Engineering topics

Cakmak, Ercan

Publications and source records attributed to Cakmak, Ercan.

At least 37 records · Page 2

DOE OSTI2023

Structure and Anharmonicity of α- and β -Sb 2 O 3 at Low Temperature

Antimony oxides are important materials for catalysis and flame-retardant applications. The two most common phases, α-Sb 2 O 3 (senarmontite) and β-Sb 2 O 3 (valentinite), have been studied extensively. Specific focus has been placed recently on their lattice dynamics properties and how they relate to the α-β phase transformation and their potential anharmonicity. However, there has not been any direct investigation of anharmonicity in these systems, and a surprising lack of low-temperature structural information has prevented further study. Here, we report the powder neutron diffraction data of both phases of Sb 2 O 3 , as well as structural information. α-Sb 2 O 3 behaved as expected, but β-Sb 2 O 3 revealed a small region of zero thermal expansion along the c axis. Additionally, while the β phase matched well with reported atomic displacement parameters, the α phase displayed a marked deviation. This data will enable further investigations into these systems.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Microstructural diversity and digestion yields of select bituminous and subbituminous coals as raw material candidates for carbon fiber precursor production

Here, this work investigates the use of coals as raw materials for carbon fiber precursor production as a new alternative to coal utilization. Coal being a highly complex and heterogeneous material with different macerals and minerals complicates this task. Extensive microstructural characterization as well as preliminary digestion studies are performed on three bituminous coals (Herrin and Springfield from the Illinois Basin and the Blue Gem from the Central Appalachians) and one subbituminous coal from the Powder River Basin (Monarch), as raw material candidates. The subbituminous coal was richer in oxygen, lower in sulfur, and had a higher volatile matter yield. Microstructural investigations were performed using X-ray diffraction, X-ray/neutron computed tomography, scanning electron microscopy with energy dispersive spectroscopy, and petrology. Mild solvent extraction studies were conducted using creosote and decant oil as solvents in microreactors. The extraction yield was sensitive to temperature and time (350 to 450 °C between 30 and 120 mins.) for both creosote and decant oil digestions. While the Blue Gem coal had more desirable microstructural properties with less mineral content and cleaner macerals, it had the lowest coal conversion to quinoline soluble ‘liquid’ (of the bituminous coals). The lower coal conversion yield was hypothesized to be connected to the lack of FeS2 which could act as a catalyst when Fe is liberated from the structure under solvent extraction conditions. The Herrin and Springfield coals revealed similar microstructures and coal conversion efficiencies (higher than Blue Gem). These coals were the most promising candidates for further examination from this first approximations study. The subbituminous Monarch coal, however, was deemed less suitable due to poor coal conversion and less desirable microstructures. Additionally, the presented results with combined microstructural data from multiple length scales established a framework necessary for a first approximations study in this new coal utilization approach.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2023

Hardness Measurements and Interface Behavior of SiC-B 4 C-Si Multiple Phase Particulate Composites Made with Melt Infiltration and Additive Manufacturing

Reaction-bonded SiC-B 4 C-Si ceramic composites were binder jet 3D-printed and subsequently pressureless-melt-infiltrated with molten Si. The addition of B 4 C aided the Si infiltration to produce a highly dense composite. The microstructures and phases of these composites were examined. The measured hardness values of each constituent with Vickers and nanoindentation matched the bulk values, and the macro-hardness values with Knoop and spherical indentation represented the bulk, composite hardness values of all three phases together, which was close to a rule of mixtures value. For particulate-based composites, this is a significant finding. The interfacial bonds of SiC and Si were imaged using scanning transmission electron microscopy to view intimacy, whereas the crack propagation was examined with carefully placed indents. This work demonstrated that pressureless melt infiltration with a reactive particle provides a method to shape non-wetting reaction-bonded ceramic composites with limited shrinkage and high density and provides insights into the mechanical behavior with numerous indentation techniques.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Characterization of Porosity and Pore Accessibility of Vitrinite-Rich Bituminous and Subbituminous Coals by Small-Angle Neutron Scattering, Mercury Intrusion Porosimetry, and Low-Pressure N 2 Adsorption

Three bituminous and one subbituminous vitrinite-rich coals were characterized using small-angle neutron scattering with contrast matching, mercury intrusion porosimetry, and low-pressure N 2 adsorption techniques to quantify their porosity and pore accessibility in an effort to assess their solvent extractabilities, as a first approximation, for manufacturing useful end-products. The techniques revealed consistent results while complimenting one another. The total porosity was found to follow the coal rank with the lowest rank having the highest porosity within the studied coals. The amount of inaccessible pores was found to increase with rank for the bituminous coals studied here. Finally, the increase in the ease of accessibility and total porosity with decreasing rank suggested easier penetration of chemical reagents for solvent extraction, for example.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Additive Manufacturing of C/C-SiC Ceramic Matrix Composites by Automated Fiber Placement of Continuous Fiber Tow in Polymer with Pyrolysis and Reactive Silicon Melt Infiltration

An additive manufacturing process for fabricating ceramic matrix composites has been developed based on the C/C-SiC system. Automated fiber placement of the continuous carbon fibers in a polyether ether ketone matrix was performed to consolidate the carbon fibers into a printed preform. Pyrolysis was performed to convert the polymer matrix to porous carbon, and then Si was introduced by reactive melt infiltration to convert a portion of the carbon matrix to silicon carbide. The densities and microstructures were characterized after each step during the processing, and the mechanical properties were measured. The C/C-SiC composites exhibited a porosity of 10–20%, characteristic flexural strength of 234.91 MPa, and Weibull modulus of 3.21. The composites displayed toughness via a significant displacement to failure.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Opening twisted polymer chains for simultaneously high printability and battery fast-charge

Fast-charging is key to the widespread adoption of battery-based electric vehicles. However, improving fast-charging through architecture optimization is expensive. To reduce costs and expand to commercialization, we applied roll-to-roll screen printing technology to create channels and decrease the tortuosity of electrodes. For the first time, this work successfully opened twisted polymer chains within high-solid-content inks to improve their screen printability and battery performance of as-printed electrodes. With LiNi 0.6 Mn 0.2 Co 0.2 O 2 as active materials, the 60% solid content ink presents superior screen printability after opening the twisted binder chains. As-printed electrode exhibits 33% higher charge capacity at 6 C than printed electrode with chains twisted ink at mass loading of 6.5 mg/cm 2 . Furthermore, coarse-grained molecular dynamics simulations are performed to study the underlying mechanism systematically. In conclusion, the new ink preparation procedure provides a scalable, effective strategy for manufacturing screen-printable battery ink and promotes screen-printed electrode technology.

25 ENERGY STORAGE↗

DOE OSTI2022

Micromechanical aspects of deformation and failure of advanced Iron-Chromium-Aluminum alloys

Here this work investigates the micromechanical deformation and failure mechanisms of advanced FeCrAl alloys developed for use in nuclear reactors as cladding material. Three different FeCrAl alloys (82-X)Fe-13Cr-5Al-X (X=Nb, TiC, 0 for base alloy) were investigated both in their as-received and welded states. In-situ neutron diffraction with simultaneous digital image correlation was used to determine micromechanical deformation mechanisms not only as a function of elemental composition but also as a condition of state (as-received vs. welded). Ex-situ X-ray computed tomography was used on as-deformed samples to help determine the failure mechanisms and void initiation strains.

36 MATERIALS SCIENCE↗

DOE OSTI2022

In situ characterization of phase transformations in petroleum pitch by high temperature X-ray diffraction

The phase transformation from isotropic to mesophase of a petroleum-derived pitch was monitored by in situ X-ray diffraction at 410 °C. The kinetics of the transformation were characterized by monitoring the growth of a broad peak at 2θ~24° and could be described by Avrami’s equation. The volatilization of low molecular weight components originally present in the pitch, or produced during the condensation reaction, was assessed by thermal gravimetry analysis, following the same thermal history. Ex situ characterizations of the pitch precursor before and after thermal treatment provided insight into the evolution of the molecular structure associated with mesophase generation (optical polarized microscopy, molecular weight distribution by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry, X-ray photoelectron spectroscopy, Auger spectroscopy, and thermal stability). Here, this investigation demonstrates the value of using complementary in situ and ex situ experimental techniques to characterize complex mechanisms during the processing of organic materials.

02 PETROLEUM↗

DOE OSTI2022

On the efficacy of post-build thermomechanical treatments to improve properties of Zirconium fabricated using ultrasonic additive manufacturing

Here, hot-isostatic pressing has been applied to Zirconium plate fabricated using the ultrasonic additive manufacturing (UAM) technique to enhance interfacial bond quality. Specimens heated to 800 C for 1 h at 100 MPa pressure showed grain growth across many prior foil-to-foil interfaces, thereby increasing foil adhesion. In addition to the material softening induced by a loss of Hall-Petch strengthening, premature failure of specimens loaded parallel to the build direction was observed. Premature specimen failure was attributed to the local delamination at prior foil-to-foil boundaries where grain growth was pinned by Ti impurities introduced during the UAM process via the interaction between a Ti-alloy buffer foil and the welded Zr-foils underneath. In addition, the presence of Ti along select foil interfaces resulted in the nucleation and growth of secondary (Zr,Ti)(Fe,Cr) laves phases during higher-temperature thermomechanical processing. Using a combination of micro-scale X-ray computed tomography, fractography, and in-situ digital image correlation, the effect of defects along prior foil-to-foil boundaries was revealed as delamination-assisted plasticity accelerated specimen failure in preferred tensile orientations. These findings underscore the importance of impurity control when optimizing weld quality of higher-strength material systems using ultrasonic welding.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Leveraging computational thermodynamics to guide SiC-ZrC chemical vapor deposition process development

Here using the CALPHAD approach to understand zirconium carbide deposition, a series of phase equilibria were calculated from a custom thermodynamic database based on a literature source, and the equilibria were used to explore the potential chemical vapor deposition (CVD) processing space in the ZrCl 4 -CH 3 SiCl 3 -CH 4 -H 2 system as a function of pressure, temperature, and gas composition. Several gas ratios were considered. At a given ZrCl 4 :CH 3 SiCl 3 ratio within the range studied, the most important factor was found to be the ratios of CH 4 :ZrCl 4 , wherein the nature of the composition – carbide vs. silicide – could be controlled. A pure binary composition of ZrC and SiC is expected to form by increasing the initial amount of methane and decreasing the amount of hydrogen from values predicted purely based on thermodynamic equilibrium. Rietveld analysis of the x-ray diffractograms from corresponding experimental depositions confirmed that increasing the CH 4 :ZrCl 4 ratio increased the fraction of carbon-containing species (SiC, ZrC) and decreased the fraction of non-carbides (ZrSi, ZrSi 2 , etc.), as predicted from the CALPHAD results.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Multiscale characterization and comparison of historical and modern nuclear graphite grades

Beginning with Chicago Pile I, graphite has been used as a moderator material in nuclear power stations and is considered a potential material for use in future Generation IV advanced reactors. The microstructure of graphite is responsible for much of its mechanical and thermo-physical properties, and how it responds to irradiation. To understand graphite microstructure, it is necessary to understand its porosity at the macro- and micro-scales; and to understand its porosity, it is necessary to characterize the morphological connectivity of the void content and the two main phases of graphite: filler and binder. Here, using several microscopy and analytical techniques, a detailed examination of the heterogeneity, microstructure and pore structure of different graphite grades and their binder and filler phases is presented. Significant differences were found between coarser and finer nuclear grades. Coarse grades have a more diverse range of filler particles, pores and thermal cracks. Finer grades have a more well-defined pore size distribution, fewer variations of filler particles sizes and do not contain as many large thermal cracks. Fine grades tend to have a well-connected network of pores whereas coarser grades contain a larger content of closed porosity. The framework developed within this work can be applied and used to assess the various graphite grades that would down-select materials for specific use in graphite moderated reactor designs.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2022

Ultra-high gamma irradiation of calcium silicate hydrates: Impact on mechanical properties, nanostructure, and atomic environments

The concrete biological shield in a nuclear power plant receives ~100–200 MGy gamma dosage during an 80-year design life. However, precise changes in the mechanical properties and atomic environments of C-S-H at ultrahigh irradiation dosages have not been systematically documented. Here, we report that irradiation decreases C-S-H basal spacing (~ 0.6 ± 0.1 Å for 189 MGy) and increases its Young's modulus, which is attributed to the lower basal spacing as the nano porosity potentially increased and microporosity remained unchanged. Irradiation also decreased the molecular water content and increased hydroxyl groups in C-S-H, showing that interlayer water removal reduces the basal spacing. Finally, 1 H and 29 Si NMR results indicate some disorder in the local proton CaO-H species and slight depolymerization of the silicate structure. Together, these results indicate that the C-S-H gel stiffens upon ultrahigh gamma irradiation dosage, a finding which concerns long-term nuclear power plants operations worldwide.

1H NMR↗

DOE OSTI2022

Qualitative and quantitative analysis of neutron irradiation effects in SiC/SiC composites using X-ray computed tomography

Silicon carbide fiber-reinforced silicon carbide matrix (SiC/SiC) composites are candidate materials for cladding of light water reactor (LWR) fuels. Loss of fission product gas retention due to the formation of microcrack networks is considered a potential failure mechanism for SiC/SiC-cladded fuels. In this work, a variety of SiC/SiC composite tubes were irradiated with and without an LWR-relevant radial heat flux in the High Flux Isotope Reactor, followed by detailed characterization with X-ray computed tomography (XCT). This first set of XCT data for neutron-irradiated samples confirmed that the internal stresses arising from a combination of temperature gradients and irradiation-induced swelling act as the primary driver for cracking. Consequently, while the observed cracking patterns varied depending on the tube architectures, the sharp edges of relatively large pores were found to be the common stress concentrator. These findings are useful to help improve the design and manufacturing of SiC/SiC fuel claddings for reduced failure probability.

42 ENGINEERING↗

DOE OSTI2022

Interaction of beryllium with 316H stainless steel in molten Li 2 BeF 4 (FLiBe)

The increased demand in renewable energy resources has led to a renewed interest in nuclear reactors including a new generation of molten salt reactors. One of the issues encountered in handling of molten chloride or fluoride salts is the inability of metals to form and retain a protective oxide surface layer, generally chromium oxide. The low chromium content, nickel-based alloy INOR-8, later marketed as Hastelloy N, was specifically developed to contain molten fluorides. This alloy had some deficiencies, but its composition resulted in it incurring far less chromium depletion by the molten fluoride salts than alloys like 316 stainless steel. For the next generation of molten salt reactors, an alloy with pressure vessel code approval and higher temperature capability than Hastelloy N is required. Consequently, several reactor designers have reportedly chosen to build the reactor containment vessel from 316H stainless steel. In order to minimize corrosion of the stainless steel by the molten fluoride salt (2LiF-BeF 2 ), it is proposed to add beryllium metal to the salt to react with impurities and provide a means to lower the oxidation potential thus making the salt less corrosive. Even so, there is a concern whether the beryllium would react with components of the stainless steel. To address this concern, static capsule tests were conducted in which selected amounts of beryllium were added to capsules containing 2LiF-BeF 2 (FLiBe) salt and 316H stainless steel and Hastelloy N samples. Following exposure, the samples were cleaned and examined using a variety of analysis techniques including, optical microscopy, SEM-EDS, XPS, LIBS, XRD and EPMA. Tensile samples were also exposed in capsules, and those were subjected to tensile testing. Notably, It was found that for the level of beryllium additions used in this study, intermetallic compounds were formed which could be detrimental to the long-term performance of the 316H stainless steel.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Characterization of anisotropic mechanical properties of polymer composites from a hybrid additive manufacturing-compression molding process using x-ray computer tomography

In this study, anisotropic stiffness tensors were reconstructed based on fiber orientation distributions obtained from X-ray computer tomography (xCT). A preform was manufactured via a big area additive manufacturing (BAAM) system with carbon fiber (CF) filled acrylonitrile butadiene styrene (ABS). The tailored preform from additive manufacturing (AM) was used in the compression molding (CM) process to produce a low-void high-performance thermoplastic composite panel. An xCT technique was employed to detect the fiber orientations in CF/ABS composites manufactured via three different methods: AM from BAAM, extrusion compression molding (ECM), and AM-CM. The anisotropic stiffness tensor was obtained from the composite panel manufactured via the three manufacturing methods (AM, ECM, and AMCM). A micromechanics theory was used to obtain the orthotropic stiffness tensors of the composite panels and compared with the experimental values. The predicted stiffness tensors of AM and AM-CM composite panels were used to study the deformation characteristics of a steering wheel during airbag deployment by performing finite element analysis (FEA). The approach developed in this study can be utilized for evaluating high-performance composites.

Pokkalla, Deepak↗

DOE OSTI2021

Testing and Modeling of Functionally Graded Aluminum-Doped Zinc Oxide Using Spark Plasma Sintering and Discrete Powder Layers of Varying Composition

Functionally graded material (FGM) ZnO is made via spark plasma sintering/field-assisted sintering technique (SPS/FAST) by varying the Al dopant content along the z-axis or pressing direction. A wide range of Al content (0–5 wt%) is used by adding Al powder to nanosized ZnO powder. Thermoelectric (TE) measurements are done on the FGM and individual layers made separately. X-ray diffraction (XRD) shows two phases, ZnO and spinel phase (ZnAl 2 O 4 ). High-resolution Raman spectroscopy reveals doped ZnO and spinel phase (ZnAl 2 O 4 ) spatially and shows segregation in the layer with highest Al content. Electron backscatter diffraction (EBSD) reveals noticeable grain growth with decreasing Al content, and there is a common, random preferred orientation in all layers. The tested properties are used to simulate efficiency curves for a discretely graded, five-layer FGM as well as a homogenous material, where both graded structures provide an opportunity to widen the current density ranges and therefore the temperature range of useful energy conversion.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Amphipathic Binder Integrating Ultrathin and Highly Ion-Conductive Sulfide Membrane for Cell-Level High-Energy-Density All-Solid-State Batteries

Current sulfide solid-state electrolyte (SE) membranes utilized in all-solid-state lithium batteries (ASLBs) have a high thickness (0.5–1.0 mm) and low ion conductance (<25 mS), which limit the cell-level energy and power densities. Therefore, based on ethyl cellulose's unique amphipathic molecular structure, superior thermal stability, and excellent binding capability, this work fabricates a freestanding SE membrane with an ultralow thickness of 47 µm. With ethyl cellulose as an effective disperser and a binder, the Li 6 PS 5 Cl is uniformly dispersed in toluene and possesses superior film formability. In addition, an ultralow areal resistance of 4.32 Ω cm -2 and a remarkable ion conductance of 291 mS (one order higher than the state-of-the-art sulfide SE membrane) are achieved. The ASLBs assembled with this SE membrane deliver cell-level high gravimetric and volumetric energy densities of 175 Wh kg -1 and 675 Wh L -1 , individually.

25 ENERGY STORAGE↗

DOE OSTI2021

Post weld heat treatment and operating temperature effect on tribological behavior of laser cladded stellite 21 coating

This study intends to investigate the feasibility of using laser cladding as a potential process to repair hot working tools by a hardfacing process. A Stellite 21 alloy coating was printed on a 350 maraging steel via laser cladding and the coating microstructure and tribological performance were characterized in as printed conditions and after heat treatment. Such a laser-processed coating showed a high integrity with little porosity and good bonding with the substrate. The Stellite coating produced substantially lower friction and a smoother contact area but had inferior wear resistance compared with the maraging steel substrate. Post process heat treatment at 650 °C for 20 h led to significant amount of strain-induced FCC to HCP phase transformation but had little improvement in wear resistance. Detailed materials characterization using X-ray diffraction and electron microscopy provided fundamental insights to the underlying mechanisms. This study opens the door for future R&D for tool surface repair by laser cladding.

36 MATERIALS SCIENCE↗