Engineering topics

Carignan, Craig R.

Publications and source records attributed to Carignan, Craig R..

7 records

NASA NTRS2012

Ground Simulation of an Autonomous Satellite Rendezvous and Tracking System Using Dual Robotic Systems

A hardware-in-the-loop ground system was developed for simulating a robotic servicer spacecraft tracking a target satellite at short range. A relative navigation sensor package "Argon" is mounted on the end-effector of a Fanuc 430 manipulator, which functions as the base platform of the robotic spacecraft servicer. Machine vision algorithms estimate the pose of the target spacecraft, mounted on a Rotopod R-2000 platform, relay the solution to a simulation of the servicer spacecraft running in "Freespace", which performs guidance, navigation and control functions, integrates dynamics, and issues motion commands to a Fanuc platform controller so that it tracks the simulated servicer spacecraft. Results will be reviewed for several satellite motion scenarios at different ranges. Key words: robotics, satellite, servicing, guidance, navigation, tracking, control, docking.

Trube, Matthew J.↗

NASA NTRS1991

Trajectory optimization for kinematically redundant arms

A review of local optimization methods for resolving joint configurations in underconstrained manipulation tasks is conducted. A new approach is developed for observing joint limits and avoiding obstacles during the trajectory planning. The methodology is used in a four-link arm example to avoid a workspace singularity and is compared with results using the extended Moore-Penrose technique. An alternative measure of arm 'manipulability' based directly on the rank of the Jacobian is also introduced.

Carignan, Craig R.↗

NASA NTRS1990

Adaptive tracking for complex systems using reduced-order models

Reduced-order models are considered in the context of parameter adaptive controllers for tracking workspace trajectories. A dual-arm manipulation task is used to illustrate the methodology and provide simulation results. A parameter adaptive controller is designed to track the desired position trajectory of a payload using a four-parameter model instead of a full-order, nine-parameter model. Several simulations with different payload-to-arm mass ratios are used to illustrate the capabilities of the reduced-order model in tracking the desired trajectory.

Carignan, Craig R.↗

NASA NTRS1990

Constrained trajectory optimization for kinematically redundant arms

Two velocity optimization schemes for resolving redundant joint configurations are compared. The Extended Moore-Penrose Technique minimizes the joint velocities and avoids obstacles indirectly by adjoining a cost gradient to the solution. A new method can incorporate inequality constraints directly to avoid obstacles and singularities in the workspace. A four-link arm example is used to illustrate singularity avoidance while tracking desired end-effector paths.

Carignan, Craig R.↗

NASA NTRS1989

An adaptive controller for enhancing operator performance during teleoperation

An adaptive controller is developed for adjusting robot arm parameters while manipulating payloads of unknown mass and inertia. The controller is tested experimentally in a master/slave configuration where the adaptive slave arm is commanded via human operator inputs from a master. Kinematically similar six-joint master and slave arms are used with the last three joints locked for simplification. After a brief initial adaptation period for the unloaded arm, the slave arm retrieves different size payloads and maneuvers them about the workspace. Comparisons are then drawn with similar tasks where the adaptation is turned off. Several simplifications of the controller dynamics are also addressed and experimentally verified.

Carignan, Craig R.↗

NASA NTRS1988

Cooperative control of two arms in the transport of an inertial load in zero gravity

In designing a robot control system for dual arm configurations, the control engineer is faced with two challenges: to derive the equations of motion for a given situation, and to meet certain desired control requirements (for instance, minimum energy). The former may involve closed kinematic chains, such as the case when the two arms are grasping a common object. The latter usually involves nonlinear optimization. These issues are considered in the context of transporting an inertial load using two planar three-link arms. A generalized 'reduction transformation' is applied to the dynamics to remove the singularity in the system equations. A suboptimal minimum energy method is presented to reduce a difficult 12-state, six-control nonlinear optimization to two independent, nonconflicting suboptimizations. A simulation example is provided to illustrate the degree of energy reduction possible using the optimal arm torque distribution that was developed.

Carignan, Craig R.↗

NASA NTRS1988

Tracking and stationkeeping for free-flying robots using sliding surfaces

The authors use the concept of sliding surfaces for generating two types of tracking control laws for a free-flying robot engaged in zero-gravity assembly tasks. Suction control, developed elsewhere for controlling manipulators with stationary bases, is used here to track workspace trajectories for manipulators mounted on mobile platforms. Zone control is formulated for the purpose of stationkeeping a robot maneuvering unit during payload manipulation. Experimental results are described for tests performed on an air-bearing robot tracking payload trajectories along a glass surface.

Carignan, Craig R.↗