Accelerated Fuel Qualification: BISON Validation to In-Situ Cladding Burst Test
Explore the source record for details and available documents.
Engineering topics
Publications and source records attributed to Capps, Nathan.
Explore the source record for details and available documents.
Burst testing has long been a relied-on method for assessing fuel cladding materials in light-water reactoraccident scenarios. However, burst testing historically provided minimal in-situ observations beyond a few thermocouple readings, pressure from transducers, and post-test deformation measurements. Acquisition of full cladding thermomechanical data throughout a burst test would be invaluable to fuel system qualification, material model development and fuel performance code validation, such as the BISON fuel performance code. Recently, methodologies for simultaneously applying 2-dimensional digital image correlation and infrared thermography techniques to quantify the relationship between temperature, internal cladding pressure, and deformation during burst testing were developed. This work details results from the application of these techniques to burst testing of Zircaloy-4 cladding segments subjected to loss-of-coolant accident transients in an air environment. Two types of tests were performed with: (a) cladding segments connected to a fixed pressure reservoir as well as (b) closed systems where internal pressure increased during transients. In-situ thermomechanical measurements including strain and thermal gradient data are presented, demonstrating the effectiveness of applying combined surface measurement techniques to burst testing
Explore the source record for details and available documents.
Explore the source record for details and available documents.
The development and verification of nuclear fuel-cladding performance codes require extensive testing to establish empirical correlations, necessitating more accelerated testing methods that can replace large validation studies. Here, in the present work, a technique was developed and implemented to experimentally quantify the relationship between temperature, cladding internal pressure, and strain in-situ during a burst test, with the specific aim of generating data for code validation and model refinement. Digital image correlation was used to measure hoop, axial, and radial strain, and infrared thermography to quantify axial temperature gradients. Several key experimental modifications to traditional LOCA burst testing were necessary, but are shown to effectively have little impact on burst temperatures. The time/temperature dependent pressure and time/spatially dependent thermal gradient data were used with BISON to simulate cladding burst and strain rates. Although the measured DIC strains reach appreciable amounts at slightly lower temperatures than BISON simulated strains, there is good agreement between the measured and simulated strains in terms of magnitude and rates leading up to burst. However, in the few seconds prior to and during burst, the BISON simulated strains are significantly lower than the measured strains, indicating the potential for model improvement. The combined experiment and simulation technique may be applied to any new cladding concept to accelerate fuel qualification.
The US nuclear energy industry is investigating strategies that further reduce the cost of energy production by using its existing fleet of nuclear generating stations. Most nuclear power plant operating costs are associated with purchasing fresh fuel assemblies or the efficiency of the reactor core design. Material costs are typically beyond the operator’s control; however, the core design optimizations offer potential operational savings. The core design envelope available to operators is constrained by two primary regulatory criteria: an enrichment limit of 5% 235 U and a burnup limit of 62 GWD/tU. These constraints have resulted in renewed efforts by the nuclear industry to pursue extending the peak rod-average burnup beyond 62 GWd/tU. This effort will likely require additional safety analyses beyond what is currently accepted by the US Nuclear Regulatory Commission. The purpose of this work is to demonstrate a best estimate plus uncertainty pin-by-pin high-burnup loss of coolant accident analysis technique to assess full-core high-burnup fuel fragmentation, relocation, and dispersal (FFRD) and identify approaches for minimizing or potentially mitigating FFRD through core design optimizations.
This report presents the results from the microstructural examination of high burnup UO 2 under pre- and post- loss of coolant accident (LOCA) conditions. The work in this report builds and expands upon work previously conducted on high burnup UO 2 fuel at Oak Ridge National Laboratory (ORNL). This work investigates the microstructural evolution that occurs during steady state irradiation of UO 2 , particularly in high burnup fuel. Several high burnup fuel samples were available from historic fuel shipments to ORNL. Microstructural characterization will aid in understanding why the fuel is susceptible to fuel fragmentation and support future work to investigate the formation mechanisms of certain features that form under irradiation. High burnup UO 2 microstructural data is also needed to improve constitutive models intended to predict high burnup fuel fragmentation (HBFF). This report summarizes the microstructural evaluation of these fuel samples to interpret and analyze high burnup fuel microstructures.
This document provides a detailed description of comments and responses, to the Advanced Fuel Campaign (AFC) loss-of-coolant accident (LOCA) experiment plan draft document shared in April 2022. Comments were provided from reviewers from U.S. nuclear fuel vendors, the Electric Power Research Institute (EPRI), the U.S. Nuclear Regulatory Commission (NRC), and the U.S. Department of Energy (DOE) all provided comments after solicitation. All comments have been carefully considered and responded to accordingly. Editorial and clarification comments are excluded from this writeup, but all have been addressed directly in the text of the revised plan document.
The Transient Reactor Test Facility (TREAT) loss-of-coolant (LOC) and highburnup (HBu) experiment series, along with the Severe Accident Test Station (SATS) HBu experiment series, are integral LOC accident (LOCA) experiments planned under the Department of Energy (DOE) Advanced Fuels Campaign (AFC) program, which aims to support burnup extension needs by addressing identified R&D priorities in order to achieve an improved understanding of fuel fragmentation, relocation, and dispersal (FFRD) of HBu fuel during LOCA events. Priorities have been identified by the Electric Power Research Institute (EPRI)’s Collaborative Research on Advanced Fuel Technologies (CRAFT) Fuel Performance and Testing Technical Experts Group (FPTTEG). The data produced under this plan will be used to further validate and confirm existing models and inform future R&D and model development. The experimental program was specifically developed to address data gaps and opportunities identified via detailed review of the existing public knowledge base on LOCA FFRD, as well as reviewing specific experimental development activities regarding prototypic LOCA conditions for light-water reactor (LWR) systems. The test program relies on a unique combination of in- and out-of-pile experimental approaches to provide a clear tieback to the existing integral and semi-integral LOCA experiment database, using state-of-the-art facilities. More importantly, the program will systematically investigate the impacts of prototypic HBu fuel/cladding thermomechanical behaviors under postulated LWR LOCA conditions not yet fully investigated. These conditions correspond with prototypic decay-energy heatup (DEH) and stored-energy heatup (SEH) conditions. First, TREAT’s unique capability will enable the first evaluation of the impact of SEH conditions on HBu fuels. The test program will emphasize the development of an improved mechanistic understanding of key phenomena through independent experimental systems, development of a database to support fuel performance modeling tools, world-leading advanced materials characterization, and the most advanced approach to in situ diagnostics ever deployed to evaluate FFRD. The results will represent a significant leap forward in evaluating prototypic conditions and novel data to support modeling development and validation, as well as to inform the technical basis for LOCA-induced FFRD.
The process to develop and qualify nuclear fuels for commercial nuclear application requires fundamental material development, characterization, and design; out-of-pile testing on unirradiated materials; integral fuel rod irradiations, testing, and post irradiation examinations (PIEs); and transient analyses. The historical approach depends on the generation of large empirical datasets and series of integral fuel rod irradiations, and this approach ultimately takes approximately 20 years—or sometimes longer—to acquire data through extensive sequential testing. Thus, the qualification and eventual deployment of new fuel systems constitute a long and drawn-out process. However, recent technological advancements have provided researchers the opportunity to perform out-of-cell, in-situ measurements to assess material performance for the duration of the experiment. One such example of this capability is the use of digital image coordination and thermal imaging to assess Zircaloy cladding performance under a simulated loss-of-coolant accident (LOCA) transient condition. In general, the in-situ measurements provide high-fidelity strain, strain rates, and temperature surface maps. This is critical for the United States nuclear industry, which is actively developing a technical basis to support extending the peak rod average burnup from 62 to ~75 GWd/tU and the deployment of accident-tolerant fuel. However, the Nuclear Regulatory Commission, through their research information letter, outlined a number of technical issues for the industry to address before extending burnup. One topic of specific interest is understanding the cladding balloon and rupture geometry during the LOCA heatup phase. Leveraging these advanced in-situ capabilities, this work intends to use insitu data generated from a simulated LOCA in the Severe Accident Test Station at Oak Ridge National Laboratory to better understand high-temperature creep and its impact on Zircaloy balloon and rupture performance. This work used the BISON fuel performance code to compare BISON’s high-temperature creep model predictions to in-situ data and identify limitations and gaps within the model. Additionally, BISON will subsequently be used to simulate relevant high-burnup LOCA tests. The results will be analyzed and compared to the available post-test data in a manner consistent with the approach outlined in the Nuclear Regulatory Commission research information letter.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Of the near-term accident-tolerant fuel concepts identified, chromium coatings have been shown to slow cladding oxidation without altering fuel system geometry or greatly affecting neutronic performance. To identify how coated cladding tubes perform under high-temperature accident conditions, pressurized-tube burst tests were conducted in the Severe Accident Test Station at Oak Ridge National Laboratory. To analyze how the coating affects cladding behavior, coated and uncoated cladding burst tests were simulated by using the BISON fuel performance code. Thermocouple data from these tests were fit into axial and azimuthal profiles and combined to generate 3D cladding surface temperatures, and pressure transducer data were compared until cladding failure. Additionally, the cladding temperatures at failure and the internal gas pressure evolution show relatively good agreement between the simulation and experiment results. Simulations were then extrapolated to demonstrate the coatings effectiveness to increasing the cladding burst temperature by using a parametric evaluation of the initial tube gas pressure. This work demonstrates the possibility of an increased cladding failure margin under transient conditions due to the addition of chromium coating, and more pertinently, an increased cladding failure margin from more accurate experimental characterization.
This report is an update on the progress made towards utilizing in-situ methods to observe and quantify Zry-4 deformation behavior during burst testing. A heavily modified burst test was developed that allows both digital image correlation and infrared thermography to be utilized during testing to quantify strain and axial thermal gradient data during burst. A variety of tests ranging from 6.2-15.9 MPa internal pressure and utilizing both constant and transient pressure conditions were conducted and presently reported on. The test modifications, which are detailed extensively in a previous report, are effectively found to have no discernible impact on burst temperatures when compared to historical Zircaloy burst data. To support future modeling studies, the IR thermography data was used to approximate the thermal gradient down the axial length at burst for all the claddings. Then, DIC is first correlated to thermocouple temperature for a 10.3 MPa Transient pressure test, and then DIC correlated to IR thermal gradient data down the axial length of a 8.2 MPa Transient pressure test at several points.
Fuel fragmentation, relocation, and dispersal are some of the largest issues remaining in the nuclear industry before rod-average burnup can be increased beyond 62 GWd/tU. The issue is primarily related to the potential for fuel to be dispersed into the reactor primary system, which may increase public risk. One way to prevent dispersal is to avoid cladding burst. The objective of this work is to support the high burnup safety case by evaluating cladding burst under high-burnup, full-length fuel rods and to identify uncertainties that could improve model predictions. The results of this analysis will evaluate realistic, prototypic loss-of-coolant accident (LOCA) conditions; support future cladding burst test designs; and inform the development of mechanistic material models. Realistic high-burnup operating conditions were implemented in the BISON fuel performance code to simulate steady-state and LOCA transient fuel rod evolution to the point at which cladding burst occurred. Parametric studies are performed to assess code response to changes in rod internal pressures and heating rates. Results were compared with simulated LOCA experiments to identify inconsistencies between commercial fuel rod analysis and experimental validation. The representative full-length fuel rod LOCA simulation results did not agree with cladding burst tests. Cladding burst tests indicated burst occurring well below (100–150 °C) those calculated in the full-length fuel rod LOCA analysis. Further investigation indicated that the cladding burst tests do not appear to be representative for full-length fuel rods. The inconsistency investigated in this work showed that the differences between the BISON simulation and the experiment's cladding burst conditions arise from an incomplete characterization of the cladding surface temperature, detailed rodlet characterization, lack of cladding strain measurements, and uncertainty in the cladding creep and failure models.
During a loss of coolant accident (LOCA), there is the possibility of nuclear fuel rods to undergo a three step process known as fuel fragmentation, relocation, and dispersal (FFRD). The chance of FFRD occurring increases as the fuel burnup increases. To support the nuclear industry's desire to increase the discharge burnup of nuclear fuels in light water reactors (LWRs) it is imperative to understand the mechanisms driving the evolution of FFRD. In this work, a multiscale modeling modeling approach is used to garner insight into underlying mechanisms leading to the ne fragmentation (also known as pulverization) of nuclear fuel during a LOCA. This report includes a summary of the atomistic and phase-field studies to develop a new pulverization criterion for use in the engineering scale Bison fuel performance code. Details are also provided on cladding modeling improvements related to hydrogen/hydride embrittlement and damage, and anisotropic thermal creep. The new models are used on the existing integral and separate effects LOCA validation cases available in Bison.
In 2012 the U.S. Congress directed the Department of Energy’s (DOE) Office of Nuclear Energy to give priority to developing enhanced fuels and cladding for light water reactors to improve safety in the event of accidents in the reactor or spent fuel pools. DOE developed a plan with a goal to insert a Lead Test Assembly (LTA) into a commercial light water reactor by the end of FY 2022. Three of the leading commercial nuclear fuel vendors, in concert with several participating commercial nuclear utilities, are now seriously engaged in this initiative and have exceeded initial expectations by having met DOE’s goal this year, three years ahead of schedule. The early successes of the ATF program are due in part to a strong collaboration by the DOE national laboratories with both commercial nuclear fuel vendors and the U.S. Nuclear Regulatory Commission. This undertaking has recently been expanded to incorporate an effort to extend burnup from the current U.S. regulatory limit of 62 GWD/MTU and increase enrichment as necessary to support routine utilization of fuel at >75 GWD/MTU. This effort provides a critical economic incentive to accelerate the deployment of ATF technologies. This paper reviews the DOE-sponsored, industry-led ATF concepts currently under development and highlights the contributions made by the DOE laboratories in support of these ATF concepts, including: 1) steady-state irradiation testing in the Advanced Test Reactor (ATR) and High Flux Isotope Reactor (HFIR); 2) transient irradiation testing in the Transient Reactor Test Facility (TREAT); 3) fabrication process development and characterization of high density fuels, Cr-coated Zry cladding, FeCrAl cladding, and SiC cladding; and 4) post-irradiation examination of lead test rods irradiated in commercial reactors.
During a loss-of-coolant accident (LOCA), it is possible for nuclear fuel rods to undergo a three-step process known as fuel fragmentation, relocation, and dispersal (FFRD). The chance of FFRD occurring increases as the fuel burnup increases. To support the nuclear industry's desire to increase the discharge burnup of nuclear fuels in light-water reactors (LWRs), it is imperative to understand the mechanisms driving the evolution of FFRD. In this work, a multiscale modeling approach is used to garner insight into underlying mechanisms leading to the fine fragmentation (also known as pulverization) of nuclear fuel during a LOCA. This report includes a summary of the atomistic and phase-field studies to develop a new pulverization criterion for use in the engineering-scale Bison fuel performance code. Details are also provided on cladding model improvements related to hydrogen/hydride embrittlement and damage and anisotropic thermal creep. The new models are used on the existing integral and separate effects LOCA validation cases available in Bison.