Search NASA⌕ Search

Engineering topics

Carlson, L. A.

Publications and source records attributed to Carlson, L. A..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

A direct-inverse method for the prediction of transonic and separated flows about airfoils at high angles of attack

A direct-inverse technique and computer program called TAMSEP that can be used for the analysis of the flow about airfoils at subsonic and low transonic freestream velocities is presented. The method is based upon a direct-inverse nonconservative full potential inviscid method, a Thwaites laminar boundary layer technique, and the Barnwell turbulent momentum integral scheme; and it is formulated using Cartesian coordinates. Since the method utilizes inverse boundary conditions in regions of separated flow, it is suitable for predicting the flowfield about airfoils having trailing edge separated flow under high lift conditions. Comparisons with experimental data indicate that the method should be a useful tool for applied aerodynamic analyses.

Carlson, L. A.↗
NASA NTRS1985

Delamination growth in composite materials

Research related to growth of an imbedded through-width delamination (ITWD) in a compression loaded composite structural element is presented. Composites with widely different interlaminar fracture resistance were examined, viz., graphite/epoxy (CYCOM 982) and graphite/PEEK (APC-2). The initial part of the program consisted of characterizing the material in tension, compression and shear mainly to obtain consistent material properties for analysis, but also as a check of the processing method developed for the thermoplastic APC-2 material. The characterization of the delamination growth in the ITWD specimen, which for the unidirectional case is essentially a mixed Mode 1 and 2 geometry, requires verified mixed-mode growth criteria for the two materials involved. For this purpose the main emphasis during this part of the investigation was on Mode 1 and 2 fracture specimens, namely the Double Cantilever Beam (DCB) and End Notched Flexure (ENF) specimens.

Gillespie, J. W., Jr.↗
NASA NTRS1984

A combined direct/inverse three-dimensional transonic wing design method for vector computers

A three-dimensional transonic-wing design algorithm for vector computers is developed, and the results of sample computations are presented graphically. The method incorporates the direct/inverse scheme of Carlson (1975), a Cartesian grid system with boundary conditions applied at a mean plane, and a potential-flow solver based on the conservative form of the full potential equation and using the ZEBRA II vectorizable solution algorithm of South et al. (1980). The accuracy and consistency of the method with regard to direct and inverse analysis and trailing-edge closure are verified in the test computations.

Weed, R. A.↗
NASA NTRS1984

Inverse transonic airfoil design methods including boundary layer and viscous interaction effects

This report covers the period 1 September 1983 to 31 January 1984. The primary task during this reporting period was the continued development of the massive separation model and computer code (SKANSEP). In particular, detailed investigations were conducted with the boundary layer displacement surface correction technique discovered near the end of the last reporting period. This report will present detailed results using this technique and show comparisons with experimental data.

Carlson, L. A.↗
NASA NTRS1983

THERMTRAJ: A FORTRAN program to compute the trajectory and gas film temperatures of zero pressure balloons

A FORTRAN computer program called THERMTRAJ is presented which can be used to compute the trajectory of high altitude scientific zero pressure balloons from launch through all subsequent phases of the balloon flight. In addition, balloon gas and film temperatures can be computed at every point of the flight. The program has the ability to account for ballasting, changes in cloud cover, variable atmospheric temperature profiles, and both unconditional valving and scheduled valving of the balloon gas. The program was verified for an extensive range of balloon sizes (from 0.5 to 41.47 million cubic feet). Instructions on program usage, listing of the program source deck, input data and printed and plotted output for a verification case are included.

Horn, W. J.↗
NASA NTRS1982

High-Lift Separated Flow About Airfoils

TRANSEP Calculates flow field about low-speed single-element airfoil at high-angle-of-attack and high-lift conditions with massive boundary-layer separation. TRANSEP includes effects of weak viscous interactions and can be used for subsonic/transonic airfoil design and analysis. The approach used in TRANSEP is based on direct-inverse method and its ability to use either displacement surface or pressure as airfoil boundary condition.

Carlson, L. A.↗
NASA NTRS1982

Inverse transonic airfoil design methods including boundary layer and viscous interaction effects

A body-fitted grid embedment technique applicable to inviscid transonic airfoil flow field analysis was developed and verified through a series of tests. Test cases used to verify the technique show that the accuracy of the solution was increased by grid embedding. This enhancement of the solution is especially true when small supercritical zones occur which cannot be adequately described using the main grid only. Results obtained with the SKANFP full potential program are considered with regard to the massive separated flow and high lift and the undesirable unrealistic 'bump' in the vicinity of the separation point due to a mismatch between the unseparated and separated pressure distributions. Techniques used to eliminate this feature are discussed.

Carlson, L. A.↗
NASA NTRS1981

A new thermal and trajectory model for high altitude balloons

A new computer model for the prediction of the trajectory and thermal behavior of high altitude balloons has been developed. In accord with flight data, the model permits radiative emission and absorption of the lifting gas and daytime gas temperatures above that of the balloon film. It also includes ballasting, venting, and valving. Predictions obtained with the model are compared with flight data and newly discovered features are discussed.

Carlson, L. A.↗
NASA NTRS1981

A unified thermal and vertical trajectory model for the prediction of high altitude balloon performance

A computer model for the prediction of the trajectory and thermal behavior of zero-pressure high altitude balloon was developed. In accord with flight data, the model permits radiative emission and absorption of the lifting gas and daytime gas temperatures above that of the balloon film. It also includes ballasting, venting, and valving. Predictions obtained with the model are compared with flight data from several flights and newly discovered features are discussed.

Carlson, L. A.↗
NASA NTRS1981

Test problems for inviscid transonic flow

The paper discusses some results obtained in the solving of test problems for inviscid transonic flow with shock waves using the TRANDES program. The method used employs the full inviscid perturbation-potential flow equation in a Cartesian grid system that is stretched to infinity. The equation is represented by a nonconservative system of finite-difference equations that includes at supersonic points a rotated difference scheme and is solved by column relaxation. Except for the NACA 0012 case with the freestream Mach number equal to 0.95, all test problems were solved straightforwardly and appeared to be converged or close to convergence. The only difficulty was some sensitivity to grid placement, which is typical of the Cartesian formulation

Carlson, L. A.↗
NASA NTRS1980

TRANSEP: A program for high lift separated flow about airfoils

A method and program called TRANSEP is presented that can be used for the analysis of the flow about a low speed airfoil under high lift, massive separation conditions. Since the present program is a modification of the direct-inverse TRANDES code, it can also be used for the design and analysis of transonic airfoils, including the effects of weak viscous interaction. Interactions on program usage, program modifications to convert TRANDES to TRANSEP, and sample cases and results are given.

Carlson, L. A.↗
NASA NTRS1980

Transonic airfoil analysis and design

TRANDES program provides aircraft engineer with accurate and efficient tool for analysis of steady, irrotational, transonic flow over specified two dimensional airfoil in free air. Program is used to design airfoils having prescribed pressure distribution, including effects of weak viscous interaction. TRANDES yield accurate solutions efficiently for biconvex, conventional, and aftcambered airfoils.

Carlson, L. A.↗
NASA NTRS1979

Test problems for inviscid transonic flow

Solving of test problems with the TRANDES program is discussed. This method utilizes the full, inviscid, perturbation potential flow equation in a Cartesian grid system that is stretched to infinity. This equation is represented by a nonconservative system of finite difference equations that includes at supersonic points a rotated difference scheme and is solved by column relaxation. The solution usually starts from a zero perturbation potential on a very coarse grid (typically 13 by 7) followed by several grid halvings until a final solution is obtained on a fine grid (97 by 49).

Carlson, L. A.↗
NASA NTRS1979

Application of direct-inverse techniques to airfoil analysis and design

The direct-inverse technique was developed into a numerical method, called TRANDES, that is suitable for the analysis and design of subsonic and transonic airfoils and for the evaluation of design concepts. A general description of the method is given and its application to a design analysis type of problem is demonstrated. A usage of the method for the low speed high lift case is discussed.

Carlson, L. A.↗
NASA NTRS1977

TRANDES: A FORTRAN program for transonic airfoil analysis or design

A program called TRANDES is presented that is used for the analysis of steady, irrotational transonic flow over specified two-dimensional airfoils in free air or for the design of airfoils having a prescribed pressure distribution, including the effects of weak viscous interaction. Instructions on program usage, listings of the program, and sample cases are given.

Carlson, L. A.↗