Engineering topics

Camino, Fernando

Publications and source records attributed to Camino, Fernando.

11 records

DOE OSTI2026

Epitaxial registry and transport properties in V4O7 thin films

We report the growth of V4O7 thin films deposited simultaneously on amorphous SiO2 and crystalline c-cut Al2O3 substrates. x-ray diffraction shows that films grown on SiO2 are polycrystalline with no preferred orientation, while films grown on Al2O3 exhibit a well-defined out-of-plane orientation and an in-plane registry consistent with epitaxial growth. Transmission electron microscopy confirms the crystallographic relationship between the V4O7 film and the Al2O3 substrate. Atomic force microscopy indicates substantially lower surface roughness for films grown on Al2O3 (~6 nm) compared to those grown on SiO2 (~22 nm), and Raman spectroscopy confirms stabilization of the same V4O7 phase on both substrates. Electrical transport measurements reveal a metal–insulator transition near 244 K for both substrates, with thermal hysteresis not exceeding ~1 K. Although the transition temperature remains essentially unchanged, films grown on Al2O3 exhibit higher conductivity over the entire temperature range, exceeding that of films grown on SiO2 by approximately two orders of magnitude at 100 K and by a factor of five at 300 K. These results indicate that the conductivity differences are consistent with variations in microstructural connectivity associated with crystallographic order.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Crystallographic registry in epitaxial V3O5 thin films

Crystallographic orientation plays a central role in determining transport properties in correlated oxides with low-hysteresis metal–insulator transitions. Here, V3O5 thin films were grown on Al2O3 (0001) and their crystallographic registry was evaluated using x-ray diffraction and cross-sectional transmission electron microscopy. θ–2θ measurements show a single out-of-plane orientation defined by the (202) reflection. Azimuthal φ-scans of the V3O5 (310) reflection exhibit twelve discrete maxima over 360°, indicating a finite set of in-plane orientations imposed by the substrate symmetry. High-resolution TEM and fast Fourier transform analysis confirm crystallographic coherence at the film–substrate interface. The electrical conductivity exhibits a metal–insulator transition at TMIT ≈ 423 K with no measurable thermal hysteresis and a total change of ~1.6 orders of magnitude between 300 and 480 K. These results establish crystallographic registry in epitaxial V3O5 thin films and provide a structurally well-defined system for future studies of orientation-dependent transport.\r\nT

36 MATERIALS SCIENCE↗

DOE OSTI2024

Low cost switching circuit for van der Pauw resistivity and Hall measurements at various temperatures

The electrical characterization of materials, particularly superconductors, semiconductors, and those undergoing metal-insulator transitions (MITs), relies significantly on resistivity and Hall measurements as a function of temperature. The van der Pauw four-point probe method is commonly used for such measurements, which involves resistance measurements for different circuit configurations connected to sample contacts. However, repeating these measurements at different temperatures is challenging and time consuming. Here, this study introduces a novel approach utilizing a switching circuit controlled by an Arduino device and a LabVIEW program to automate resistance measurements for different electrical configurations. The effectiveness of this setup was demonstrated by testing V 2 O 3 thin film samples deposited on Al 2 O 3 (001) substrates using DC magnetron sputtering. The MIT temperature of the sample was 115 K during heating and 100 K during cooling. The sample exhibited p-type charge carriers with a Hall coefficient of 1.3 ± 0.1 x 10 -4 cm 3 /C and Hall mobility of 1.7 x 10 -1 cm 2 /V∙s, which is consistent with findings from other studies employing commercial equipment.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Signature of Correlated Insulator in Electric Field Controlled Superlattice

On a two-dimensional crystal, a “superlattice” with nanometer-scale periodicity can be imposed to tune the Bloch electron spectrum, enabling novel physical properties inaccessible in the original crystal. While creating 2D superlattices by means of nanopatterned electric gates has been studied for band structure engineering in recent years, evidence of electron correlations-which drive many problems at the forefront of physics research-remains to be uncovered. Here, in this work, we demonstrate signatures of a correlated insulator phase in Bernal-stacked bilayer graphene modulated by a gate-defined superlattice potential, manifested as resistance peaks centered at integer multiples of single electron per superlattice unit cell carrier densities. The observation is consistent with the formation of a stack of flat low-energy bands due to the superlattice potential combined with inversion symmetry breaking. Our work paves the way to custom-designed superlattices for studying band structure engineering and strongly correlated electrons in 2D materials.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Single Crystalline GeSe Van Der Waals Ribbons With Uniform Layer Stacking, High Carrier Mobility, and Adjustable Edge Morphology

Abstract Performance of the group IV monochalcogenide GeSe in solar cells, electronic, and optoelectronic devices is expected to improve when high‐quality single crystalline material is used rather than polycrystalline films. Crystalline flakes represent an attractive alternative to bulk single crystals as their synthesis may be developed to be scalable, faster, and with higher overall yield. However, large – and especially large and thin – single crystal flakes are notoriously hard to synthesize. Here it is demonstrated that vapor‐liquid‐solid growth combined with direct lateral vapor‐solid incorporation produces high‐quality single crystalline GeSe ribbons with tens of micrometers size and controllable thickness. Electron microscopy shows that the ribbons exhibit perfect equilibrium (AB) van der Waals stacking order without extended defects across the entire thickness, in contrast to the conventional case of substrate‐supported flakes where material is added via layer‐by‐layer nucleation and growth on the basal plane. Electrical measurements show anisotropic transport and a high Hall mobility of 85 cm 2 V −1 s −1 , on par with the best single crystals to date. Growth from mixed GeSe and SnSe vapors, finally, yields ribbons with unchanged structure and composition but with jagged edges, promising for applications that rely on ample chemically active edge sites, such as catalysis or photocatalysis.

99 GENERAL AND MISCELLANEOUS↗

DOE OSTI2023

Oxidation Driven Thin‐Film Solid‐State Metal Dealloying Forming Bicontinuous Nanostructures

Abstract Solid‐state metal dealloying (SSMD) is a promising method for fabricating nanoscale metallic composites and nanoporous metals across a range of materials. Thin‐film SSMD is particularly attractive due to its ability to create fine features via solid‐state interfacial reactions within a thin‐film geometry, which can be integrated into devices for various applications. This work examines a new dealloying couple, namely the Nb–Al alloy with the dealloying agent Sc, as previously predicted in the machine‐learning (ML) models. Prior ML predictions aimed to guide the design of nanoarchitectured materials through dealloying, relying on intuition‐driven discovery within a large parameter space. However, this work reveals that at the nanoscale, the involvement of oxygen in thin film processing may instead drive the dealloying process, resulting in the formation of bicontinuous nanostructures similar to those formed by metal‐agent dealloying. The phase evolution, as well as chemical and morphological changes, are closely analyzed using a combination of X‐ray absorption spectroscopy, diffraction, and scanning transmission electron microscopy to understand the mechanisms behind nanostructure formation. The findings suggest a potential pathway for utilizing oxygen to drive the formation of bicontinuous metal–metal oxide nanocomposites, paving the way for further development of functional nanoporous materials in diverse fields.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Hysteretic Responses of Skyrmion Lattices to Electric Fields in Magnetoelectric Cu 2 OSeO 3

Electric field control of topologically nontrivial magnetic textures, such as skyrmions, provides a paradigm shift for future spintronics beyond current silicon-based technology. While significant progress has been made by X-ray and neutron scattering studies, direct observation of such nanoscale spin structures and their dynamics driven by external electric fields remains a challenge to understand underlying mechanisms and harness functionalities. Here, using Lorentz transmission electron microscopy combined with in situ electric and magnetic fields at liquid helium temperatures, we report the crystallographic-orientation dependent skyrmion responses to electric fields in thin slabs of magnetoelectric Cu 2 OSeO 3 . We show electric fields not only stabilize the hexagonally packed skyrmion lattices in the entire sample in a hysteretic manner but also induce the rotation of their reciprocal vector discretely by 30°. Furthermore, the nonvolatile and energy-efficient skyrmion-lattice control by electric fields demonstrated in this work provides an important foundation for designing skyrmion-based qubits and memory devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2023

Effects of Focused Ion Beam Lithography on La 2– x Sr x CuO 4 Single Crystals

Focused ion beam (FIB) milling is a mask-free lithography technique that allows the precise shaping of 3D materials on the micron and sub-micron scale. The recent discovery of electronic nematicity in La 2–x Sr x CuO 4 (LSCO) thin films triggered the search for the same phenomenon in bulk LSCO crystals. With this motivation, we have systematically explored FIB patterning of bulk LSCO crystals into micro-devices suitable for longitudinal and transverse resistivity measurements. We found that several detrimental factors can affect the result, ultimately compromising the possibility of effectively using FIB milling to fabricate sub-micrometer LSCO devices, especially in the underdoped regime.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Evolution of micro-pores in Ni–Cr alloys via molten salt dealloying

Porous materials with high specific surface area, high porosity, and high electrical conductivity are promising materials for functional applications, including catalysis, sensing, and energy storage. Molten salt dealloying was recently demonstrated in microwires as an alternative method to fabricate porous structures. The method takes advantage of the selective dissolution process introduced by impurities often observed in molten salt corrosion. This work further investigates molten salt dealloying in bulk Ni–20Cr alloy in both KCl–MgCl 2 and KCl–NaCl salts at 700 °C, using scanning electron microscopy, energy dispersive spectroscopy, and X-ray diffraction (XRD), as well as synchrotron X-ray nano-tomography. Micro-sized pores with irregular shapes and sizes ranging from sub-micron to several microns and ligaments formed during the process, while the molten salt dealloying was found to progress several microns into the bulk materials within 1–16 h, a relatively short reaction time, enhancing the practicality of using the method for synthesis. The ligament size increased from ~ 0.7 μm to ~ 1.3 μm in KCl–MgCl 2 from 1 to 16 h due to coarsening, while remaining ~ 0.4 μm in KCl–NaCl during 16 h of exposure. The XRD analysis shows that the corrosion occurred primarily near the surface of the bulk sample, and Cr 2 O 3 was identified as a corrosion product when the reaction was conducted in an air environment (controlled amount sealed in capillaries); thus surface oxides are likely to slow the morphological coarsening rate by hindering the surface diffusion in the dealloyed structure. 3D-connected pores and grain boundary corrosion were visualized by synchrotron X-ray nano-tomography. This study provides insights into the morphological and chemical evolution of molten salt dealloying in bulk materials, with a connection to molten salt corrosion concerns in the design of next-generation nuclear and solar energy power plants.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Topological Hall Effect Anisotropy in Kagome Bilayer Metal Fe 3 Sn 2

Kagome lattice materials attract growing interest for their topological properties and flat-bands in electronic structure. We present comprehensive study on the anisotropy and out-of-plane electric transport in Fe 3 Sn 2 , a metal with bilayer of Fe kagome planes and with massive Dirac fermions that features high-temperature non-collinear magnetic structure and magnetic skyrmions. For the electrical current path along the c-axis, in micron-size crystals, we found a large topological Hall effect (THE) over a wide temperature range down to spin-glass state. Twofold and fourfold angular magnetoresistance are observed for different magnetic phases, reflecting the competition of magnetic interactions and magnetic anisotropy in kagome lattice that preserve robust topological Hall effect for inter kagomebilayer currents. This information provides new insight into the anisotropy in Fe 3 Sn 2 , of interest in skyrmionicbubble application-related micron-size devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2022

Smart material based multilayered microbeam structures for spatial self-deployment and reconfiguration: A residual stress approach

Alleviation of the potentially damaging effects induced by residual stresses was comprehensively investigated in previous research. Here, this paper, however, presents a spatially self-deployable and reconfigurable multilayered microbeam which takes advantage of residual stresses and shape memory effects. Reconfigurable mechanism of a typical four-layered microbeam composed of Pt\Ni 50 Ti 50 \Ni 50 Ti 50 \Pt is introduced, followed by analytical modeling of the maximum distance of the self-deployed gap as functions of variable structural and material parameters, including compressive residual stress in Pt layers and tensile residual stress in Ni 50 Ti 50 layers. Analytical solutions given by the static model agree well with the results obtained via finite element models (FEMs). Fabrication, characterization, and in-situ experiments were carried out to validate the feasibility of deployment of the as-released four-layered microbeam. The maximum distance of the gap was measured to be 41.39 μm at 20 °C, which could be increased to 51.73 μm thanks to controllable reconfiguration driven by shape memory effects. Theoretical analysis of such self-deployment and reconfiguration suggested a tensile residual stress increase by 52 MPa in Ni 50 Ti 50 layers. The multilayered microbeam structure with capabilities of self-deployment and reconfiguration offers great potential for various emerging applications, such as micro robotics, medical drug delivery devices, and intelligent chip scale spacecraft.

36 MATERIALS SCIENCE↗