Search NASA⌕ Search

Engineering topics

Cao, D.

Publications and source records attributed to Cao, D..

At least 37 records · Page 2

Enhanced laser-energy coupling with small-spot distributed phase plates (SG5-650) in OMEGA DT cryogenic target implosions

Cryogenic deuterium–tritium ice target implosions on OMEGA with new small-spot (SG5-650) distributed phase plates (DPPs) achieved an (11 ± 4)% increase in energy coupling compared to implosions with larger-spot SG5-850 DPPs by decreasing the ratio of the laser spot diameter to the target diameter from 0.93 to 0.75. The SG5-650 DPPs provide a focus spot size of 674 μm, which is defined as the diameter that encircles 95% of the measured beam energy compared to 834 μm for the SG5-850, which are the standard DPPs in cryogenic target implosions on OMEGA. The hydrodynamic efficiency, defined as the ratio of the kinetic energy in the imploding shell to the laser energy, increased from 4.5% to 5.0% based on radiation-hydrodynamic calculations benchmarked to shell trajectory and bang-time measurements. Furthermore, the higher coupling came with a trade-off of an increased hot-electron production as well as increased hydrodynamic instabilities seeded by a larger mode-10 amplitude from the beam port geometry, both of which may have reduced the fusion neutron production and areal density.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Using statistical modeling to predict and understand fusion experiments

Over 300 cryogenic layered direct-drive inertial confinement fusion implosions have been successfully executed on the OMEGA Laser System in the last decade. However, extracting sufficient understanding from these experiments to develop new designs or to identify or mitigate degradation sources remains challenging. Recently, a statistical modeling approach was developed to successfully design and predict improved implosion experiments on OMEGA. Here, we show that one-dimensional simulations can be used to predict the outcomes of systematically perturbed three-dimensional simulations and that this statistical modeling approach can be used to identify or rule out physical mechanisms for some of the degradation sources observed on the OMEGA Laser System for direct-drive cryogenic inertial confinement fusion. In this instance, we investigate the fusion yield dependencies on the ion temperature asymmetries and laser beam size observed in experiments by comparing with trends in three-dimensional synthetic simulation databases. Using the statistical model on these systematically perturbed simulations, we find that the statistically inferred dependency on the measured ion temperature asymmetries is well explained by imposed ℓ =1 modes. However, we find that the dependency on the laser beam size is only dominated by the illumination non-uniformity for some extreme cases.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Density evolution after shock release from laser-driven polystyrene (CH) targets in inertial confinement fusion

The evolution of the plasma density in the rarefaction wave formed after a laser-driven shock is released from a CH foil was measured using optical interferometry. Here, it was found that the plasma density profile is very sensitive to the conditions at the back surface of the foil before the shock release. Dedicated experiments demonstrated that radiation preheat by coronal x-rays caused early expansion of the back surface and faster expansion of the rarefaction wave. Radiation-hydrodynamics simulations with accurate modeling of radiation preheat from the plasma corona are in good agreement with the experimental results. The early expansion of material interfaces due to coronal x-ray preheat must be evaluated in designing and interpreting laser-driven inertial confinement fusion experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Experimentally Inferred Fusion Yield Dependencies of OMEGA Inertial Confinement Fusion Implosions

Statistical modeling of experimental and simulation databases has enabled the development of an accurate predictive capability for deuterium-tritium layered cryogenic implosions at the OMEGA laser. Here, a physics-based statistical mapping framework is described and used to uncover the dependencies of the fusion yield. This model is used to identify and quantify the degradation mechanisms of the fusion yield in direct-drive implosions on OMEGA. The yield is found to be reduced by the ratio of laser beam to target radius, the asymmetry in inferred ion temperatures from the $l$ = 1 mode, the time span over which tritium fuel has decayed, and parameters related to the implosion hydrodynamic stability. When adjusted for tritium decay and $l$ = 1 mode, the highest yield in OMEGA cryogenic implosions is predicted to exceed 2 × 10 14 fusion reactions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Direct Measurements of DT Fuel Preheat from Hot Electrons in Direct-Drive Inertial Confinement Fusion

Hot electrons generated by laser-plasma instabilities degrade the performance of laser-fusion implosions by preheating the DT fuel and reducing core compression. The hot-electron energy deposition in the DT fuel has been directly measured for the first time by comparing the hard x-ray signals between DT-layered and mass-equivalent ablator-only implosions. The electron energy deposition profile in the fuel is inferred through dedicated experiments using Cu-doped payloads of varying thickness. The measured preheat energy accurately explains the areal-density degradation observed in many OMEGA implosions. Furthermore, this technique can be used to assess the viability of the direct-drive approach to laser fusion with respect to the scaling of hot-electron preheat with laser energy.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Mitigation of mode-one asymmetry in laser-direct-drive inertial confinement fusion implosions

Nonuniformities present in the laser illumination and target in laser-driven inertial confinement fusion experiments lead to an asymmetric compression of the target, resulting in an inefficient conversion of shell kinetic energy to thermal energy of the hot-spot plasma. In this paper, the effects of asymmetric compression of cryogenic deuterium tritium laser-direct-drive implosions are examined using a suite of nuclear and x-ray diagnostics on the OMEGA laser. The neutron-averaged hot-spot velocity (~uhs) and apparent ion temperature (Ti) asymmetry are determined from neutron time-of-flight measurements of the primary deuterium tritium fusion neutron energy spectrum, while the areal density (rhoR) of the compressed fuel surrounding the hot spot is inferred from measurements of the scattered neutron energy spectrum. The low-mode perturbations of the hot-spot shape are characterized from x-ray self-emission images recorded along three quasi-orthogonal lines of sight. Implosions with significant mode-1 laser drive asymmetries show large hot-spot velocities (>100 km/s) in a direction consistent with the hot-spot elongation observed in x-ray images, measured Ti asymmetry, and rhoR asymmetry. Laser drive corrections have been applied through shifting the initial target location in order to mitigate the observed asymmetry. With the asymmetry corrected, a more-symmetric hot spot is observed with reduced ~uhs, Ti asymmetry, rhoR asymmetry, and a 30% increase in the fusion yield.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Mitigation of mode-one asymmetry in laser-direct-drive inertial confinement fusion implosions

Nonuniformities present in the laser illumination and target in laser-driven inertial confinement fusion experiments lead to an asymmetric compression of the target, resulting in an inefficient conversion of shell kinetic energy to thermal energy of the hot-spot plasma. In this paper, the effects of asymmetric compression of cryogenic deuterium tritium laser-direct-drive implosions are examined using a suite of nuclear and x-ray diagnostics on the OMEGA laser. The neutron-averaged hot-spot velocity (u → hs ) and apparent ion temperature (T i ) asymmetry are determined from neutron time-of-flight measurements of the primary deuterium tritium fusion neutron energy spectrum, while the areal density (ρR) of the compressed fuel surrounding the hot spot is inferred from measurements of the scattered neutron energy spectrum. Here, the low-mode perturbations of the hot-spot shape are characterized from x-ray self-emission images recorded along three quasi-orthogonal lines of sight. Implosions with significant mode-1 laser drive asymmetries show large hot-spot velocities (>100 km/s) in a direction consistent with the hot-spot elongation observed in x-ray images, measured T i asymmetry, and ρR asymmetry. Laser drive corrections have been applied through shifting the initial target location in order to mitigate the observed asymmetry. With the asymmetry corrected, a more-symmetric hot spot is observed with reduced u → hs , T i asymmetry, ρR asymmetry, and a 30% increase in the fusion yield.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A multi-channel x-ray temporal diagnostic for measurement of time-resolved electron temperature in cryogenic deuterium–tritium implosions at OMEGA

Electron-temperature (T e ) measurements in implosions provide valuable diagnostic information, as Te is unaffected by residual flows and other non-thermal effects unlike ion temperature inferred from a fusion product spectrum. In OMEGA cryogenic implosions, measurement of T e (t) can be used to investigate effects related to time-resolved hot-spot energy balance. The proposed diagnostic utilizes five fast-rise (~15 ps) scintillator channels with distinct x-ray filtering. Furthermore, titanium and stepped aluminum filtering were chosen to maximize detector sensitivity in the 10 keV–20 keV range, as it has been shown that these x rays have similar density and temperature weighting to the emitted deuterium–tritium fusion neutrons. Initial data collected using a prototype nosecone on the existing neutron temporal diagnostic demonstrate the validity of this diagnostic technique. The proposed system will be capable of measuring spatially integrated T e (t) with 20 ps time resolution and <10% uncertainty at peak emission in cryogenic DT implosions.

47 OTHER INSTRUMENTATION↗

Observations of anomalous x-ray emission at early stages of hot-spot formation in deuterium-tritium cryogenic implosions

In DT cryogenic implosions, hot-spot x-ray self-emission is observed to begin at a larger shell radius than is predicted by a 1-D radiation-hydrodynamic implosion model. Laser-imprint is shown to explain the observation for a low-adiabat implosion. Furthermore, for more-stable implosions the data are not described by the imprint model and suggest there are additional sources of decompression of the dense fuel.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Direct-drive laser fusion: status, plans and future

Laser-direct drive (LDD), along with laser indirect (X-ray) drive (LID) and magnetic drive with pulsed power, is one of the three viable inertial confinement fusion approaches to achieving fusion ignition and gain in the laboratory. The LDD programme is primarily being executed at both the Omega Laser Facility at the Laboratory for Laser Energetics and at the National Ignition Facility (NIF) at Lawrence Livermore National Laboratory. LDD research at Omega includes cryogenic implosions, fundamental physics including material properties, hydrodynamics and laser–plasma interaction physics. LDD research on the NIF is focused on energy coupling and laser–plasma interactions physics at ignition-scale plasmas. Limited implosions on the NIF in the ‘polar-drive’ configuration, where the irradiation geometry is configured for LID, are also a feature of LDD research. The ability to conduct research over a large range of energy, power and scale size using both Omega and the NIF is a major positive aspect of LDD research that reduces the risk in scaling from OMEGA to megajoule-class lasers. Furthermore, the paper will summarize the present status of LDD research and plans for the future with the goal of ultimately achieving a burning plasma in the laboratory.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Impact of spatiotemporal smoothing on the two-plasmon–decay instability

Higher levels of hot electrons from the two-plasmon–decay instability are observed when smoothing by spectral dispersion (SSD) is turned off in directly driven inertial confinement fusion experiments at the Omega Laser Facility. This finding is explained using a hot-spot model based on speckle statistics and simulation results from the laser–plasma simulation environment. The model accurately reproduces the relative increase in hot-electron activity at two different drive intensities, although it slightly overestimates the absolute number of hot electrons in all cases. Extrapolating from the current ≈ 360-GHz system while adhering to the logic of the hot-spot model suggests that larger SSD bandwidth should significantly mitigate hot-electron generation, and legacy 1-THz OMEGA experiments appear to support this conclusion. These results demonstrate that it is essential to account for laser speckles and spatiotemporal smoothing to obtain quantitative agreement with experiments. A compilation of hot-electron data from the past two decades reveals several other important points: (1) many prior experiments are more easily understood using recent results from multibeam absolute instability theory; and (2) experiments with ignition-scale conditions produce less hot electrons compared to OMEGA spherical experiments for a given vacuum overlapped intensity, which is a promising result for validating performance predictions based on hydrodynamic scaling relations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Theory of ignition and burn propagation in inertial fusion implosions

A detailed analytic model is presented here to investigate the physics of burn propagation in inertially confined plasmas. The onset of ignition and burn propagation occurs when alpha heating of the hot spot causes rapid ablation of shell mass into the hot spot. This allows large energy gains to be achieved since most of the fuel mass is located in the shell. Here, we first present a comprehensive review of previous analytic models that have been used to describe the physics of hot-spot evolution and ignition; we then show that a proper description of a propagating burn wave requires a comprehensive model of hot spot and shell evolution that includes proper mass conservation in the shell, fusion reactivity, and fuel depletion. The analytic theory is in good agreement with detailed radiation-hydrodynamic simulations that predict the onset of burn propagation as occurring when the yield enhancement caused by alpha heating is between 15- and 25-fold, $f_α$ ~ 1.4, where $f_α$ = alpha energy deposited/hot-spot energy at bang time, and the hot-spot burnup fraction is approximately 2%. We show that the definition of ignition is not sensitive to the alpha-particle stopping power nor asymmetries provided that the absorbed fraction of alpha particles $θ_α$ is correctly accounted for. Finally, we use the results of 2-D simulations to show that even when $θ_α$ is small and unknown (as is true in hot spots with mid modes that have significant leakage of alpha particles into the surrounding cold bubbles), one can still relate the experimentally measureable parameter $\chi^{53}_α$ to the yield amplification and the burning-plasma parameter $Q^{\text{hs}}_α$ = alpha energy deposited/total input work delivered to the hot spot

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Anomalous Absorption by the Two-Plasmon Decay Instability

Radiation-hydrodynamic simulations of directly driven fusion experiments at the Omega Laser Facility predict absorption accurately when targets are driven at low overlapped laser intensity. Discrepancies appear at increased intensity, however, with higher-than-expected laser absorption on target. Strong correlations with signatures of the two-plasmon decay (TPD) instability—including half-harmonic and hard-x-ray emission—indicate that TPD is responsible for this anomalous absorption. Scattered light data suggest that up to ≈ 30 % of the laser power reaching quarter-critical density can be absorbed locally when the TPD threshold is exceeded. A scaling of absorption versus TPD threshold parameter was empirically determined and validated using the laser–plasma simulation environment code.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Interpreting the electron temperature inferred from x-ray continuum emission for direct-drive inertial confinement fusion implosions on OMEGA

In this paper, we present a theoretical framework for interpreting the hot-spot electron temperature ($T_e$) inferred from hard (10- to 20-keV) x-ray continuum emission for inertial confinement fusion implosions on OMEGA. We first show that the inferred $T_e$ represents the emission-weighted, harmonic mean of the hot-spot $T_e$ distribution, both spatially and temporally. A scheme is then provided for selecting a photon energy of which the emission weighting approximates neutron weighting. Simulations are then used to quantify the predicted relationship between the inferred T e , neutron-weighted T i , and implosion performance on OMEGA. In an ensemble of 1-D simulations, it was observed that hot-spot thermal nonequilibrium precluded a sufficiently unique mapping between the inferred $T_e$ and neutron-weighted T i . In 3-D simulations with low-harmonic-mode perturbations (i.e., laser beam power imbalance, target offset, and beam port geometry departures from spherical symmetry) and laser imprint (1 max = 200).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Development of a Squeeze Semisolid High-Pressure Die Casting Process for Magnesium Structural Parts

High-pressure die casting is the most common method used to produce magnesium castings, due to the excellent balance of cost and properties for high production volumes with limitations in terms of final mechanical properties. A newly developed process based on employing low injection speeds, in a range slightly over the standard semisolid speeds with a modified die, with thick gates and high die temperatures has been developed. Despite working with speeds that are not in the lamellar flow, the obtained parts present very low porosity, allowing the use thermal treatments to increase the ductility without producing blisters. The demonstration has been performed in a AM60B magnesium body joint produced by the squeeze casting process. Finally, the microstructure and the mechanical properties of as-cast and T4 heat-treated samples were studied. The results indicate the improvement of the mechanical properties in T4 heat-treated parts; specifically, a 40% improved deformation-to-failure, 40-60% improved penetration force and 90% of energy absorption were possible to obtain employing the newly developed SC + T4 process.

36 MATERIALS SCIENCE↗

A high precision calibration of the nonlinear energy response at Daya Bay

A high precision calibration of the nonlinearity in the energy response of the Daya Bay Reactor Neutrino Experiment’s antineutrino detectors is observed. The energy nonlinearity originates from the particle-dependent light yield of the scintillator and charge-dependent electronics response. The nonlinearity model is constrained by γ calibration points from deployed and naturally occurring radioactive sources, the β spectrum from 12 B decays, and a direct measurement of the electronics nonlinearity with a new flash analog-to-digital converter readout system. With this beind said, less than 0.5% uncertainty in the energy nonlinearity calibration is achieved for positrons of kinetic energies greater than 1 MeV.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗