Caleb Robb | Search NASA

NASA NTRSDate not supplied

Design of a Propeller with Global Minimum Torque

Academia, industry, and Government are actively working towards a future where dozens of small to large Unmanned Aerial Systems (UAS) are present within urban environments. In this environment, high noise pollution and inefficiencies have the potential to render these new technologies impractical due to public annoyance and nonacceptance. This study aims to design and analyze a novel propeller design for minimum global torque using an optimization algorithm to find the full three dimensional solution of maximum efficiency. This resulted in a 𝐶 𝑙 distribution defining the global minimum torque solution for propeller design which corresponded with moving as much lift inboard as possible and reducing lift rapidly at the blade tip. The novel propeller (dubbed "Prandtl" propeller) was then compared with the current gold standard in propeller design, a minimum induced loss (MIL) propeller, which had all the same geometric properties except for blade twist and produced the same amount of thrust at the same advance ratio. The results of multiple iterations of Prandtl propellers showed an increase in efficiency of 2.0-3.3% for the Prandtl blade when compared to the equivalent MIL blade. A potential added benefit of this blade design is lower noise generation due to the lower lift loading at the tip reducing the large shear layer intensity which is the point source of noise in propellers. Two major breakthroughs for enabling widespread use of UAS in urban environments are noise reduction and vehicle efficiency, and this new propeller design has the potential to provide both.

Propeller↗

NASA NTRSDate not supplied

Design of a Propeller with Global Minimum Torque

Academia, industry, and Government are actively working towards a future where dozens of small to large Unmanned Aerial Systems (UAS) are present within urban environments. In this environment, high noise pollution and inefficiencies have the potential to render these new technologies impractical due to public annoyance and nonacceptance. This study aims to design and analyze a novel propeller design for minimum global torque using an optimization algorithm to find the full three dimensional solution of maximum efficiency. This resulted in a 𝐶 𝑙 distribution defining the global minimum torque solution for propeller design which corresponded with moving as much lift inboard as possible and reducing lift rapidly at the blade tip. The novel propeller (dubbed "Prandtl" propeller) was then compared with the current gold standard in propeller design, a minimum induced loss (MIL) propeller, which had all the same geometric properties except for blade twist and produced the same amount of thrust at the same advance ratio. The results of multiple iterations of Prandtl propellers showed an increase in efficiency of 2.0-3.3% for the Prandtl blade when compared to the equivalent MIL blade. A potential added benefit of this blade design is lower noise generation due to the lower lift loading at the tip reducing the large shear layer intensity which is the point source of noise in propellers. Two major breakthroughs for enabling widespread use of UAS in urban environments are noise reduction and vehicle efficiency, and this new propeller design has the potential to provide both.

Propeller↗

NASA NTRSDate not supplied

Assessing Huygens Probe Entry, Descent, and Landing at Titan Simulation using Dragonfly Atmosphere Model

Dragonfly is a New Frontiers Program mission that will deliver a rotorcraft to Saturn's moon, Titan. This mission follows Huygens as the previous mission that successfully landed a vehicle on Titan. A flight mechanics simulation of Dragonfly's Entry, Descent, and Landing sequence has been developed using the Program to Optimize Simulated Trajectories II. The simulation incorporates several subsystem models, including aerodynamics, gravity, and mass properties, to fully capture the multi-body six degree of freedom dynamics. Among all the subsystem models that inform the Entry, Descent, and Landing dynamics, the atmosphere model of Titan is a critical component. The atmosphere model characterizes the density, temperature, pressure, and winds that the entry vehicle experiences during the descent. This impacts several aspects of the descent such as the peak heating, aerodynamics, parachute release conditions, the dynamics of the vehicle and parachutes, and the landing ellipse. In the course of developing Dragonfly, an updated model of the Titan atmosphere has been created corresponding to Dragonfly's arrival in the mid-2030s, approximately one Titan year after the Huygens mission successfully landed a probe on Titan. This work leverages previous work done to investigate Huygens EDL sequence to assess the atmosphere model developed for Dragonfly. This is done by utilizing the updated Titan atmosphere model, the Dragonfly atmosphere model, within the Huygens POST2-based flight simulation with the goal of characterizing the differences between the atmospheric models and assessing how the Dragonfly atmosphere model impacts Huygens entry dynamics.

Huygens↗

NASA NTRSDate not supplied

Dragonfly Mission Entry and Descent Modeling and Simulation Overview

Dragonfly is a New Frontiers Program mission, led by The Johns Hopkins Applied Physics Laboratory, that will deliver a rotorcraft lander to Saturn’s moon, Titan. The focus of this work is to analyze the trajectory of the entry vehicle from cruise stage separation until lander separation. This analysis is done by the NASA Langley Research Center Entry, Descent, and Landing team using the Program to Optimize Trajectories II. This paper provides an overview of the current design and the robustness of the overall entry sequence using a Monte Carlo uncertainty analysis. The work presented in this study includes the updated design, models, and analysis completed since the Dragonfly Entry, Descent, and Landing Mission Preliminary Design Review.

Simulation↗

NASA NTRSDate not supplied

Assessing Huygens Probe Entry, Descent, and Landing at Titan Simulation using Dragonfly Atmosphere Model

Dragonfly is a New Frontiers Program mission that will deliver a rotorcraft to Saturn's moon, Titan. This mission follows Huygens as the previous mission that successfully landed a vehicle on Titan. A flight mechanics simulation of Dragonfly's Entry, Descent, and Landing sequence has been developed using the Program to Optimize Simulated Trajectories II. The simulation incorporates several subsystem models, including aerodynamics, gravity, and mass properties, to fully capture the multi-body six degree of freedom dynamics. Among all the subsystem models that inform the Entry, Descent, and Landing dynamics, the atmosphere model of Titan is a critical component. The atmosphere model characterizes the density, temperature, pressure, and winds that the entry vehicle experiences during the descent. This impacts several aspects of the descent such as the peak heating, aerodynamics, parachute release conditions, the dynamics of the vehicle and parachutes, and the landing ellipse. In the course of developing Dragonfly, an updated model of the Titan atmosphere has been created corresponding to Dragonfly's arrival in the mid-2030s, approximately one Titan year after the Huygens mission successfully landed a probe on Titan. This work leverages previous work done to investigate Huygens EDL sequence to assess the atmosphere model developed for Dragonfly. This is done by utilizing the updated Titan atmosphere model, the Dragonfly atmosphere model, within the Huygens POST2-based flight simulation with the goal of characterizing the differences between the atmospheric models and assessing how the Dragonfly atmosphere model impacts Huygens entry dynamics.

Entry Descent Landing↗

NASA NTRSDate not supplied

Dragonfly Mission Entry and Descent Modeling and Simulation Overview

Dragonfly is a New Frontiers Program mission, led by The Johns Hopkins Applied Physics Laboratory, that will deliver a rotorcraft lander to Saturn’s moon, Titan. The focus of this work is to analyze the trajectory of the entry vehicle from cruise stage separation until lander separation. This analysis is done by the NASA Langley Research Center Entry, Descent, and Landing team using the Program to Optimize Trajectories II. This paper provides an overview of the current design and the robustness of the overall entry sequence using a Monte Carlo uncertainty analysis. The work presented in this study includes the updated design, models, and analysis completed since the Dragonfly Entry, Descent, and Landing Mission Preliminary Design Review.

Simulation↗