Search NASA⌕ Search

Engineering topics

Canlas, Christian P.

Publications and source records attributed to Canlas, Christian P..

Artificial zeolites

Zeolites are industrially important materials possessing high Bronsted acidity and shape-selectivity. However, their inherently small pores restrict application for catalytic conversion of bulky molecules. A method of synthesis of ‘artificial’ zeolites. The artificial zeolites have well-tailored Bronsted and Lewis acid sites prepared on mesostructured silica to circumvent this limitation. This novel approach utilizes atomic layer deposition to tailor both porosity and acid speciation, providing exquisite control over catalytic behavior and enabling systematic studies.

Elam, Jeffrey W.↗

Tunable Solid Acid Catalyst Thin Films Prepared by Atomic Layer Deposition

Solid acid catalysts, including zeolites and amorphous silica-aluminas (ASAs), are industrially important materials widely used in the fuel and petrochemical industries. The versatility of zeolites is due to the Brønsted acidity of the bridging hydroxyl and shape selectivity that can be tailored during and after synthesis. This is in contrast to amorphous silica-alumina, where tailoring acidity is a major challenge as the Brønsted acid structure in ASA is still debated. In both cases, however, the pore size and acidity cannot be tuned independently, and this is particularly limiting in the application of biomass conversion, where zeolite pores are too small for the molecules of interest. Herein, we present a method using atomic layer deposition (ALD) to prepare thin films of solid acid materials where the ratio of Brønsted to Lewis acid sites can be tuned precisely. This capability, combined with the sub-nm pore size control afforded by ALD yields a powerful and flexible method for synthesizing solid acid catalysts inside virtually any mesoporous host. We demonstrate the utility of these materials in two acid-catalyzed reactions relevant to biomass conversion: (1) Meerwein–Ponndorf–Verley–Oppenauer (MPVO) reaction and dehydration of fructose and (2) cascade reaction of glucose to 5-hydroxymethylfurfural. Finally, we propose a plausible structure for the Brønsted acid sites in our materials based on infrared spectroscopy and solid-state nuclear magnetic resonance measurements and density functional theory calculations and argue that this same structure might apply to conventional ASAs as well.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Synthesis and stabilization of small Pt nanoparticles on TiO 2 partially masked by SiO 2

Controlling metal nanoparticle size and preserving metal dispersion at elevated temperature remain key challenges in designing new supported metal catalysts. Many methods have been proposed to stabilize metal nanoparticles for catalysis, but the use of specialized equipment or metal precursors can limit the application of these methods for scalable production. Here, we demonstrate a synthesis strategy to improve the dispersion and thermal stability of Pt nanoparticles on an oxide support. A thin SiO 2 coat (<2 nm) was deposited on TiO2 through repeated condensation cycles of tetraethyl orthosilicate (TEOS) with or without an organic template on the surface. H 2 PtCl 6 was deposited using wetness impregnation, and the samples were dried, calcined, and reduced. The as-synthesized Pt nanoparticles are 1–2 nm by TEM and maintain dispersion >45% by CO chemisorption even after prolonged heating at 500 °C, whereas Pt nanoparticles on unmodified TiO 2 are less dispersed (~33%) and their dispersion falls further upon prolonged heating. Ethylene hydrogenation demonstrates that the Pt nanoparticles on modified TiO 2 preserve the catalytic activities of Pt on unmodified TiO 2 . The use of wet chemistry-based oxide modification and wetness impregnation makes this strategy a scalable and generalizable synthesis method to prepare other supported metal nanoparticles for catalysis applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Tailoring nanopore formation in atomic layer deposited ultrathin films [Nanopore formation in atomic layer deposited ultrathin films]

Selectivity is a critical attribute of catalysts used in manufacturing of essential and fine chemicals. An excellent way to induce selectivity in catalysts is by using ultrathin films with tailored nanoporosity. For instance, nanopores can be created in atomic layer deposition (ALD) ultrathin over-coatings on supported metal nanoparticles by subjecting the coatings to high temperature annealing. These nanopores expose the active surface of the underlying metal nanoparticles. The dimensions of these nanopores can be tuned to impart shape selectivity: only reactants or products with a specific size or shape can fit inside the pore. In this work, the authors explore the underlying mechanism driving nanopore formation in ALD films. Ultrathin films of ALD TiO 2 (similar to 2.5 nm thick) and ALD Al 2 O 3 (similar to 4.9 nm thick) were deposited on nonporous gamma-Al 2 O 3 nanoparticles. The pore formation and evolution were monitored in situ during thermal annealing using small-angle x-ray scattering (SAXS), and the crystallinity was monitored by in situ x-ray diffraction. A correlation between the nanopore formation and amorphous to crystalline phase transitions in the ALD layers was observed. The authors hypothesize that the pores form through the relaxation of stress induced by densification of the ALD films during the phase transitions. In conclusion, the authors developed a mathematical model to evaluate this hypothesis and found remarkable agreement between the model and the SAXS measurements.

36 MATERIALS SCIENCE↗

Exploring Pore Formation of Atomic Layer-Deposited Overlayers by in Situ Small- and Wide-Angle X-ray Scattering

In this work, we explore the pore structure of overcoated materials by in situ synchrotron small- and wide-angle X-ray scattering (SAXS)/(WAXS). Thin films of aluminum oxide (Al2O3) and titanium dioxide (TiO2) with thicknesses of 4.9 and 2.5 nm, respectively, are prepared by atomic layer deposition (ALD) on non-porous nanoparticles. In situ X-ray measurements reveal that porosity is induced in the ALD films by annealing the samples at high temperature. Moreover, this pore formation can be attributed to densification resulting from an amorphous to crystalline phase transition of the ALD films as confirmed by high resolution X-ray diffraction (XRD) and pair distribution function (PDF). Simultaneous SAXS/WAXS results not only show that the porosity is formed by this phase transition but also that the pore size increases with temperature.

Li, Tao↗

High thermal stability of La 2 O 3 and CeO 2 -stabilized tetragonal ZrO 2

Catalyst support materials of tetragonal ZrO 2 , stabilized by either La 2 O 3 (La 2 O 3 -ZrO 2 ) or CeO 2 (CeO 2 -ZrO 2 ), were synthesized under hydrothermal conditions at 200 °C with NH 4 OH or tetramethylammonium hydroxide as the mineralizer. From In Situ synchrotron powder X-ray diffraction and small-angle X-ray scattering measurements, the calcined La 2 O 3 -ZrO 2 and CeO 2 -ZrO 2 supports were nonporous nanocrystallites that exhibited rectangular shapes with thermal stability up to 1000 °C in air. These supports had an average size of ~10 nm and a surface area of 59-97 m 2 /g. The catalysts Pt/La 2 O 3 -ZrO 2 and Pt/CeO 2 -ZrO 2 were prepared by using atomic layer deposition with varying Pt loadings from 6.3-12.4 wt %. Mono-dispersed Pt nanoparticles of ~3 nm were obtained for these catalysts. As a result, the incorporation of La 2 O 3 and CeO 2 into the t-ZrO 2 structure did not affect the nature of the active sites for the Pt/ZrO 2 catalysts for the water-gas-shift (WGS) reaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Increasing the Aromatic Selectivity of Quinoline Hydrogenolysis Using Pd/MOx–Al2O3

Catalysts consisting of Pd nanoparticles supported on highly dispersed TiOx–Al2O3, TaOx–Al2O3, and MoOx–Al2O3 are studied for catalytic quinoline hydrogenation and selective C–N bond cleavage at 275 °C and 20 bar H2. The Pd/MOx–Al2O3 materials exhibit significantly greater aromatic product selectivity and thus 10–15 % less required H2 for a given level of denitrogenation relative to an unmodified Pd/Al2O3 catalyst.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗