Search NASA⌕ Search

Engineering topics

Capone, F. J.

Publications and source records attributed to Capone, F. J..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2003

Recommended Experimental Procedures for Evaluation of Abrupt Wing Stall Characteristics

This paper presents a review of the experimental program under the Abrupt Wing Stall (AWS) Program. Candidate figures of merit from conventional static tunnel tests are summarized and correlated with data obtained in unique free-to-roll tests. Where possible, free-to-roll results are also correlated with flight data. Based on extensive studies of static experimental figures of merit in the Abrupt Wing Stall Program for four different aircraft configurations, no one specific figure of merit consistently flagged a warning of potential lateral activity when actual activity was seen to occur in the free-to-roll experiments. However, these studies pointed out the importance of measuring and recording the root mean square signals of the force balance.

Capone, F. J.↗
NASA NTRS2003

Development of a Free-to-Roll Transonic Test Capability (Invited)

As part of the NASA/Navy Abrupt Wing Stall Program, a relatively low-cost, rapid-access wind-tunnel free-to-roll rig was developed. This rig combines the use of conventional models and test apparatuses to evaluate both transonic performance and wing-drop/rock tendencies in a single tunnel entry. A description of the test hardware as well as a description of the experimental procedures is given. The free-to-roll test rig has been used successfully to assess the static and dynamic characteristics of three different configurations--two configurations that exhibit uncommanded lateral motions, (pre-production F/A-18E and AV-8B), and one that did not (F/A-18C).

Capone, F. J.↗
NASA NTRS2003

AWS Figure of Merit (FOM) Developed Parameters from Static, Transonic Model Tests

This paper provides an approach to answer the question of whether one can rely solely on static data taken during a transonic model test to provide the certainty needed that a new aircraft will or will not have Abrupt Wing Stall (AWS) events during its flight operations. By comparing traditional- and alternate-static-Figures of Merit (FOMs) with the Free-To-Roll (FTR) response data, a rational basis for assessing the merits of using standard testing techniques for the prediction of AWS events has been established. Using the FTR response data as a standard, since these results compare well with flight, the conclusion from this study is that neither traditional nor alternate FOMs can be trusted to provide an indication as to whether a configuration will or will not have AWS tendencies. Even though these FOMs may flag features which have a high degree of correlation with the FTR response data, there are as many or more of these FOM flagged features which do not correlate. Thus, one needs to use the FTR rig to assess AWS tendencies on new configurations.

Lamar, J. E.↗
NASA NTRS1987

Parametric study of single expansion ramp nozzles at subsonic/transonic speeds

The Langley Research Center has conducted a parametric investigation to determine the aeropropulsive characteristics of single expansion ramp nozzles (SERN). The SERN is a nonaxisymmetric, variable-area, internal/external expansion exhaust nozzle. Internal nozzle parameters that were varied included upper ramp length, ramp chordal angle, lower flap length, flap angle and the axial and vertical locations of nozzle throat. Convergent-divergent and convergent nozzles were included in this investigation which was conducted in the Langley 16-Foot Transonic Tunnel at Mach numbers from 0.6 to 1.2 and at nozzle pressure ratios up to 12.0.

Capone, F. J.↗
NASA NTRS1986

Effect of port corner geometry on the internal performance of a rotating-vane-type thrust reverser

An investigation has been conducted in the static-test facility of the Langley 16-Foot Transonic Tunnel to determine the effects of reverser port geometry on the internal performance of a nonaxisymmetric rotating-vane-type thrust reverser. Thrust reverser vane positions representing a spoiled-trust (partially deployed) position and a full-reverse-thrust (fully deployed) position were tested with each port geometry variable. The effects of upstream port corner radius and wall angle on internal performance were determined. In addition, the effect of the length of a simulated cooling liner (blunt-base step) near the reverser port entrance was investigated; five different lengths were tested. All tests were conducted with no external flows, and nozzle pressure ratio was varied from 1.2 to 5.0.

Berrier, B. L.↗
NASA NTRS1986

Multiaxis aircraft control power from thrust vectoring at high angles of attack

Extensive research programs conducted at the Langley Research Center have shown that thrust vectoring can be provided by multifunction (nonaxisymmetric) nozzles. Most of this research has been conducted on pitch vectoring at both static and forward flight conditions. Recent efforts have been aimed at evaluating yaw vectoring concepts at static (wind off) conditions. This paper summarizes results for three different twin-engine fighter configurations tested over a Mach number range of 0.15 to 2.47 at angles of attack up to 35 deg. The objective of these investigations was to determine the multiaxis control power characteristics provided by thrust vectoring. All three configurations employed two-dimensional convergent-divergent nozzles which provided pitch vectoring by differential deflection of the upper and lower nozzle divergent flaps. Three different means of yaw vectoring were tested: (1) a translating nozzle sidewall; (2) yaw flaps located in the nozzle sidewalls; and (3) canted nozzles. These investigations were conducted in the Langley 16-Foot Transonic Tunnel and the Lewis 10x10-Foot Supersonic Tunnel. Longitudinal and direction control power from thrust vectoring was greater than that provided by aerodynamic control effectors at low speed or at high angles of attack.

Capone, F. J.↗
NASA NTRS1986

Aerodynamic Characteristics of a Supersonic Fighter Aircraft Model at Mach 0.40 to 2.47

The aerodynamic characteristics of an advanced twin-engine fighter aircraft designed for supersonic cruise have been studied in the Langley 16-Foot Transonic Tunnel and the Lewis 10- by 10-Foot Supersonic Tunnel. The objective of this investigation was to establish an aerodynamic data base for the configuration with flow-through nacelles and representative inlets. The use of a canard for trim and the effects of fairing over the inlets were assessed. Comparisons between experimental and theoretical results were also made. The theoretical results were determined by using a potential vortex lift code for subsonic speeds and a linear aerodynamic code for supersonic speeds. This investigation was conducted at Mach numbers from 0.40 to 2.47, at angles of attack from 0 deg to about 20 deg, and at inlet capture ratios of about 0.5 to 1.4.

Capone, F. J.↗
NASA NTRS1984

Interference effects of thrust reversing on horizontal tail effectiveness of twin-engine fighter aircraft at Mach numbers from 0.15 to 0.90

An investigation was conducted in the Langley 16 foot Transonic Tunnel to determine the interference effects of thrust reversing on horizontal tail effectiveness of a twin engine, general research fighter model at approach and in-flight speeds. Twin vertical tails at three longitudinal locations were tested at a cant angle of 0 deg. One configuration was also tested at a cant angle of 20 deg. Two nonaxisymmetric nozzle reverser concepts were studied. Test data were obtained at Mach numbers of 0.15, 0.60, and 0.90 and at angles of attack from -3 to 9 deg. Nozzle pressure ratios varied from jet off to 7.0, depending upon Mach number. At landing approach speed (Mach number 0.15), thrust reverser operation usually resulted in large variations (up to 70% increase) in horizontal tail effectiveness as nozzle pressure ratio was varied at zero angle of attack or as angle of attack was varied at constant nozzle pressure ratio. There was always a decrease in effectiveness at Mach numbers of 0.60 and 0.90 as a result of reverser operation.

Capone, F. J.↗
NASA NTRS1984

Subsonic/supersonic aerodynamic characteristics for a tactical supercruiser

A series of cooperative NASA-Langley/Boeing experimental investigations have been conducted to determine the aeropropulsive characteristics of an advanced tactical fighter designed for supersonic cruise. These investigations were conducted in the Langley 16-Foot Transonic and Lewis 10 x 10-Foot Supersonic Wind Tunnels at Mach numbers from 0.60 to 2.47. This fighter is a Mach 2.0, 49,000 pound class vehicle that features a close-coupled canard and underwing propulsion units that utilize multifunction two-dimensional exhaust nozzles. Tests were conducted to determine the basic aerodynamic characteristics of the configuration with flow-through nacelles in which the spillage effects of representative inlets were measured. The effects of thrust-induced forces on overall aerodynamic performance were evaluated with a series of multifunction nozzles installed on air-powered nacelles. An axisymmetric nozzle configuration was also tested to obtain comparative aeropropulsive performance. Trim aerodynamic characteristics for the flow-through and powered configurations and the effect of thrust vectoring at subsonic speeds are presented.

Capone, F. J.↗
NASA NTRS1984

Aeropropulsive characteristics of nonaxisymmetric-nozzle thrust reversers at Mach numbers from 0 to 1.20

An investigation was conducted in the Langley 16-Foot Transonic Tunnel to determine the performance of nonaxisymmetric-nozzle thrust reversers installed on a generic twin-engine fighter aircraft model. Test data were obtained at static conditions and at Mach numbers from 0.15 to 1.20 with jet exhaust simulated by high pressure air. Results showed that reverse-thrust levels of greater than 50 percent at static conditions and greater than 30 percent at in-flight conditions could be achieved. Internal reverser-port passage length was found to be very important in improving reverser performance. Increasing the reverser-port passage length improved reverse-thrust performance by as much as 28 percent at static conditions and by as much as 17 percent at Mach 1.20.

Carson, G. T., Jr.↗
NASA NTRS1983

Effects of varying podded nacelle-nozzle installations on transonic aeropropulsive characteristics of a supersonic fighter aircraft

The aeropropulsive characteristics of an advanced twin engine fighter designed for supersonic cruise was investigated in the 16 foot Transonic Tunnel. The performance characteristics of advanced nonaxisymmetric nozzles installed in various nacelle locations, the effects of thrust induced forces on overall aircraft aerodynamics, the trim characteristics, and the thrust reverser performance were evaluated. The major model variables included nozzle power setting; nozzle duct aspect ratio; forward, mid, and aft nacelle axial locations; inboard and outboard underwing nacelle locations; and underwing and overwing nacelle locations. Thrust vectoring exhaust nozzle configurations included a wedge nozzle, a two dimensional convergent divergent nozzle, and a single expansion ramp nozzle, each with deflection angles up to 30 deg. In addition to the nonaxisymmetric nozzles, an axisymmetric nozzle installation was also tested. The use of a canard for trim was also assessed.

Capone, F. J.↗
NASA NTRS1983

Aeropropulsive characteristics of twin single-expansion-ramp vectoring nozzles installed with forward-swept wings and canards

The Langley 16 foot transonic tunnel was used to determine the aeropropulsive characteristics of twin single-expansion-ramp vectoring nozzles installed in a wing-body configuration with forward-swept wings. The configuration was tested with and without fixed canards. The test conditions included free-stream Mach numbers of 0.60, 0.90, and 1.20. The model angle of attack ranged from -2 deg to 14 deg; the nozzle pressure ratio ranged from 1.0 (jet off) to 9.0. The Reynolds number based on the wing mean aerodynamic chord varied from 3.0 x 10 to the 6th power to 4.8 x 10 to the 6th power, depending on Mach number. Aerodynamic characteristics were analyzed to determine the effects of thrust vectoring and the canard effects on the wing-afterbody-nozzle and the wing-afterbody portions of the model. Thrust vectoring had no effect on the angle of attack for the onset of flow separation on the wing but resulted in reduced drag at angle-of-attack values above that required for wing flow separation. The canard was found to have little effect on the thrust-induced lift resulting from vectoring, since canard effects occurred primarily on the wing.

Mason, M. L.↗
NASA NTRS1983

Effect of thrust vectoring and wing maneuver devices on transonic aeropropulsive characteristics of a supersonic fighter

The aeropropulsive characteristics of an advanced fighter designed for supersonic cruise were determined in the Langley 16-Foot Transonic Tunnel. The objectives of this investigation were to evaluate the interactive effects of thrust vectoring and wing maneuver devices on lift and drag and to determine trim characteristics. The wing maneuver devices consisted of a drooped leading edge and a trailing-edge flap. Thrust vectoring was accomplished with two dimensional (nonaxisymmetric) convergent-divergent nozzles located below the wing in two single-engine podded nacelles. A canard was utilized for trim. Thrust vector angles of 0 deg, 15 deg, and 30 deg were tested in combination with a drooped wing leading edge and with wing trailing-edge flap deflections up to 30 deg. This investigation was conducted at Mach numbers from 0.60 to 1.20, at angles of attack from 0 deg to 20 deg, and at nozzle pressure ratios from about 1 (jet off) to 10. Reynolds number based on mean aerodynamic chord varied from 9.24 x 10 to the 6th to 10.56 x 10 to the 6th.

Capone, F. J.↗
NASA NTRS1983

Thrust reversing effects on horizontal tail effectiveness of twin-engine fighter aircraft

The Langley Research Center has conducted an experimental program to determine the interference effects of thrust reversing on horizontal tail effectiveness of a twin engine, general research fighter model at approach (Mach number 0.15) and in-flight (Mach number 0.60 and 0.90) speeds. Twin vertical tails were tested at three longitudinal locations. Two nonaxisymmetric nozzle reverser concepts were studied. The effects of thrust reversing on horizontal tail effectiveness were found to be very dependent upon vertical tail locations. At approach speeds thrust reverser operation usually resulted in large variations in horizontal tail effectiveness as either nozzle pressure ratio or model angle of attack was varied. Either increases or decreases in tail effectiveness ocurred due to reverse operation depending upon tail location. At in-flight conditions there were always decreases in tail effectiveness due to reverser operation regardless of vertical tail location.

Capone, F. J.↗
NASA NTRS1982

Aeropropulsive characteristics of Mach numbers up to 2.2 of axisymmetric and nonaxisymmetric nozzles installed on an F-18 model

An investigation to determine the aeropropulsive characteristics of nonaxisymmetric nozzles on an F-18 jet effects model was conducted in the Langley 16-foot transonic tunnel and the AEDC 16-foot supersonic wind tunnel. The performance of a two dimensional convergent-divergent nozzle, a single expansion ramp nozzle, and a wedge nozzle was compared with that of the baseline axisymmetric nozzle. Test data were obtained at static conditions and at Mach numbers from 0.60 to 2.20 at an angle of attack of 0 deg. Nozzle pressure ratio was varied from jet-off to about 20.

Capone, F. J.↗
NASA NTRS1981

Thrust reversing effects on twin-engine aircraft having nonaxisymmetric nozzles

The effects of thrust reversing on stability, control and vertical tail loads of advanced fighter aircraft are reviewed. Several static test stand and wind tunnel investigations of nonaxisymmetric nozzles with integral thrust reversers are presented, and it is found that base drag on the aft face of reverser panels of blockers provides a significant contribution to in-flight thrust reverser performance. The location of tail surfaces relative to the thrust reverser has significant impact on control surface effectiveness, and depending on thrust reverser location, large vertical tail side force can result from the use of in-flight thrust reversers. It is concluded that highly effective nonaxisymmetric nozzle reversers can be designed to achieve a 50% static reverse thrust.

Capone, F. J.↗
NASA NTRS1981

Effect of simulated in-flight thrust reversing on vertical-tail loads of F-18 and F-15 airplane models

Investigations were conducted in the Langley 16-Foot Transonic Tunnel to provide data on a 0.10-scale model of the prototype F-18 airplane and a 0.047-scale model of the F-15 three-surface configuration (canard, wing, and horizontal tails). Test data were obtained at static conditions and at Mach numbers from 0.6 to 1.2 over an angle-of-attack range from 2 deg to 15 deg. Nozzle pressure ratio was varied from jet off to about 8.0.

Bare, E. A.↗