Search NASA⌕ Search

Engineering topics

Carney, Casey

Publications and source records attributed to Carney, Casey.

16 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

High-Temperature Oxidation Behavior of Wrought and Additive Manufactured H282 in Direct-Fired Supercritical CO2 Power Cycle Environments

Materials selection is a key concern for corrosion resistance in high temperature and pressure direct-fired supercritical CO2 power cycles. The effect of elevated pressure on corrosion resistance can be critical, as impurities within the supercritical fluid such as H2O and O2 can result in additional corrosion behaviors. Utilizing additive manufacturing (AM) methods for construction of power cycle components requiring both compact and complex designs could be advantageous. AM H282 produced by laser powder bed fusion was exposed to direct-fired conditions (95CO2 – 4H2O – 1 O2) at 750 °C at both atmospheric pressure and supercritical conditions (20 MPa) for up to 4,000 hours. Oxidation behavior, sub-surface carbide formation, and chromia scale volatilization was dependent upon AM preparation techniques and surface modifications. These results are discussed in terms of the potential compatibility issues that may arise when using AM alloys in high temperature regions of direct-fired sCO2 power cycles, particularly for thin-walled components.

Carney, Casey↗
DOE OSTI2024

Environmental Compatibility Issues for Ni-Based Alloys in Direct-Fired Supercritical CO2 Power Cycles

Direct-fired supercritical CO2 (sCO2) power cycles offer potential for high-efficiency power generation from natural gas and other fossil fuels with built-in carbon capture. Ni-based superalloys are the leading candidates for the hottest portions of these systems, where they must endure long-term exposure to high-temperature, high-pressure, high-velocity, impure CO2-rich environments. Herein we describe results of various experimental testing campaigns conduced at NETL showing that under such conditions, several simultaneously occurring degradation modes may be active including surface oxidation, alloy carburization, and oxide volatilization. It will be shown that the rates of degradation can be strongly affected by the alloy composition, impurities in the CO2, manufacturing method (wrought vs additive), and other factors. The influence of these factors in controlling alloy degradation are discussed in the context of potential compatibility issues for components in real sCO2 systems, such as compact heat exchangers. Finally, as a potential remedial measure, ongoing work involving protective coatings suitable for complex geometries is presented.

alloy oxidation↗
DOE OSTI2024

Design and Evaluation of Environmental Barrier Coatings for Protection of Ceramic Matrix Composites in Hydrogen-Based Turbines

This presentation at the 2024 FECM Spring Project Review Meeting summarizes ongoing work at NETL aimed at enabling the use of ceramic matrix composite (CMC) materials in next-generation high-efficiency power generation turbines fueled by hydrogen, natural gas, or other fuels. The work broadly involves three aspects (1) phase-field damage modeling of CMCs and the environmental barrier coatings (EBCs) used to protect them (2) computational design of new and improved EBCs and (3) performance testing of EBCs using a novel gas turbine combustion simulation rig developed at NETL. An overview on current status and next steps for each aspect of the project are presented.

ceramic matrix composite (CMC)↗
DOE OSTI2024

Effect of Silicon on High Temperature Oxidation of Fe-Cr-Si Alloys in Carbon Dioxide Environments

Supercritical carbon dioxide offers the potential for efficient and sustainable power generation. Identifying materials that can be used to construct the high temperature portions of the cycle is a barrier to developing this technology. Various Fe-Cr alloys have been identified as promising construction materials due to a favorable combination of high temperature strength, commercial availability, and cost. The effect of minor alloying elements, particularly Si, has been shown to significantly impact the oxidation and carburization processes for these alloys after relatively short duration exposures in hot carbon dioxide. The long-term impact is less understood, making it challenging to predict performance of real components that will be in service for many years. The objectives in this project are to better understand the long-term oxidation and carburization behavior of Fe-Cr alloys and the important role of Si; to enhance the existing body of literature on the long-term exposure of alloys to hot carbon dioxide; and enable lifetime predictions for future supercritical carbon dioxide power cycle components.

Menna, Valerie↗
DOE OSTI2024

High-Temperature Oxidation Behavior of Wrought and Additive Manufactured Ni-based Alloys in Direct-Fired Supercritical CO2 Power Cycle Environments

Materials selection is a key concern for corrosion resistance in elevated temperature and pressure direct-fired supercritical CO2 (sCO2) power cycles. Herein, the wrought product form of alloy H282, as well as several additional nickel-based commercial alloys (230, 263, 617, 625, 740H), were exposed to direct-fired supercritical CO2 conditions (95CO2 – 4H2O – 1O2) at 750 °C and 20 MPa for over 2,000 h. Additionally, additive manufactured (AM) 282 produced by laser powder bed fusion (LPBF) were also included in the exposures. This paper focuses primarily on the differences observed in the degradation behavior of the wrought and additively manufactured materials. AM samples in the as-printed state were found to form less protective oxide scales resulting in higher oxidation rates compared to wrought samples. However, applying a 600 grit surface finish to the AM samples modified the oxidation behavior to closely resemble that of the wrought material. The AM samples formed Mo-rich carbides in the alloy beneath the oxide following sCO2 exposure, implying potentially higher levels of carbon uptake relative to the wrought material. Conversely, the AM samples seemed to be less affected by water-assisted oxide volatilization compared to the wrought material. The results are discussed in terms of the potential compatibility issues that may arise when using Ni-based alloys in the hot portions of direct-fired sCO2 power cycles, particularly in the case of thin-walled components.

Carney, Casey↗
DOE OSTI2024

High-Temperature Oxidation Behavior of Wrought and Additive Manufactured Alloys in Direct-Fired Supercritical CO2 Power Cycle Environments

Materials selection is a key concern for corrosion resistance in elevated temperature and pressure direct-fired supercritical CO2 (sCO2) power cycles. The effect of elevated pressure on corrosion resistance can be critical, as impurities within the supercritical fluid such as H2O and O2 can have additional corrosion effects than found at ambient pressure conditions. Several wrought nickel-based commercial alloys (230, 263, 282, 617, 625, 740H) were exposed to direct-fired conditions (95CO2 – 4H2O – 1 O2) at 750 °C at both atmospheric pressure (0.1 MPa) and supercritical conditions (20 MPa) for over 2,000 h. Additionally, additive manufactured (AM) 282 produced by laser powder bed fusion (LPBF) were also included in the exposures. Supercritical conditions affected the oxidation behavior of several alloys. Most notably, water-vapor assisted Cr-oxide volatilization was observed at 750 °C supercritical conditions. Many alloys did not form sufficient protective Cr-oxide scales at supercritical conditions, leading to increased oxidation at elevated pressure. Differences in oxidation behavior were also observed for 282 AM samples compared to their wrought counterparts, with the differences also dependent on the LPBF build parameters and post-production treatments (heat treatment and surface finishing procedures). The AM samples formed Mo-rich carbides in the alloy beneath the oxide following sCO2 exposure, implying potentially higher levels of carbon uptake relative to the wrought

Carney, Casey↗