiffness as temperature increased above ambient. This observation is in agreement with the entropic effects on the thermo-mechanical behavior of silicone polymers. In this study, we present the experimental methods necessary for the development of a material model, the testing protocol, analysis of test data, and a discussion of load (stress) and gap (strain) as a function of sample initial densities and temperatures

36 MATERIALS SCIENCE↗

Post-Cure Studies on Solid Silicone Elastomer: DC745U

DC745U is a silicone elastomer originally manufactured by Dow Corning under the name of Silastic® DC745U at their manufacturing facility in Kendaville, Indiana. Currently DC745U is available through Xiameter® or Dow Corning’s distributor R. D. Abbott Company. This silicone elastomer is used in numerous parts of weapon systems, including outer pressure pads, aft cap support in W80 and pressure pad in the B61. DC745U is a proprietary formulation and limited information about its composition and properties is provided to the customer. Thus, Los Alamos National Laboratory and Lawrence Livermore National Laboratory have performed a variety of characterization experiments on this material.

36 MATERIALS SCIENCE↗

Effect of Aging on Fracture Toughness: Using Digital Image Correlation on DAP and Seabreeze [Slides]

The primary reason for this investigation was to determine the most accurate means of measuring the effect of aging in these materials. Initial characterization was pursued to find the most sensitive, repeatable test that would have the least amount of scatter in the test results. Preliminary investigations let to the conclusion that the fracture toughness would likely be the property to show the greatest change in behavior for any intrinsic material property. Test configurations that were initially considered were tensile tests, 3 and 4 point bend tests, Brazil tests, Brazil tests with initial damage and finally a test geometry that is being called a ‘compression- fracture" test. The tensile test will continue to be done because it will be used to generate information about the Poisson's ratio, which can be used in simulations that would verify the test results presented in this report. The bend bar and Brazil test configurations were tried and determined to be unsuitable because they allowed for unstable crack growth in the materials. The result of these investigations on un-pedigreed materials leading to the selection and use of a test geometry that has subsequently been used on pedigreed materials is the focus of this presentation.

36 MATERIALS SCIENCE↗

Characterization of Depleted-Uranium Strength and Damage Behavior

The intent of this report is to document the status of our knowledge of the mechanical and damage behavior of Depleted Uranium(DU hereafter). This report briefly summaries the motivation of the experimental and modeling research conducted at Los Alamos National Laboratory(LANL) on DU since the early 1980’s and thereafter the current experimental data quantifying the strength and damage behavior of DU as a function of a number of experimental variables including processing, strain rate, temperature, stress state, and shock prestraining. The effect of shock prestraining on the structure-property response of DU is described and the effect on post-shock mechanical behavior of DU is discussed. The constitutive experimental data utilized to support the derivation of two constitutive strength (plasticity) models, the Preston-Tonks-Wallace (PTW) and Mechanical Threshold Stress (MTS) models, for both annealed and shock prestrained DU are detailed and the Taylor cylinder validation tests and finite-element modeling (FEM) utilized to validate these strength models is discussed. The similarities and differences in the PTW and MTS model descriptions for DU are discussed for both the annealed and shock prestrained conditions. Quasi-static tensile data as a function of triaxial constraint and spallation test data are described. An appendix additionally briefly describes low-pressure equation-of-state data for DU utilized to support the spallation experiments. The constitutive behavior of DU screw/bolt material is presented. The response of DU subjected to dynamic tensile extrusion testing as a function of temperature is also described. This integrated experimental technique is planned to provide an additional validation test in the future. The damage data as a function of triaxiality, tensile and spallation data, is thereafter utilized to support derivation of the Tensile Plasticity (TEPLA) damage model and simulations for comparison to the DU spallation data are presented. Finally, a discussion of future needs in the area of needed DU strength and damage research at LANL is presented to support the development of physically-based predictive strength and damage modeling capability.

36 MATERIALS SCIENCE↗

Characterization of the Mechanical Properties of DAP and Seabreeze

The primary reason for this investigation was to determine the most accurate means of measuring the effect of aging in these materials. Initial characterization was pursued to find the most sensitive, repeatable test that would have the least amount of scatter in the test results. Preliminary investigations let to the conclusion that the fracture toughness would likely be the property to show the greatest change in behavior for any intrinsic material property. Test configurations that were initially considered were tensile tests, 3 and 4 point bend tests, Brazil tests, Brazil tests with initial damage and finally a test geometry that is being called a “compression – fracture“ test. The tensile test will continue to be done because it will be used to generate information about the Poisson’s ratio, which can be used in simulations that would verify the test results presented in this report. The bend bar and Brazil test configurations were tried and determined to be unsuitable because they allowed for unstable crack growth in the materials. The result of these investigations on un-pedigreed materials leading to the selection and use of a test geometry that has subsequently been used on pedigreed materials is the focus of this report.

36 MATERIALS SCIENCE↗