Search NASA⌕ Search

Engineering topics

Caradonna, F. X.

Publications and source records attributed to Caradonna, F. X..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

A study of blade-vortex interaction aeroacoustics utilizing an independently generated vortex

This paper presents results from an experimental study of rotor blade-vortex interaction (BVI) aerodynamics and acoustics. The experiment utilized an externally generated vortex interacting with a two-bladed rotor operating at zero thrust to minimize the influence of the rotor's own wake. The rotor blades were instrumented with a total of 60 absolute pressure transducers at three spanwise and ten chordwise stations on both the upper and lower surfaces. Acoustic data were obtained with fixed near-field microphones as well as a movable array of far-field microphones. The test was carried out in the acoustically treated test section of the NASA Ames 80- by 120-foot Wind Tunnel. Several parameters which influences BVI, such as vortex-rotor separation distance, vortex strength, and vortex sense (swirl direction), as well as rotor tip Mach number and advance ratio, were varied. Simultaneous measurements were obtained of blade surface pressure distributions, near-field acoustics, and far-field acoustics during the vortex-blade encounters.

Kitaplioglu, C.↗
NASA NTRS1993

Free-wake computation of helicopter rotor flowfields in forward flight

A new method has been developed for computing advancing rotor flows. This method uses the Vorticity Embedding technique, which has been developed and validated over the last several years for hovering rotor problems. In this work, the unsteady full potential equation is solved on an Eulerian grid with an embedded vortical velocity field. This vortical velocity accounts for the influence of the wake. Dynamic grid changes that are required to accommodate prescribed blade motion and deformation are included using a novel grid blending method. Free wake computations have been performed on a two-bladed AH-1G rotor at low advance ratios including blade motion. Computed results are compared with experimental data. The sudden variations in airloads due to blade-vortex interactions on the advancing and retreating sides are well captured. The sensitivity of the computed solution to various factors like core size, time step and grids has been investigated. Computed wake geometries and their influence on the aerodynamic loads at these advance ratios are also discussed.

Ramachandran, K.↗
NASA NTRS1992

The appliation of potential CFD methods to helicopter hover flows

Fixed-wing code development is now aimed primarily at the solution of problems dominated by separation--based on the assumptions that the ability to solve such problems implies the ability to solve all other problems and that present inviscid method are already adequate for most other problems. Neither of the above assumptions are correct for rotary wing problems. This is because of the unique and overriding importance of wake modeling to rotor problems and also due to the well-known numerical diffusion problems which convectional Eulerian Computational fluid dynamics (CFD) method encounter when called on to convect strong vortical regions for long distances. The need for accurate wake analyses is probably the most fundamental difference between rotory and fixed-wing aerodynamics. In addition, rotary wing complexity requires a much more intimate relationship between test and analysis than is common in fixed-wing work. With these issues in mind, this paper will review some of our recent experience in using a unique-Eulerian-Lagrangian Computational fluid dynamics (CFC) method for the solution of a critical rotor-wake problem--the prediction of hover performance.

Caradonna, F. X.↗
NASA NTRS1991

The computation and validation of hovering rotor performance

Recent experience with the HELIX-I code is presented, and its ability to predict the flow and performance of both conventional rotors and the unconventional anhedral parabolic tip rotor utilized on the Super Puma MK2 is described. HELIX-I is a standard full-potential rotor code having the ability to efficiently predict the detailed flow on a rotor blade, including 3D, transonic, and weak viscous effects (using appropriate boundary layer analyses). The resulting code is the first full-potential CFD code with the ability to model free wake convection and the first CFD code of any type to predict hover performance.

Mba, M. N.↗
NASA NTRS1991

Experimental and computational studies of hovering rotor flows

HELIX-I, an essentially standard full-potential CFD helicopter rotor code, is unique in its use of the Clebisch kinematical flow description to specify a freely convecting wake and its capacity for predicting hover performance. A study is presently performed to assess the method's sensitivity to grids and solution-starting techniques. The effects of these parameters on thrust, power, load distribution, and wake geometry are ascertained and compared with an extensive rotor data base. The use of a fairly accurate starting solution yields no obvious advantage over the use of a novel starting method which employs a succession of diminishing artificial flows.

Nsi Mba, M.↗
NASA NTRS1990

The application of CFD to rotary wing flow problems

Rotorcraft aerodynamics is especially rich in unsolved problems, and for this reason the need for independent computational and experimental studies is great. Three-dimensional unsteady, nonlinear potential methods are becoming fast enough to enable their use in parametric design studies. At present, combined CAMRAD/FPR analyses for a complete trimmed rotor soltution can be performed in about an hour on a CRAY Y-MP (or ten minutes, with multiple processors). These computational speeds indicate that in the near future many of the large CFD problems will no longer require a supercomputer. The ability to convect circulation is routine for integral methods, but only recently was it discovered how to do the same with differential methods. It is clear that the differential CFD rotor analyses are poised to enter the engineering workplace. Integral methods already constitute a mainstay. Ultimately, it is the users who will integrate CFD into the entire engineering process and provide a new measure of confidence in design and analysis. It should be recognized that the above classes of analyses do not include several major limiting phenomena which will continue to require empirical treatment because of computational time constraints and limited physical understanding. Such empirical treatment should be included, however, into the developing CFD, engineering level analyses. It is likely that properly constructed flow models containing corrections from physical testing will be able to fill in unavoidable gaps in the experimental data base, both for basic studies and for specific configuration testing. For these kinds of applications, computational cost is not an issue. Finally, it should be recognized that although rotorcraft are probably the most complex of aircraft, the rotorcraft engineering community is very small compared to the fixed-wing community. Likewise, rotorcraft CFD resources can never achieve fixed-wing proportions and must be used wisely. Therefore the fixed-wing work must be gleaned for many of the basic methods.

Caradonna, F. X.↗
NASA NTRS1990

The free-wake computation of rotor-body flows

In this paper a method is described for predicting the compressible, free-wake, flow about a lifting rotor-body configuration. The method is an extension of a unique vorticity embedded full-potential method used to calculate free-wake rotor hover performance. An unusual feature of this method is that it obviates the requirement for multiple grids to treat the rotor-body problem. The approach used to treat the body is similar to that used to include the rotor wake in the full potential calculation. The body is modeled as a structured circulation sheet and the strength of this sheet is determined in an iterative manner. Initially the method is tested to compute the flow past simple isolated bodies like cylinders and spheres. After a comparison of these simple computations with exact solutions this procedure is included into the HELIX-I, free-wake rotor code, to compute the flow around a rotor mounted on a large whirl tower. The effects of the tower on rotor wake geometry and load distribution are presented.

Ramachandran, K.↗
NASA NTRS1990

Computational Fluid Dynamics For Helicopters

Powerful computer codes undergoing development. Report reviews development of computational fluid dynamics (CFD) for prediction of airflow around rotary wings of helicopters. Reviews progress in following endeavors: Prediction and verification of flows under various operating conditions; calculation of interactions between rotor blades and vortexes; analysis of viscous, transonic flows about airfoils; and study of formation of vortexes at tips of rotors.

Caradonna, F. X.↗
NASA NTRS1989

The free-wake prediction of rotor hover performance using a vortex embedding method

A method is developed to predict the rotor hover performance. This method solves the compressible mass conservation equation much like current full potential codes and can therefore predict the transonic flows on a rotor. However, the newly developed approach also allows for the free convection of shed vorticity and permits the computation of the entire hover wake system. The method uses a vortex embedding scheme in potential flow and has been implemented in a computer code, HELIX -I. To predict power we implement a simple boundary layer and two different induced-drag integration schemes. The induced-drag is obtained from surface pressure integration and an energy flux integral. Comparisons between computations and experiment show good agreement for the prediction of power polars, surface pressure distribution, and tip vortex geometry.

Ramachandran, K.↗
NASA NTRS1989

Application of transonic flow analysis to helicopter rotor problems

The transonic aspect of helicopter flow analysis is addressed. The equations of motion and their implementations are examined, and the computation of real rotor flows is considered. Nonlifting rotor flows, high-speed hover, high advance ratio lifting rotor flows, and strong blade/vortex interaction computations are discussed.

Caradonna, F. X.↗
NASA NTRS1988

The development of CFD methods for rotor applications

The optimum design of the advancing helicopter rotor for high-speed forward flight always involves a tradeoff between transonic and stall limitations. However, the preoccupation of the rotor industry was primarily concerned with stall until well into the 1970s. This emphasis on stall resulted from the prevalent use of low-solidity rotors with rather outdated airfoil sections. The use of cambered airfoil sections and higher-solidity rotors substantially reduced stall and revealed the advancing transonic flow to be a more persistent limitation to high-speed rotor performance. Work in this area was spurred not only by operational necessity but also by the development of a tool for the prediction of these flows (the method of computational fluid dynamics). The development of computational fluid dynamics for these rotor problems was a major Army and NASA achievement. This work is now being extended to other rotor flow problems. The developments are outlined.

Caradonna, F. X.↗
NASA NTRS1988

An experimental study of rotor-vortex interactions

A scheme for investigating general blade/vortex interactions (BVIs) has been used to obtain an unusual body of data. The scheme involves locating a vortex generator upstream of a nonlifting rotor so that the vortex interacts with the rotor at any desired forward azimuth. Parallel BVIs produced by this external vortex generator are shown to be nearly identical to those produced by the rotor alone operating in a normal descent mode. The test delineates various generic features of parallel and oblique BVIs. However, the dominant feature is the leading-edge pressure pulse. The effects of blade/vortex angle, and proximity (including head-on interactions) on this pulse are discussed. The effect of Mach number on the leading edge pressure variation is shown to be small even for supercritical interactions.

Caradonna, F. X.↗
NASA NTRS1986

Full potential modeling of blade-vortex interactions

A comparison is made of four different models for predicting the unsteady loading induced by a vortex passing close to an airfoil. (1) The first model approximates the vortex effect as a change in the airfoil angle of attack. (2) The second model is related to the first but, instead of imposing only a constant velocity on the airfoil, the distributed effect of the vortex is computed and used. This is analogous to a lifting surface method. (3) The third model is to specify a branch cut discontinuity in the potential field. The vortex is modeled as a jump in potential across the branch cut, the edge of which represents the center of the vortex. (4) The fourth method models the vortex expressing the potential as the sum of as known potential due to the vortex and an unknown perturbation due to the airfoil. The purpose of the current study is to investigate the four vortex models described above and to determine their relative merits and suitability for use in large three-dimensional codes.

Jones, H. E.↗
NASA NTRS1986

Full-potential modeling of blade-vortex interactions

A comparison is made of four different models for predicting the unsteady loading induced by a vortex passing close to an airfoil. (1) The first model approximates the vortex effect as a change in the airfoil angle of attack. (2) The second model is related to the first but, instead of imposing only a constant velocity on the airfoil, the distributed effect of the vortex is computed and used. This is analogous to a lifting surface method. (3) The third model is to specify a branch cut discontinuity in the potential field. The vortex is modeled as a jump in potential across the branch cut, the edge of which represents the center of the vortex. (4) The fourth method models the vortex expressing the potential as the sum of a known potential due to the vortex and an unknown perturbation due to the airfoil. The purpose of the current study is to investigate the four vortex models described above and to determine their relative merits and suitability for use in large three-dimensional codes.

Jones, H. E.↗
NASA NTRS1986

Numerical modeling of rotor flows with a conservative form of the full-potential equations

A computer program has been developed to solve a three-dimensional conservative formulation of the full-potential equation. Its ability to solve transonic, unsteady rotor flows is demonstrated by comparison to forward flight non-lifting pressure data at low to moderate advance ratios. A 'split potential' formulation has been added to the code which incorporates known vorticity fields into the full-potential calculation. Using this methodology, rotor wake contributions have been incorporated into the computer code. Pressure results are presented for lifting rotors in hover. These results are compared to experimental data as well as to other predictions.

Strawn, R. C.↗
NASA NTRS1986

A review of current finite difference rotor flow methods

Rotary-wing computational fluid dynamics is reaching a point where many three-dimensional, unsteady, finite-difference codes are becoming available. This paper gives a brief review of five such codes, which treat the small disturbance, conservative and nonconservative full-potential, and Euler flow models. A discussion of the methods of applying these codes to the rotor environment (including wake and trim considerations) is followed by a comparison with various available data. These data include tests of advancing lifting and nonlifting, and hovering model rotors with significant supercritical flow regions. The codes are also compared for computational efficiency.

Caradonna, F. X.↗
NASA NTRS1985

Finite-difference computations of rotor loads

The current and future potential of finite difference methods for solving real rotor problems which now rely largely on empiricism are demonstrated. The demonstration consists of a simple means of combining existing finite-difference, integral, and comprehensive loads codes to predict real transonic rotor flows. These computations are performed for hover and high-advanced-ratio flight. Comparisons are made with experimental pressure data.

Caradonna, F. X.↗