Search NASA⌕ Search

Engineering topics

Cai, Mei

Publications and source records attributed to Cai, Mei.

31 records · Page 2

Hybrid Li-S pouch cell with a reinforced sulfide glass solid-state electrolyte film separator

Here, in this paper, sulfide glass electrolyte powder with a nominal composition of (Li 2 S) 60 (SiS 2 ) 28 (P 2 S 5 ) 12 is hot pressed at a 330°C and 12 MPa into separator films using non-woven fiberglass reinforcement. The reinforced separator films are 93% dense, bendable, and have an ionic conductivity of 0.7 mS/cm at room temperature. When integrated into hybrid Li-S coin cells with liquid electrolyte, these reinforced glass separators blocked the parasitic polysulfide shuttle sufficiently to enable reversible cycling without LiNO 3 co-salt. Furthermore, the scalability of the reinforced glass separator technology is demonstrated by assembling and testing a hybrid single-layer pouch cell.

25 ENERGY STORAGE↗

Cathode porosity is a missing key parameter to optimize lithium-sulfur battery energy density

While high sulfur loading has been pursued as a key parameter to build realistic high-energy lithium-sulfur batteries, less attention has been paid to the cathode porosity, which is much higher in sulfur/carbon composite cathodes than in traditional lithium-ion battery electrodes. For high-energy lithium-sulfur batteries, a dense electrode with low porosity is desired to minimize electrolyte intake, parasitic weight, and cost. Here we report the profound impact on the discharge polarization, reversible capacity, and cell cycling life of lithium-sulfur batteries by decreasing cathode porosities from 70 to 40%. According to the developed mechanism-based analytical model, we demonstrate that sulfur utilization is limited by the solubility of lithium-polysulfides and further conversion from lithium-polysulfides to Li2S is limited by the electronically accessible surface area of the carbon matrix. Finally, we predict an optimized cathode porosity to maximize the cell level volumetric energy density without sacrificing the sulfur utilization.

25 ENERGY STORAGE↗

Quantifying inactive lithium in lithium metal batteries

Lithium metal anodes offer high theoretical capacities (3,860 milliampere-hours per gram)1, but rechargeable batteries built with such anodes suffer from dendrite growth and low Coulombic efficiency (the ratio of charge output to charge input), preventing their commercial adoption. The formation of inactive (‘dead’) lithium— which consists of both (electro)chemically formed Li + compounds in the solid electrolyte interphase and electrically isolated unreacted metallic Li 0 —causes capacity loss and safety hazards. Quantitatively distinguishing between Li + in components of the solid electrolyte interphase and unreacted metallic Li 0 has not been possible, owing to the lack of effective diagnostic tools. Optical microscopy, in situ environmental transmission electron microscopy, X-ray microtomography and magnetic resonance imaging provide a morphological perspective with little chemical information. Nuclear magnetic resonance, X-ray photoelectron spectroscopy and cryogenic transmission electron microscopy can distinguish between Li + in the solid electrolyte interphase and metallic Li 0 , but their detection ranges are limited to surfaces or local regions. Here we establish the analytical method of titration gas chromatography to quantify the contribution of unreacted metallic Li 0 to the total amount of inactive lithium. We identify the unreacted metallic Li 0 , not the (electro)chemically formed Li + in the solid electrolyte interphase, as the dominant source of inactive lithium and capacity loss. By coupling the unreacted metallic Li 0 content to observations of its local microstructure and nanostructure by cryogenic electron microscopy (both scanning and transmission), we also establish the formation mechanism of inactive lithium in different types of electrolytes and determine the underlying cause of low Coulombic efficiency in plating and stripping (the charge and discharge processes, respectively, in a full cell) of lithium metal anodes. Here we propose strategies for making lithium plating and stripping more efficient so that lithium metal anodes can be used for next-generation high-energy batteries.

25 ENERGY STORAGE↗

Manipulation of an ionic and electronic conductive interface for highly-stable high-voltage cathodes

A stable and conductive interface is one of the decisive factors in manipulating the performance of high voltage LiNi 0.5 Mn 1.5 O 4 (LNMO) cathode for Li-ion batteries. Herein, a hybrid Li 3 PO 4 -TiO 2 coating layer is designed as an interfacial material via controllable atomic layer deposition (ALD) on LNMO. The coating acts not just as a physical barrier to prevent the side-reactions between cathode and electrolyte at high voltage, more importantly, the hybrid coating material improves both interfacial ionic and electronic conductivities to build facile Li-ion and electron diffusion pathways for LNMO. The optimized LNMO demonstrates improved rate capability and long-life stability. The capacity retention is 81.2% comparing with 47.4% of bare LNMO at 0.5C after 300 cycles. Detailed surface structural evolution is studied via X-ray absorption near edge spectroscopy and transmission electron microscopy. Furthermore, this work provides new insights of hybrid interfacial design via ALD and promotes novel electrode architectures for batteries.

25 ENERGY STORAGE↗

Silicon‐Based Anodes for Lithium‐Ion Batteries: From Fundamentals to Practical Applications

Abstract Silicon has been intensively studied as an anode material for lithium‐ion batteries (LIB) because of its exceptionally high specific capacity. However, silicon‐based anode materials usually suffer from large volume change during the charge and discharge process, leading to subsequent pulverization of silicon, loss of electric contact, and continuous side reactions. These transformations cause poor cycle life and hinder the wide commercialization of silicon for LIBs. The lithiation and delithiation behaviors, and the interphase reaction mechanisms, are progressively studied and understood. Various nanostructured silicon anodes are reported to exhibit both superior specific capacity and cycle life compared to commercial carbon‐based anodes. However, some practical issues with nanostructured silicon cannot be ignored, and must be addressed if it is to be widely used in commercial LIBs. This Review outlines major impactful work on silicon‐based anodes, and the most recent research directions in this field, specifically, the engineering of silicon architectures, the construction of silicon‐based composites, and other performance‐enhancement studies including electrolytes and binders. The burgeoning research efforts in the development of practical silicon electrodes, and full‐cell silicon‐based LIBs are specially stressed, which are key to the successful commercialization of silicon anodes, and large‐scale deployment of next‐generation high energy density LIBs.

Feng, Kun↗

Hierarchical nanostructured core-shell Sn@C nanoparticles embedded in graphene nanosheets: spectroscopic view and their application in lithium ion batteries

Hierarchical carbon encapsulated tin (Sn@C) embedded graphene nanosheet (GN) composites (Sn@C–GNs) have been successfully fabricated via a simple and scalable one-step chemical vapor deposition (CVD) procedure. The GN supported Sn@C core–shell structures consist of a crystalline tin core, which is thoroughly covered by a carbon shell and more interestingly, extra voids are present between the carbon shell and the tin core. Synchrotron spectroscopy confirms that the metallic tin core is free of oxidation and the existence of charge redistribution transfer from tin to the carbonaceous materials of the shell, facilitating their intimate contact by chemical bonding and resultant lattice variation. The hybrid electrodes of this material exhibit a highly stable and reversible capacity together with an excellent rate capability, which benefits from the improved electrochemical properties of tin provided by the protective carbon matrix, voids and the flexible GN matrices.

Wang, Dongniu↗

Inward Lithium-Ion Breathing of Hierarchically Porous Silicon Anodes

Silicon has been identified as one of the most promising candidates as anode for high performance lithium-ion batteries. The key challenge for Si anodes is the large volume change induced chemomechanical fracture and subsequent rapid capacity fading upon cyclic charge and discharge. Improving capacity retention thus critically relies on smart accommodation of the volume changes through nanoscale structural design. In this work, we report a novel fabrication method for hierarchically porous Si nanospheres (hp-SiNSs), which consist of a porous shell and a hollow core. Upon charge/discharge cycling, the hp-SiNSs accommodate the volume change through reversible inward expansion/contraction with negligible particle-level outward expansion. Our mechanics analysis revealed that such a unique volume-change accommodation mechanism is enabled by the much stiffer modulus of the lithiated layer than the unlithiated porous layer and the low flow stress of the porous structure. Such inward expansion shields the hp-SiNSs from fracture, opposite to the outward expansion in solid Si during lithiation. Lithium ion battery assembled with this new nanoporous material exhibits high capacity, high power, long cycle life and high coulombic efficiency, which is superior to the current commercial Si-based anode materials. We find the low cost synthesis approach reported here provides a new avenue for the rational design of hierarchically porous structures with unique materials properties.

25 ENERGY STORAGE↗

General Motors: Final Report for Hydrogen Storage Engineering Center of Excellence

As part of the HSECoE team, the GM team built system models and detailed transport models for on-board hydrogen storage systems using metal hydrides and adsorbent materials. Detailed transport models have been developed for both the metal hydride and adsorbent systems with a focus on optimization of heat exchanger designs with the objective of minimizing the heat exchanger mass. We also performed work in collaboration with our partners on storage media structuring and enhancement studies for the metal hydride and adsorbent materials. Since the hydrogen storage materials are generally characterized by low density and low thermal conductivity, we conducted experiments to form pellets and add thermal conductivity enhancers to the storage material, and to improve cycling stability and durability of the metal hydride and adsorbent materials. Refueling of a MOF-5 pellet with cryogenic hydrogen was studied by developing a detailed two-dimensional axisymmetric COMSOL® model of the process. The effects of pellet permeability, thermal conductivity, and thermal conductivity enhancers were investigated. Our key area of focus has been on designing and building a cryo-adsorption vessel for validation of cryo-adsorption models. The 3-L cryogenic tank was used to study the fast fill and discharge dynamics of a cryo-adsorbent storage system, both experimentally and numerically.

08 HYDROGEN↗